Thermofilm THAT040E Manuel utilisateur
0-40°C Electronic Thermostat with LCD
Display
USER INSTRUCTIONS
Model: THAT040E
TABLE OF CONTENTS
1. Important Safety Instructions
2. Specification Data
3. Controller Guide
4. General
5. Operation Instructions
6. Product Warranty
1. Important Safety Instructions
• Prior to installing and operating this controller device, read the instructions
carefully and retain for
future reference.
• Indoor use only.
• Ensure the rated voltage is 220-240V.
• Do not remove plug from power socket by pulling the power cord. Always grip plug.
• Do not operate this appliance if the power cord or plug becomes damaged.
• Do not immerse in liquid, as this could create an electric shock hazard.
• Do not reach for an appliance that has fallen into water. Switch off at supply and
unplug immediately.
• Do not operate appliance with wet hands. Always ensure hands are dry before
operating or adjusting
any switch on the product or touching the plug and mains supply connections.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or
instruction concerning use of the appliance by a person responsible for their safety.
2. Specification Data
• Rating: 220-240V ~ 50Hz, 9A IP20
• Maximum load Wattage: 2200W (9 amp).
• Environmental temperature: below 40 degree C.
• Range of pre set temperature is from 0.0 to 40.0 degrees C.
• Dimensions of controller box: 115mm x 90mm x 45mm
• Sensor cord length: 890mm
• AC power cord length: 1.6m
3. Controller Guide
1. Sensor Temperature
2. Setting Temperature
3. Down Button
4. Up Button
5. Set Button
6. AC Socket
7. AC Power Cord
8. Sensor Cord
4. General
The THAT040E thermostat is designed to operate a heating device up to 9A at a
controlled temperature.
The heating device is simply plugged into the thermostat and the desired temperature is
set. The LCD
display shows both the actual temperature at the sensor and the desired set
temperature.
The sensor measures the temperature in the first 10mm of the tip, and it is very
important to locate the
sensor as close as possible to the area you wish to heat. For example for reptiles sensor
location should be
at floor level; for birds sensor location should be at normal roosting height, and for plant
propagation the
sensor should be put into the soil at root depth.
Once the unit is turned on with the heater plugged in and the desired temperature set,
you will notice the
sensor temperature will start to increase until it reaches the set temperature. At this
stage, the thermostat
will maintain the set and sensor temperatures within 1 degree C.
5. Operations Instructions
• Plug heater into the thermostat, then plug thermostat into power point and turn on.
• When the unit is plugged in, a “beep” sound will be heard.
• To change the set temperature, press the “set” button. The set display will start to
blink. Press the
“up” or “down” button until the desired set temperature is displayed. Press the “set”
button again to
confirm. After 10 seconds, the set temperature will be locked in. To set a new
temperature, repeat the
above steps. The “up” and “down” buttons do not work, if the “set” button is not pressed
first.
• “E1” will be displayed when the cord of the sensor (pin) is short circuited. “E2” will be
displayed when
the cord of the sensor (pin) is broken. Power supply to the outlet will stop.
• Before removing plug from thermostat, always turn off power at the power point.
Table des matières
Autres manuels Thermofilm Thermostat
Manuels Thermostat populaires d'autres marques
EWELLY
EWELLY EW-181 Manuel utilisateur
Prolon
Prolon T1100 Instructions d'installation
Computherm
Computherm Q20 Manuel utilisateur
Heatmiser
Heatmiser neoStat Manuel utilisateur
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur
