Thermo Sphere SHC-W-01 Manuel
SHC-W-01 SHC-B-01INSTRUCTION GUIDE
CONTROL | TOUCH
SMARTHOME
Excellence in heating solutions.
2
Contents
Compatibility ............................................................... 3
What's in the box? ....................................................... 4
Before you start ........................................................... 5
Installing your thermostat .............................................. 6
Wiring diagram .............................................................. 9
Settings ...................................................................... 13
User interface .............................................................. 14
Set the day and time .................................................. 15
Heating modes ............................................................ 18
Heating schedule ........................................................ 20
SmartHome hub connection ....................................... 22
Technical data ............................................................. 26
Key lock & factory reset ............................................... 27
3
Compatibility
This thermostat is compatible with ThermoSphere
NTC 10K oor sensor probes.
NTC 10kΩ@ 25°C
If you have an existing oor probe from another
thermostat that is not compatible, set your
thermostat to ambient temperature sensing mode.
(Not advisable for timber or other temperature sensitive oors).
Replacing an existing thermostat?
Contact the manufacturer's technical department
and ask for the rating of the oor sensor at 25°C.
4
What’s in the box?
Check you've got everything:
• SmartHome Control
• Floor sensor probe (3m)
• Floor sensor conduit (2m)
• Fixing screws
• Installation guide and warranty information
You will also need:
• Electrical screwdriver
• Electrical back box
• Electrical test meter
5
Before you start
Your thermostat should be:
• Installed 1.2 - 1.5m from the oor
• On an internal wall
• Outside any wet zones (IP21)
• Installed on an RCD protected circuit
• Away from drafts or heat inuences
• Installed so that the oor sensor probe can be laid in a
heated area of the oor
• Installed by a professional, in line with current
electrical regulations and relevant local standards
6
Installing your thermostat
Switch off mains power
You will be installing your thermostat as
part of a high voltage mains electrical
circuit. To ensure your safety and to
protect the thermostat, switch off the
mains power and remove fuse from the
spur before you start the installation.
Fuse Box Fused Switch
CAUTION
High Voltage
Cables
!
OFF
ON ON ON ON ON
OFF
7
Installing your thermostat
Maximum distances
Your thermostat can be installed up to 50m away from the
underoor heating system it is controlling, provided that the
oor sensor is used to control the temperature.
Underoor heating cold tails and oor sensor probes can be
extended up to 50m.
Connect multiple heaters in parallel.
50m max.
8
Installing your thermostat
Release fascia plate
Use a small screwdriver to
undo the captive screw on
the underside of the fascia
casing.
9
Installing your thermostat
Wiring diagram
Connect the Thermostat to the underoor
heating (UFH) cold tail, power supply and oor
temperature sensor.
The oor temperature sensor is not polarity sensitive.
www.thermosphere.com
N1 N
230VAC
Max Load 16A
L L1 S S
Sensor
(No Polarity)
IP21
10
Installing your thermostat
Fix mounting plate in position
Push the power block into the back box and use a screwdriver
to securely x the mounting plate in position.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Thermo Sphere Thermostat
Manuels Thermostat populaires d'autres marques
EWELLY
EWELLY EW-181 Manuel utilisateur
Prolon
Prolon T1100 Instructions d'installation
Computherm
Computherm Q20 Manuel utilisateur
Heatmiser
Heatmiser neoStat Manuel utilisateur
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur
