The Handy THS80 Manuel utilisateur

02/08/2013

THS80

ASSEMBLY AND OPERATING INSTRUCTION

Handy Distribution Spares & Support: 01793 333212

2. Remove and identify loose parts from carton and bag.

1. HELPFUL HINTS:

READ THE INSTRUCTIONS BEFORE ASSEMBLY

zIf your spreader does not spread evenly, be sure the FRONT of the gear box points to the

front of the spreader. The impeller must turn clockwise. Reversing the gear box will cause

the impeller to turn counter clockwise. Clean the impeller plate after each use. Fertilizer

stuck on the impeller blades will cause uneven spreading.

zYour spreader is designed to be pushed at three miles per hour, which is a brisk walking

speed. Slower or faster speeds will change the spread patterns. Wet fertilizer will also

change the spread pattern and flow rate. Clean your spreader thoroughly after each use.

Wash between the shut off plate and bottom of the hopper.

zGears are permanently lubricated at the factory. Do not open the gear box or dirt may

enter.

STEP 1: Install impeller onto the Gear Box & Axle Assembly. Insert Screw M4x20 through

impeller then through Gear Box Axle.

STEP 2: Attach the Wheel Assembly Frame on each side of the Gear Box Axle and Fixing

Connecting Rod, insert two bolts M6x40 into the Fixing Connecting Rod through the Wheel

Assembly Frame. Make sure the hole in the Gear Box Axle is on the right side when assembling

as shown. Attach the Wheel Assembly Frames and Support Leg onto Hopper using bolts M6x70,

lock nuts M6 and Big Flat Washers Ø6. Note: The bolts and nuts needn't be tightened yet.

Left Wheel

Assembly Frame

Right Wheel

Assembly Frame

Make sure the hole in the Gear Box Axle is

on the right side when assembling as

shown.

STEP 3: Insert the Inner Axle Bushing into the Outer Axle Bushing and make sure they are tight.

Install the right Wheel Assembly onto the right Axle using a bolt M5x45 and lock nut M5, and then

install the Cap onto the right Axle using a wooden or rubber hammer. Now install the left Wheel

Assembly onto the left Axle, put a flat washer Ø16 and install the Cap onto left Axle using a

wooden or rubber hammer.

Insert the Inner Axle Bushing into the Outer Axle

Bushing and make sure that they are tight

STEP 4: Insert Upper Handle into the Support Leg and tighten using bolts M6x40 and Lock Nuts

M6. NOW GO BACK AND TIGHTEN ALL NUTS AND BOLTS STARTING WITH FIRST STEP.

DO NOT OVER TIGHTEN.

STEP 5: (1) Insert the Steel Wire head of the control cable into the small hole on the Gauge and

Lever Assembly. (2) Release the two bolts M5x10 and lock nuts on the Press Plate. (3) Put the

Plastic Tube into the slot of the Press Plate. (4) Retighten the two bolts M5x10 and lock nuts

again. (5). Insert R Pin.

STEP 6: ADJUSTMENTS. When you have finished all of the above steps, if the hole at the

bottom of hopper cannot be closed and opened completely by using the handle you may

need to the follow these additional steps. (1) Release the two bolts M5x10 on clamp as

shown. (2). Push the handle to the top position, use your hand to adjust the adjustable plate so

as to make sure the hole at the bottom of the hopper can be closed completely. (3). Push the

handle to the lowest position, use your hand to adjust the adjustable plate so as to make sure the

hole at the bottom of the hopper can be opened completely. (4). Tighten the bolts and nuts on

clamp.

To operate this spreader, push the handle to the lowest position (downwards). You may

move the position of the Wing nut on the Gauge & Lever to adjust the space on the hole

between the hopper and the adjustable plate as per your need when spreading.

Adjusting the position of this nut will

change the size of the hole between the

hopper and the adjustable plate.

USING YOUR SPREADER

1. Determine the approximate square footage of the area to be covered and estimate the

amount of material required using the table on the next page.

2. Before filling the hopper make sure the flow control arm is in the off position and the closure

plate is shut.

3. Break up any lumpy fertilizer as you fill the hopper.

4. Set the adjustable stop with the flow control arm still in the off position. Refer to the

application chart on pages 11 and 12 and to the instructions on the fertilizer bag to select the

proper flow rate setting.

5. The application chart is calculated for application at a vehicle speed of 3 mph, or 100ft. in

approximately 23 seconds. A variation in speed will require an adjustment of the flow rate to

maintain the same coverage. The faster you walk, the wider the broadcast width.

6. Make sure the drive pin is installed in the axle before starting the spreader.

7. Always start walking before opening the closure plate.

8. Always shut the closure plate before turning or stopping.

9. If fertilizer is accidentally deposited too heavily in a small area, soak the area thoroughly with

a garden hose or sprinkler to prevent burning of the lawn.

10.To insure uniform coverage, make each pass so that the broadcast pattern slightly overlaps

the pattern from the previous pass as shown in figure below. The approximate broadcast

widths for different materials are shown in the application chart on pages 11 and 12.

11.When broadcasting weed control fertilizers, make sure the broadcast pattern does not hit

evergreen trees, flowers or shrubs.

12. Always use the rain cover in wet weather conditions to keep the hopper contents dry.

CALCULATING THE AMOUNT OF MATERIAL NEEDED

To calculate the amount of fertilizer you will need to cover your lawn, divide the coverage amount listed on the

label by the weight of the fertilizer bag. For example a 10lb. bag of fertilizer with coverage of 10,000 square

feet will distribute 1lb. of fertilizer every 1,000 square feet at full rate or 1/2lb. of fertilizer every 1,000 square

feet at half rate. For pre-calculated rates see Chart A (Example: 25LB. bag with 15,000 sq. ft. coverage =

1.7lb./1,000 sq. ft.). Use Chart B to find the closest spreader setting (Example: 1.7lb./1000 sq. ft. = Spreader

Setting of 12).

Chart A - Square Foot Coverage per Bag*

LBS/1,000 SQ FT

Weight of Bag (lbs.) 5,000 SQ FT COVERAGE 10,000 SQ FT COVERAGE 15,000 SQ FT COVERAGE

5 1.0 LB. 0.5 LB. 0.3 LB.

10 2.0 LB. 1.0 LB. 0.7 LB.

15 3.0 LB. 1.5 LB. 1.0 LB.

20 4.0 LB. 2.0 LB. 1.3 LB.

25 5.0 LB. 2.5 LB. 1.7 LB.

30 6.0 LB. 3.0 LB. 2.0 LB.

35 7.0 LB. 3.5 LB. 2.3 LB.

40 8.0 LB. 4.0 LB. 2.7 LB.

45 9.0 LB. 4.5 LB. 3.0 LB.

50 10.0 LB. 5.0 LB. 3.3 LB.

*These are only estimates actual amounts may vary.

Chart B - Spreader Settings/Spread Widths

MULTI-

USAGES

LBS/1,000

SQ FT

SPREADER

SETTING

•

SMALL

PARTICLE

SPREAD

•

MEDIUM

PARTICLE

SPREAD

•

LARGE

PARTICLE

SPREAD

1 10 5-6 FT. 6-9 FT. 9-12 FT.

2 12 5-6 FT. 6-9 FT. 9-12 FT.

3 14 5-6 FT. 6-9 FT. 9-12 FT.

4 15 5-6 FT. 6-9 FT. 9-12 FT.

5 17 5-6 FT. 6-9 FT. 9-12 FT.

6 18 5-6 FT. 6-9 FT. 9-12 FT.

7 20 5-6 FT. 6-9 FT. 9-12 FT.

8 23 5-6 FT. 6-9 FT. 9-12 FT.

9 25 5-6 FT. 6-9 FT. 9-12 FT.

FERTILIZER

GRASS

SEEDS

ICEMELT

10 30 5-6 FT. 6-9 FT. 9-12 FT.

*These are only estimates actual spreader settings and spread widths may vary depending on material.

NOTE: DO NOT USE SALT. Using salt in this spreader (especially rock salt) will damage the mechanism

and shorten the life of the machine. If you do choose to use salt in your machine, you should remove

the agitator to reduce damage to the gearbox, use refined deicing salt and thoroughly clean the

spreader after use.

Autres manuels pour THS80

Table des matières

Autres manuels The Handy Épandeur

The Handy

The Handy THSSALT Instructions d'installation et d'entretien

The Handy

The Handy THS125 Instructions d'installation et d'entretien

The Handy

The Handy THTS Manuel utilisateur

The Handy

The Handy THS80 Manuel utilisateur

The Handy

The Handy THS70HDUTY Manuel utilisateur

The Handy

The Handy THSS100 Manuel utilisateur

The Handy

The Handy THTS Manuel utilisateur

The Handy

The Handy THTS175 Manuel utilisateur

The Handy

The Handy THS125 Manuel utilisateur

The Handy

The Handy THSS80 Manuel utilisateur

The Handy

The Handy THDS Instructions d'installation et d'entretien

The Handy

The Handy THS80 Instructions d'installation et d'entretien

The Handy

The Handy THS125HDUTY Manuel utilisateur

The Handy

The Handy THS50 Instructions d'installation et d'entretien

The Handy

The Handy THS50 Manuel utilisateur

The Handy

The Handy THDS Manuel utilisateur

The Handy

The Handy THSSALT Manuel utilisateur

Manuels Épandeur populaires d'autres marques

PEQUEA

PEQUEA GT-100 Manuel utilisateur

Herculano

Herculano H2RS9 Manuel utilisateur

Epoke

Epoke SKE8 Manuel utilisateur

GEA

GEA EL44 Fiche technique

Boss Snowplow

Boss Snowplow TGS 800 Manuel utilisateur

Fisher

Fisher EMERSON 168 Series Manuel utilisateur

Fisher

Fisher POLY-CASTER 78601 Manuel utilisateur

TurfEx

TurfEx RS7200 Manuel du propriétaire

Ferris

Ferris Pathfinder Series Manuel utilisateur

Fayat Group

Fayat Group DYNAPAC S100 Guide de dépannage

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Manuel d'installation et d'exploitation

EASTMAN

EASTMAN CR 500 Manuel utilisateur

Nogueira

Nogueira RoyalFlow-600 Manuel utilisateur

Buyers

Buyers TGS05B Manuel utilisateur

Magnum

Magnum V-BOX PV Series Supplément

Meyer's

Meyer's VB280 Manuel utilisateur

SnowEx

SnowEx VX-4210 Manuel utilisateur

Kramer

Kramer VM-400HDCP Manuel utilisateur