Textron GREENLEE RXM Manuel utilisateur
INSTRUCTION MANUAL
52076396 REV 2 11/16
Read and understand all of the instructions and
safety information in this manual before operating
or servicing this tool.
RXM Reel Stand
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
RXM Reel Stand
Greenlee / A Textron Company
2
Description
The Greenlee RXM Reel Stand is intended for the
dispensing of cable from cable reels.
Safety
Safety is essential in the use and maintenance of
Greenlee tools and equipment. This manual and any
markings on the tool provide information for avoiding
hazards and unsafe practices related to the use of this
tool. Observe all of the safety information provided.
Purpose of this Manual
This manual is intended to familiarize all personnel with
the safe operation and maintenance procedures for the
Greenlee RXM Reel Stand.
Keep this manual available to all personnel.
All specications are nominal and may change as design
improvements occur. Greenlee Textron Inc. shall not be liable for
damages resulting from misapplication or misuse of its products.
® Registered: The color green for material handling equipment is a
registered trademark of Textron Innovations Inc.
KEEP THIS MANUAL
Table of Contents
Description .................................................................... 2
Safety ............................................................................ 2
Purpose of this Manual ................................................. 2
Important Safety Information ........................................ 3
Identication.................................................................. 4
Specications................................................................ 4
Maintenance.................................................................. 4
Operation....................................................................5–6
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
RXM Reel Stand
Greenlee / A Textron Company
3
IMPORTANT SAFETY INFORMATION
SAFETY
ALERT
SYMBOL
This symbol is used to call your attention to
hazards or unsafe practices which could result in
an injury or property damage. The signal word,
dened below, indicates the severity of the hazard.
The message after the signal word provides infor-
mation for preventing or avoiding the hazard.
Immediate hazards which, if not avoided, WILL
result in severe injury or death.
Hazards which, if not avoided, COULD result in
severe injury or death.
Hazards or unsafe practices which, if not avoided,
MAY result in injury or property damage.
Read and understand all of the
instructions and safety information
in this manual before operating or
servicing this tool.
Failure to observe this precaution
may result in injury or property
damage.
• The proper Greenlee spindle is
required for safe operation of this
tool.
• Keep hands and feet clear when
loading and unloading cable reels.
• Head assembly can drop quickly
if not securely held during
adjustment.
• Cable reels must be chocked at all
contact points with the ground to
prevent movement during setup.
Failure to observe these precautions
may result in injury or property
damage.
• Make sure bystanders are clear of the work area
when loading, unloading or dispensing cable.
Nearby personnel can be injured if a cable reel
escapes.
• Do not use the reel roller for cable with damaged
reels. Damaged reels may not roll freely and may
be pulled off the reel roller.
• Never attach casters or wheels to a Greenlee reel
stand.
• Use only on a hard, at, level surface.
• Do not exceed the rated capacity of this tool.
Failure to observe these precautions may result in
injury or property damage.
Use this tool for manufacturer’s intended use only.
Use other than that which is described in this
manuals may result in injury or property damage.
Note: Keep all decals clean and legible, and replace
when necessary.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
RXM Reel Stand
Greenlee / A Textron Company
4
Identification
1. Crank Arm
2. Head Assembly
3. Rollers
4. Jack
Specifications
Capacity: 3000 lb (1360 kg) per unit
Reel Diameters: 21" to 72" (533 to 1829 mm)
Storage Dimensions: 37" x 17" x 11"
(940 x 432 x 279 mm)
Weight: 35 lb (15.9 kg)
Spindles:
647: For loads up to 6000 lb (2722 kg),
47" (1194 mm) max. reel width
684: For loads up to 5000 lb (2268 kg),
61" (1549 mm) max. reel width
Maintenance
The following procedures should be performed at least
annually:
• The internal gearing and bushings of the jack must be
kept lubricated. Apply a small amount of automotive
grease to the internal gearing by using a needle-nose
applicator or standard grease gun on the lubrication
point found on the side of the jack near the crank.
Rotate the jack handle to distribute the grease evenly.
• A lightweight oil must be applied to the handle unit at
both sides of the tube.
Grease
Oil
•A replacement parts kit, cat. no. RXM-REP, is available
for this reel stand.
• A replacement crank arm, cat. no. RXM-HAN, is also
available.
4
3
1
5
6
7
2
5. Carry Handle
6. Pin
7. Base
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
RXM Reel Stand
Greenlee / A Textron Company
5
Operation
1. Two RXM reel stands and one Greenlee reel stand
spindle are required for a complete setup.
2. Make sure the cable reel is chocked to prevent
movement during setup.
3. Insert the spindle through the arbor holes of the
cable reel and center it about the reel’s width.
(Fig.1)
Figure 1.
4. Place reel stands in lifting conguration by removing
the pin and pivoting the jack upward. Then insert
the pin through the upper sockets. (Fig. 2)
Figure 2.
5. Place the reel stand under the spindle and adjust
the jack head assembly by pivoting and sliding it
up or down so that the rollers are just under the
spindle. For very large reels, the jack may also need
to be raised by turning the crank arm to reach the
proper height. (Fig. 3)
Figure 3.
Align the head assembly rollers with the groove at
the end of the spindle. Repeat for other side. (Fig. 4)
Figure 4.
Note: For very wide reels that interfere with crank
arm rotation, lifting is accomplished by turning
the arm in a half circle, folding the arm down, and
repeating this motion.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
RXM Reel Stand
6. Turn the reel stand crank arm clockwise to extend
one reel stand until the cable reel clears the ground.
(Fig. 5)
Figure 5.
Operation (cont’d)
7. Turn the other reel stand crank arm until the spindle
is level and the cable reel rotates freely. (Fig. 6)
Figure 6.
8. When nished dispensing cable, the cable reel
should be lowered and stands put in storage cong-
uration in the reverse manner as described above.
Note: If reel shifts to one side of setup during pull,
lowering is accomplished by turning the crank arm
in a half circle, folding the arm up, and repeating this
motion.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Textron Support et étagère
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
