Texmate Tiger 320 Series Guide de configuration

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.com• Analog Output Mod. (NZ200.1) Page 1

Associated Documents

TTiiggeerr332200SSeerriieessANALOG OUTPUT MODULE SUPPLEMENT

Technical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Analog Output Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Meter Programming Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Analog Output Configuration Programming Codes . . . . . . . . . . . . . . . . . . . . .6

Configure the Output to Drive Remote Instruments or Controllers . . . . . . . .8

Configure for PID Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Configure for Manual Loader Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Connector Pinouts & Component Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Selection Header Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Analog Output Scaling & Calibration Procedure . . . . . . . . . . . . . . . . . . . . . . .12

Select Data Source Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Direct Display Manual Loader Mode Setup Procedure . . . . . . . . . . . . . . . . . . .15

On Demand Manual Loader Mode Setup Procedure . . . . . . . . . . . . . . . . . . . .16

Configure Manual Loader Mode Upper/Lower Limits Procedure . . . . . . . . . .18

Contents

The following documents must be read

together with this supplement:

Relevant Tiger 320 Series User Manual

The operator’s manual provides general information

on the relevant Tiger 320 Series meter.

Tiger 320 Series Programming Code Sheet

The programming code sheet (NZ201) pro-

vides all meter programming codes including

setpoint programming codes.

Registers Supplement

The Registers Supplement (NZ209) provides a

detailed list of all registers available for setpoint

source activation and reset functions.

Setpoint and Relays Supplement

The Setpoint and Relays Supplement (NZ201)

provides detailed descriptions on all setpoint

related topics.

Advanced Calibration and On Demand

Mode Supplement

The Advanced Calibration and On Demand

Mode Supplement (NZ203) provides detailed

descriptions on all calibration related and on-

demand mode topics. List of Figures

Figure 1 – Uses of Analog Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Figure 2 – Programming Code Structure for Analog Output . . . . . . . . . . . . . . . . . . . . . . .5

Figure 3 – Analog Output to Remote Instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Figure 4 – PID via Analog Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Figure 5 – Direct Display Manual Loader Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Figure 6 – On Demand Manual Loader Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Figure 7 – Exploded View of Meter Modular Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Figure 9 – Analog Output Selection Header Placement . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Figure 8 – Rear Cover Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Figure 10 – Multimeter to Meter Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

This document is designed to supplement the information on the Analog

Output Module described in the Tiger 320 Series User Manuals.

Programming Tip

This document has been written using a DI-50 7-segment,

5-digit display meter. When programming meters with

other display options, some display readings may vary to

the diagrams shown.

Texmate Inc. Tel. (760) 598-9899 • www.texmate.comPage 2 • Analog Output Mod. (NZ200.1)

PROGRAMMING TIP Symbol

The programming tip symbol is generic to all Tiger 320 Series documents

and indicates useful tips when programming the instrument.

WARNING Symbol

The WARNING symbol is generic to all Tiger 320 Series documents and

indicates that if the instruction is not heeded, the action may result in loss

of life or serious injury.

General Notices & Tips

NOTE Symbol

The NOTE symbol is generic to all Tiger 320 Series User Manual sup-

plements and indicates important or helpful information on the topic

being discussed.

Definitions The following definitions are relevant to all Tiger 320 Series literature:

If an X appears in the description of a 3-digit programming code or in a configuration pro-

cedure, this means that any number displayed in that digit is not relevant to the function

being explained, or more than one choice can be made.

Meter – Controller

The term meter, as used throughout this document, is a generic term for all Tiger 320 Series

signal processors and controllers

The range of Tiger 320 Series supplements contain three graphic symbols to aid you:

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.com• Analog Output Mod. (NZ200.1) Page 3

The analog output signal can be used for the following applications (see Figure 1):

•To drive remote process control instruments.

• As an isolated 4 to 20 mA/0 to 10 V DC signal for further control processing via a PLC.

• As a 4 to 20 mA PID output for process control applications (e.g. temperature control).

• As a manual loader output to manually control the operation of actuated plant equipment such as

valves, dampers, hydraulic and pneumatic cylinders and slides.

PLC

SUPER

Prog.

°C

100

200

300

Chart Recorder

Input to Remote

Display

POWER

ERROR

ETHERNET

PORT

IN SIM

OUT RELAYS

24VDC OUT

85 - 264VAC

50/60 Hz

PLC

SUPERSUPER

100

Input to PLC or

Process Controller

Isolated Analog Output

4-20 mA PID Output

for Process Control

Applications

Input to Chart

Recorder

Remote Displays

PLC

Process

PID from

SP1

PID from

SP2

Electrically Actuated

Valves, etc

Hydraulic, Pnuematic

Actuator Rams, etc

Control Output

to Actuated

Devices

Figure 1 –Uses of Analog Output

Analog Output: AIC or AIV: Single isolated 0/4 to 20 mA (or reverse) or isolated 0 to 10 V

DC (or reverse). Header Selectable.

ADV: Dual isolated 0 to 10 V DC (or reverse).

Accuracy: 0.02 % of full scale.

Drift: Typical 50 ppm/°C.

Resolution: 16-bit 1/45000 counts equal to 0.4 µA on current scale, 250 µV on voltage

scale.

Compliance: 500 Ω@20 mA.

Update Rate: Typical 7 per second.

Analog Output

Functions

Technical

Specifications

Technical Description

The data source for the ana-

log output can be selected

from any processed meter

input signal.

The span range of the analog

output can be as small as 100

counts between the low and

high analog output signal.

Once calibrated, the span

range of the analog output

can be easily changed

(rescaled) without having to

recalibrate the output. The

low and high analog output

signal values (mA or volts)

follow the new span range.

There are three analog output options available:

•AIC Single 0/4 to 20 mA.

•AIV Single 0 to 10 V DC.

•ADV Dual 0 to 10 V DC with common 0.

The analog output module is a programmable, isolated, 16-bit output that is scalable to any

desired span within the full scale range of the controller. The single versions can be user con-

figured for either 4-20 mA or 0-10 V DC or reverse using a selection header. The dual version

can be user configured for 0-10 V DC or reverse. The selected analog output module version is

mounted on the meter’s output carrier board. See Figure 7.

The analog output can be programmed over:

•The full scale range of the meter and the selected input module.

•Any part within the full scale range of the selected input channel.

•Any part within the full scale range of the linearized input signal.

•The proportional band of the PID register.

AIC and AIV are mounted on the same

board and are header selectable

Texmate Inc. Tel. (760) 598-9899 •www.texmate.comPage 4 •Analog Output Mod. (NZ200.1)

Input to PLC

The isolated analog output signal from the meter is fed into a PLC where it can be further

processed.

PID Output

The analog output signal can be used in PID process control applications. The PID control data

is fed through the analog output directly to a process control system.

The PID data is sourced from the PID proportional band register, register 50 for SP1 and reg-

ister 51 for SP2, in the Select Source Data menu of Code 1 (See Figure 2).

Manual Loader Mode

In the manual loader mode, the meter is configured so that the display, in engineering units, accu-

rately relates to the analog output.

The manual loader mode is used where precise and repeatable control is required from a digital dis-

play and manual control source. The front panel and buttons are used to control the analog

output signal.

The manual loader mode can be configured to function in one of two ways:

•Directly displayed on the meter when the meter is in the operational display.

•Or as an on demand function of the meter activated by pressing the button for 4 seconds.

Direct Display Manual Loader Mode

The meter can be configured in Code 1 to function exclusively as a manual loader using the

meter’s and buttons to adjust the analog output signal.

On Demand Manual Loader Mode

The manual loader mode can also be configured as an on demand function of the meter. It is

activated by pressing the button for 4 seconds after being configured in the calibration mode

and Code 1.

When activated, the analog output signal is adjusted using the meter’s and buttons.

Upper and Lower Limits

Upper and lower limits can be set for the manual loader mode. The setpoint activation values

for setpoint 5 becomes the upper limit and setpoint 6 becomes the lower limit.

When either the direct display or on demand manual loader mode is programmed into the

meter, the values for setpoint 5 and setpoint 6 are activated as upper and lower limits.

The meter’s programming codes are divided into two modes (see Figure 2):

•Main Programming Mode.

•Setpoint Programming Mode.

Each mode is accessible from the operational display. The meter is in the operational display

when it is displaying a processed input signal.

Meter Programming

Codes

Main Programming Mode

The main programming mode is where the analog output is calibrated, the data source for the ana-

log output selected, and the manual loader mode (direct display or on demand) selected.

Setpoint Programming Mode

The setpoint programming mode is where the meter is configured for 4-20 mA or 0-10 V DC PID

output on setpoints SP1 and SP2 and the manual loader mode upper and lower limits on set-

points SP5 and SP6 are set (see Figure 2).

Texmate, Inc. Tel. (760) 598-9899 •www.texmate.com•Analog Output Mod. (NZ200.1) Page 5

To enter press and at the same time:

Main Programming Mode

Calibration Modes for Input and Output

Code 1 –Display Configuration

[CAL]

[Cod_1]

To enter press and at the same time

Setpoint Programming Mode

Setpoint 1

[SP_1]

Setpoint Activation Values

Setpoint 2

[SP_2]

Setpoint 3

[SP_3]

Setpoint 4

[SP_4]

Setpoint 5 UPPER LIMIT

[SP_5]

Setpoint 6 LOWER LIMIT

[SP_6]

Enter these menus to adjust setpoint activation values

Setpoint 1 PID

[SPC_1]

Setpoint & Relay Control Function Settings

Setpoint 2 PID

[SPC_2]

Enter these menus to configure setpoint control values:

Allows you to:

•Scale the analog output LOW/HIGH (zero/span)

display readings.

•Calibrate the analog output milliamp/voltage out-

put signal.

•Select the ON DEMAND manual loader mode.

See Page 4 for CAL mode breakdown.

Allows you to:

•Select the DIRECT DISPLAY manual loader

mode.

•Select the source of data for analog output 1.

See Page 4 for CAL mode breakdown.

Codes 2 to 9 (or 10 if the meter is a bargraph

display version) are still available but are not

relevant to programming the analog output.

Configure PID mode control settings for SP1

(see Page 6 for PID mode breakdown).

Display Brightness

[bri]

Allows you to adjust the display brightness.

Prog.

Operational Display

Prog.

Operational Display

To save a new setpoint configuration

setting and return to the operational

display at any point, press the but-

ton once.

Then press the and button at the

same time to exit.

Save Setpoint Settings & Exit

To save a new main programming mode con-

figuration setting and return to the operational

display at any point, press the button once.

Then press the and button at the same

time to exit.

Save Code Settings & Exit

Figure 2 –Programming Code Structure for Analog Output

Configure PID mode control settings for SP2

(see Page 6 for PID mode breakdown).

Configure manual loader mode UPPER limit.

[SP_5] [10000] use buttons to adjust

Configure manual loader mode LOWER limit.

[SP_6] [-10000] use buttons to adjust

Not relevant to analog output.

When not used for PID analog output,

SPC_1 and SPC_2 are still available for

setpoint control.

SPC_3 to SPC_6 are still available but

are not relevant to programming the

analog output.

Texmate Inc. Tel. (760) 598-9899 •www.texmate.comPage 6 •Analog Output Mod. (NZ200.1)

0 No function

1 On Demand TARE from the PROGRAM button

2 On Demand Single-point Calibration from the PROGRAM button

(requires single input source)

3 On Demand Two-point Calibration from the PROGRAM button

(requires dual input source)

4 On Demand Primary Input Compensation Mode from the PROGRAM

button

5 On Demand Manual Loader Mode (no increase/decrease with

HOLD active)

[rESLt] [Ch1] [Ch2] [Ch3] [Ch4] [tot_1] [tot_2] [PEAK]

[1 to 244]

[tArE]

[VALEY]

[diSP]

CALIBRATION MODES FOR INPUT AND OUTPUT

THIRD DIGIT

0 Result

1 Channel 1

2 Channel 2

3 Channel 3

4 Channel 4

FIRST DIGIT SECOND DIGIT

OBJECT FOR 2nd DIGIT

0 Manual Calibration (requires NO input source)

1 Two-point Calibration (requires dual input source)

2 Calibrate Thermocouple (requires K type thermocouple input source)

3 Calibrate RTD (requires RTD 385 input source)

4 Calibrate Smart Input Module. Note:This function is not available on all

input modules

5 Calibrate Analog Output mA/V Output Signal (requires multimeter

connected to pins 16 and 17)

0 Set baud rate, parity, address

1 Set Auto Zero Maintenance for 3rd digit

2 Set Averaging Samples & Averaging Window for 3rd digit

3 Set K Factor & Cutoff for Totalizer

4 Setup 32-point Linearization Tables

5 Scale Analog Output LOW/HIGH (zero/span) Display Readings

1 Analog Output 1

2 Analog Output 2

(under development)

OBJECT FOR 2nd DIGIT

Analog Output

Configuration

Programming Codes

The analog output is scaled and calibrated in the calibration mode of the meter’s main pro-

gramming mode. The meter is configured for specific analog output applications in the calibra-

tion mode and Code 1 of the the meter’s main programming mode.

PID control via the analog output and analog output upper and lower limits are set in the set-

point programming mode.

Pressing the and buttons at the same time enters the main programming mode. To save

a new configuration setting and return to the operational display, press the button once and

then press the and buttons at the same time.

Use buttons

to set CAL_L

Use buttons

to set CAL_h

Use buttons

to set ZERO

Use buttons

to set FULL SCALE

FRONT PANEL ANNUNCIATORS

0 ON when Setpoints are ON (relay

energized)

1 ON when Setpoints are OFF (relay

de-energized)

2 Always OFF.

3 LED SP1 ON indicates RISING sig-

nal trend.

LED SP2 ON indicates FALLING

signal trend.

DATA DISPLAY SOURCE

0 Normal Display Mode (i.e. operational dis-

play shows selected register) updates

every 0.5 seconds

1 Manual Loader Mode (Direct Display). See

Note 1

2 Update at sample rate selected in Code 2

5 Select data source as per 3rd digit

6 Select display format as per 3rd digit

7 Select text character as per 3rd digit

SELECT DATA SOURCE FOR

0 Primary Display

1 Second Display. See Note 2

2 Third Display. See Note 2

3 Peak/Valley

4 Analog Output 1

5 Analog Output 2 (under development)

6 Totalizer 1

7 Totalizer 2

CODE 1 –DISPLAY CONFIGURATION: SELECT DATA SOURCE FOR ANALOG OUTPUT

FIRST DIGIT SECOND DIGIT THIRD DIGIT

See diagram below

See data sheet

Select Data Source

Select Display Format

Select Text Character

Use the and

buttons to cycle

through the options

Select Data Source

Use the and

buttons to select a reg-

ister as the data source

for the analog output

Note 2:

These options are only for use with

meters that have more than one

display. With bargraph meters the

PRIMARY display is the digital dis-

play, and the SECONDARY display

is the bargraph display.

Note:

First digit selections are not

relevant to the analog output.

0 Functions

Activated by

Pressing the

PROGRAM

Button

1 Calibration

Procedures

2 Related

Calibration

Functions

Note 1:

Upper and lower limits can be set

in SP5 and SP6 of the setpoint

programming mode.

PID for SP1 = Register 50

PID for SP2 = Register 51

Texmate, Inc. Tel. (760) 598-9899 •www.texmate.com•Analog Output Mod. (NZ200.1) Page 7

Set Up PID Mode Settings

Basic Level

Select: Mode/OFF

Set Deviation from 1 to 65535

counts. Selected counts apply +

and –from setpoint value

Set the Span Set the Proportional Band Value Set the Integral Value

Set the Derivative Value Set the Anti-reset Wind-up % PB Set the Minimum Cycle Time

PID FROM SETPOINT 1

AND 2 ONLY MIN 0%

MAX 999.9%

MIN 0

MAX 99999

MIN 0

MAX 9999.9

MIN 0

MAX 999.9

MIN 0.1%

MAX 100.0%

MIN 0 secs

MAX 1000.0 secs

Note:

The output from RELAY 1 is

disabled if minimum cycle

time set to 0

0 No Latching

1 Relay Latched

2 Manual Relay Reset

3 Relay Latched with Manual Relay

Reset

4 Relay Latched Off

5 Hysteresis, Deviation & PID Mode

6 Timer Modes:

•Normal Delay.

•Repeat ON.

•Pulse ON.

•1-Shot ON.

•Repeat OFF.

•Pulse OFF.

•1-Shot OFF.

Note:

With PID active, all SP1 functions

set in [XX6] are not functional.

7 Advanced Functions Mode:

•Reset Trigger.

•Reset Destination.

•Reset Mode.

•Reset Constant.

•Trigger Print from SP.

•Trigger Log from SP.

•Annunciator Flashing & SP Tracking.

Note:

[XX5], [XX6], and [XX7] are set up

procedure settings only. To finish,

reset to 0-4 as required for setpoint

latching and relay reset modes.

Relay Energize Function

0 Energized ABOVE setpoint value.

1 Energized BELOW setpoint value.

2 Energized ABOVE setpoint value with FALLING

INPUT SIGNAL INITIAL START-UP INHIBIT.

3 Energized BELOW setpoint value with RISING

INPUT SIGNAL INITIAL START-UP INHIBIT.

SP Activation Source

0 Activate Setpoint Source from

Selected Register

1 Select Source for Setpoint

Note:

[X1X] is a register selection procedure

only. To finish, reset to [X0X] to activate

the selection, or reset to 2-7 as required

for digital input selection.

2 Digital Input –Capture Pin

3 Digital Input –D1

4 Digital Input –D2

5 Digital Input –D3

6 HOLD Pin

7 LOCK Pin

SP Delay & Timing Functions

FIRST DIGIT SECOND DIGIT THIRD DIGIT

See Set Up PID

Mode Settings

below

SETPOINT PROGRAMMING MODE –SETPOINT CONTROL SETTINGS FOR PID ONLY

Use the

buttons to cycle

through the menu

Use the or

button to select a

source for setpoint

Select Source for Setpoint Functions

Select Tracking Setting

Select Flash Setting OFF or ON

OFF= Tracking Off

1 = SPX tracks SP1

2 = SPX tracks SP2

3 = SPX tracks SP3

4 = SPX tracks SP4

5 = SPX tracks SP5

6 = SPX tracks SP6

Set Hysteresis from 0 to 65535

counts. Selected counts apply +

and –from setpoint value

SPC_1 or SPC_2, third

digit set to [XX5]

Intermediate or Advanced Level

Select Hysteresis, Deviation or PID Mode

and adjust to required setting.

Reset SPC_X to [XX0]

Programming Tip

If you do not require any

of the functions in this

mode, ensure it is set to:

[rESLt]

[Ch1]

[Ch2]

[Ch3] [Ch4] [tot_1] [tot_2]

[PEAK]

[1 to 244]

[tArE]

[VALEY]

[diSP]

Note:

If PID is selected in [XX5],

the Timer Delay [XX6] and

Reset and Trigger Functions

[XX7] revert to [ModE][oFF]

and cannot be adjusted.

PPP

Texmate Inc. Tel. (760) 598-9899 •www.texmate.comPage 8 •Analog Output Mod. (NZ200.1)

See Figure 3. The analog output is capable of

driving almost any remote process instrument

that displays a 4 to 20 mA or 0 to 10 V DC signal.

The analog output must be connected to the

remote process instrument and configured in

the following steps:

1) If AIV or AIC option installed, make sure the

ANALOG OUTPUT SELECTION HEADER is

correctly selected for the output signal type: volts

or milliamps.

See Selection Header Positioning for details.

2) For AIC or AIV option, connect a multimeter to

pins 2 and 3 on Terminal 4. For ADV option, con-

nect multimeter to pins 1 and 2 for Analog 2 and

pins 2 and 3 for Analog 1.

3) Calibrate the analog output using the multimeter

input.

See Analog Output Calibration Procedure for

details.

Remote Instruments:

4) Connect the remote process instrument to Terminal 4 (see Figure 7).

5) Select the source of data for the analog output in Code 1 of the meter’s main programming mode.

See Select Data Source Procedure for details to configure the data source for the analog out-

put to a remote instrument.

PLC:

4) Connect the PLC to Terminal 4 (see Figure 7).

5) Select the source of data for the analog output in Code 1 of the meter’s main programming mode.

See Select Data Source Procedure for details to configure the data source for the analog out-

put to a PLC.

Prog.

°C

100

200

300

Chart Recorder

Input to

Remote

Display

Isolated Analog

Output

Input to

Chart

Recorder

Remote Displays

POWER

ERROR

ETHERNET

PORT

IN SIM

OUT RELAYS

24VDC OUT

85 - 264VAC

50/60 Hz

PLC

SUPER

100

Input to

PLC

Process

Controller

Input to

Process

Controller

Prog. 4-20 mA PID

Output for

Process

Control

Applications

Process

Control

Device

PID from

SP1

PID from

SP2

Figure 4 –PID via Analog Output

Figure 3 –Analog Output to Remote

Instruments

The analog output signal can be

used to feed PID control data

from the meter to control

process applications.

The analog output must be con-

nected to the control device and

configured in the following steps

(see Figure 4):

Configure for PID

Output

Configure the Output

to Drive Remote

Instruments or

Controllers

1) If AIV or AIC option installed, make sure the ANALOG OUTPUT SELECTION HEADER is cor-

rectly selected for the output signal type: volts or milliamps.

See Selection Header Positioning for details.

2) For AIC or AIV option, connect a multimeter to pins 2 and 3 on Terminal 4. For ADV option, con-

nect multimeter to pins 1 and 2 for Analog 2 and pins 2 and 3 for Analog 1.

3) Calibrate the analog output using the multimeter input.

See Analog Output Calibration Procedure for details.

4) Connect the process control device to Terminal 4 (see Figure 7).

5) Enter Code 1 of the meter’s main programming mode:

a) Set Code 1 to [X54]. This selects analog output 1.

b) Select register 50 (SP1 PID output value) or register 51 (SP2 PID output value) as the

source of data for the analog output signal of SP1 or SP2 as required.

See Select Data Source Procedure for details to configure the PID as the source of data for

the analog output signal of SP1 or SP2.

6) Enter the setpoint programming mode and configure setpoint 1 or setpoint 2, or both for PID functions.

See Setpoints and Relays Supplement for full details on the PID mode.

Texmate, Inc. Tel. (760) 598-9899 •www.texmate.com•Analog Output Mod. (NZ200.1) Page 9

Configure for Manual

Loader Mode Direct Display Manual Loader Mode

The meter can be configured to operate exclusively as a manual loader to control equipment

while in the operational display.

The analog output must be connected to the control equipment and configured in the following steps:

1) If AIV or AIC option installed, make sure the ANALOG OUTPUT SELECTION HEADER is cor-

rectly selected for the output signal type: volts or milliamps. See Selection Header Positioning for

details.

2) For AIC or AIV option, connect a multimeter to pins 2 and 3 on Terminal 4. For ADV option, con-

nect multimeter to pins 1 and 2 for Analog 2 and pins 2 and 3 for Analog 1.

3) Scale and calibrate the analog output using the multimeter input. See Analog Output Calibration

Procedure for details.

4) Connect the control equipment to Terminal 4 (see Figure 7).

5) Enter Code 1 of the meter’s main program-

ming mode:

a) Set to [X54]. Select [DiSP] as the

source of data for the analog output.

b) Reset Code 1 to [X50]. Select [DiSP] as

the source of data for the primary dis-

play.

c) Reset Code 1 to [X14]. This selects

Manual Loader Mode (Direct Display)

for Analog Output 1.

See Direct Display Manual Loader

Mode Procedure for details to configure

the meter for direct display manual

loader mode.

Prog.

Isolated Analog

Output to Control

Device

Operational Display

Electrically Actuated

Valves, etc

Hydraulic, Pnuematic

Actuator Rams, etc

Prog.

Operational Display

Press

4 secs

Prog.

Isolated Analog

Output to Control

Device

Electrically Actuated

Valves, etc

Hydraulic, Pnuematic

Actuator Rams, etc

Figure 6 –On Demand Manual Loader Mode

Figure 5 –Direct Display Manual

Loader Mode

Return to the operational display. The meter is now configured for direct display manual loader

mode. Pressing the UP or DOWN buttons increases or decreases the analog output.

On Demand Manual Loader Mode

The meter can be configured to operate

on demand as a manual loader on con-

trol equipment. This leaves the meter

free to perform normal control functions.

The analog output must be connected to

the actuated plant equipment and con-

figured in the following steps:

1) If AIV or AIC option installed, make sure

the ANALOG OUTPUT SELECTION

HEADER is correctly selected for the out-

put signal type: volts or milliamps. See

Selection Header Positioning for details.

2) For AIC or AIV option, connect a multi-

meter to pins 2 and 3 on Terminal 4. For

ADV option, connect multimeter to pins

1 and 2 for Analog 2 and pins 2 and 3

for Analog 1.

3) Scale and calibrate the analog output

using the multimeter input. See Analog

Output Calibration Procedure for details.

4) Connect the control equipment to Terminal 4 (see Figure 7).

5) Enter Code 1 of the meter’s main programming mode:

a) Set to [X54]. Select [DiSP] as the source of data for the analog output.

b) Reset Code 1 to [X50]. Select a channel (CH1 to CH4) as the source of data for the pri-

mary display.

c) On leaving Code 1, set to [X10]. This selects manual loader mode on the primary display.

Texmate Inc. Tel. (760) 598-9899 •www.texmate.comPage 10 •Analog Output Mod. (NZ200.1)

Connector Pinouts &

Component Layout Pinout details for both single and dual analog output modules are

shown in table TERMINAL 4 opposite and Figure 7 below.

In Figure 7 – Exploded View of Meter Modular Boards, all circuit

boards are shown in an exploded assembly view of the meter with-

out the meter case. All connector terminal numbers or names are

identified. These are described in detail in the relevant Tiger user

manual.

The analog output module is mounted on the component side of the

output carrier board. The analog output selection header is easily

repositoned by pulling the output carrier board from the meter case.

See Selection Header Positioning for further details.

POWER

AC / DC Power

Output

Carrier

Board

Serial

Output

Module

Analog

Output

Module

Display

Board

Processor

Board

Main

Board

TERMINAL 1

Input Module Pins

Relay

Module

TERMINAL 6

Relay Output Pins

TERMINAL 5

Serial Output Pins

RJ-11 Socket

TERMINAL 4

Analog Output Pins

Input Signal

Conditioner

If selected, TTL

Logic Level Circuitry

placed here

Figure 7 –Exploded View of Meter Modular Boards

6) Enter the calibration mode [CAL] of the meter’s main programming mode and set the 2nd

digit to [X5X] to select On Demand Manual Loader Mode. Select the same channel that you

selected in Step 5 in the 3rd digit:

•[X51] = Analog Output 1.

•[X52] = Analog Output 2.

See On demand Manual Loader Mode Procedure for details to configure the meter for on demand

manual loader mode.

To activate the on demand manual loader mode, press the PROGRAM button for 4 to 5 secs.

The meter toggles between [Ch1] and the current display counts. Pressing the UP or DOWN

buttons increases or decreases the analog output.

TERMINAL 2

Function Pins

TERMINAL 4

21 3

TERMINAL 4

AIC or AIV

SINGLE ANALOG OUT

ADV

DUAL ANALOG OUT

ANALOG 1

ANALOG 2

COMMON

ANALOG 1

COMMON

21 3

N/C

Voltage or Current

Selection Header

Pin No. Function

Not Connected

–Common

+ Analog 1

TERMINAL 4

AIC / AIV: Single Output

+ Analog 2

–Common

+ Analog 1

ADV: Dual Output

Autres manuels pour Tiger 320 Series

Table des matières

Manuels Système d'E/S populaires d'autres marques

WAGO

WAGO 750-344 Manuel utilisateur

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

M-system

M-system R3Y-RS8 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur