Texas Instruments TPS7A39EVM-865 Manuel utilisateur

SBVU034–July 2017

TPS7A39EVM-865 Evaluation Module

User's Guide

SBVU034–July 2017

TPS7A39EVM-865 Evaluation Module

This user’s guide describes the operational use of the TPS7A39EVM-865 evaluation module (EVM) as a

reference design for engineering demonstration and evaluation of the TPS7A3901DSC, low-dropout linear

regulator (LDO). Included in this user’s guide are setup and operating instructions, layout guidelines, a

printed circuit board (PCB) layout, a schematic diagram, and a bill of materials (BOM).

Throughout this document, the terms demonstration kit,evaluation board, and evaluation module are

synonymous with the TPS7A39EVM-865.

The following related documents are available through the Texas Instruments web site at www.ti.com.

Related Documentation

Device Literature Number

TPS7A39 SBVS263

www.ti.com

2SBVU034–July 2017

Submit Documentation Feedback

TPS7A39EVM-865 Evaluation Module

Contents

1 Introduction ................................................................................................................... 3

1.1 Before You Begin................................................................................................... 3

2 EVM Setup.................................................................................................................... 4

2.1 Input/Output Connectors and Jumper Descriptions............................................................ 4

2.2 TP12 – BUF ......................................................................................................... 5

2.3 Soldering Guidelines ............................................................................................... 6

2.4 Equipment Connection............................................................................................. 6

3 Operation ..................................................................................................................... 6

4 PCB Layout................................................................................................................... 7

5 Schematic..................................................................................................................... 8

6 Bill of Materials............................................................................................................... 9

List of Figures

1 Assembly Layer.............................................................................................................. 7

2 Top Layer Routing........................................................................................................... 7

3 Bottom Layer Routing....................................................................................................... 7

4 TPS7A39EVM-865 Schematic............................................................................................. 8

List of Tables

1 TPS7A39EVM-865 BOM.................................................................................................... 9

Trademarks

All trademarks are the property of their respective owners.

www.ti.com

Introduction

SBVU034–July 2017

TPS7A39EVM-865 Evaluation Module

1 Introduction

The Texas Instruments' TPS7A39EVM-865 EVM helps design engineers evaluate the operation and

performance of the TPS7A39 for possible use in their own circuit application. This particular EVM

configuration contains a single TPS7A39 device which integrates a positive and a negative monolithic

bipolar LDO to simplify signal chain dual-rail power-supply design. The regulator is capable of delivering

up to 150 mA per channel to the load. For stability, use a 10-µF (or larger) input and a 10-µF (or larger)

output capacitor for each channel of the TPS7A39.

1.1 Before You Begin

The following warnings and cautions are noted for the safety of anyone using or working close to the

TPS7A39EVM-865. Observe all safety precautions.

Warning Warning Hot surface. Contact may cause burns. Do not touch.

CAUTION

The circuit module may be damaged by overtemperature. To avoid damage,

monitor the temperature during evaluation and provide cooling, as needed, for

your system environment.

CAUTION

Some power supplies can be damaged by application of external voltages. If

using more than one power supply, check your equipment requirements and

use blocking diodes or other isolation techniques, as needed, to prevent

damage to your equipment.

CAUTION

The circuit module is not a finished product or electrical appliance. The module

does not contain current or voltage thresholds for circuit protection. It must be

used by qualified personnel with additional equipment for evaluation only.

EVM Setup

www.ti.com

4SBVU034–July 2017

Submit Documentation Feedback

TPS7A39EVM-865 Evaluation Module

2 EVM Setup

This section describes how to properly connect and setup the TPS7A39EVM-865, including the jumpers

and connectors on the EVM board.

2.1 Input/Output Connectors and Jumper Descriptions

2.1.1 J1 – OUTP_S

Positive output sense test point. An SMA connector (not provided) can be added here.

2.1.2 J2 – OUTP

Regulated positive output voltage connector.

2.1.3 J3 – INP_S

Positive input sense test point. An SMA connector (not provided) can be added here.

2.1.4 J4 – INN_S

Negative input sense test point. An SMA connector (not provided) can be added here.

2.1.5 J5 – GND

Positive output ground return connector.

2.1.6 J6 – GND

Positive input ground return connector.

2.1.7 J7 – OUTN_S

Negative output sense test point. An SMA connector (not provided) can be added here.

2.1.8 J8 – INP

Positive input voltage power-supply connector. Keep the positive input lead as short as possible to

minimize input inductance.

2.1.9 J9 – Positive LDO Resistor Divider

TPS7A39EVM-865 is prepopulated with four resistor dividers for the positive output voltage. Place a short

to select the desired output voltage from the silkscreen.

2.1.10 J10 – INN

Negative input voltage power-supply connector. Keep the negative input lead as short as possible to

minimize input inductance.

2.1.11 J11 – OUTN

Regulated negative output voltage connector.

2.1.12 J12 – GND

Negative input ground return connector.

2.1.13 J13 – GND

Negative output ground return connector.

www.ti.com

EVM Setup

SBVU034–July 2017

TPS7A39EVM-865 Evaluation Module

2.1.14 J14 – NR/SS

TPS7A39EVM-865 is prepopulated with two NR/SS capacitors. Select the desired value.

2.1.15 J15 – EN

Output enable. To enable the outputs, connect a jumper to short INP to EN.

2.1.16 J16 – Negative LDO Resistor Divider

TPS7A39EVM-865 is prepopulated with five options for the negative output voltage. Place a short to

select the desired output voltage from the silkscreen.

2.1.17 TP1 – OUTP_S

Positive output sense test point.

2.1.18 TP2 – INP_S

Positive input sense test point.

2.1.19 TP3 – FBP_S

Positive feedback sense test point.

2.1.20 TP4 – INN_S

Negative input sense test point.

2.1.21 TP5 – NR/SS

NR/SS sense test point.

2.1.22 TP6 – FBN_S

Negative feedback sense test point.

2.1.23 TP7 – OUTN_S

Negative output sense test point.

2.1.24 TP8 – EN_S

Enable sense test point.

2.1.25 TP9 – GND

Ground test point.

2.1.26 TP10 – GND

Ground test point.

2.1.27 TP11 – GND

Ground test point.

2.2 TP12 – BUF

Buffer pin test point.

EVM Setup

www.ti.com

6SBVU034–July 2017

Submit Documentation Feedback

TPS7A39EVM-865 Evaluation Module

2.3 Soldering Guidelines

To avoid damaging the integrated circuit (IC), use a hot-air system for any solder rework to modify the

EVM for the purpose of repair or other application reasons.

2.4 Equipment Connection

Use the following guidelines when connecting the equipment:

1. Set the positive input supply to 33 V (max), and turn the power supply off.

2. Set the negative input supply to –33 V (min), and turn the power supply off.

3. Connect the positive voltage lead from the input power supply to INP at the J8 connector of the EVM.

4. Connect the negative voltage lead from the input power supply to INN at the J10 connector of the

EVM.

5. Connect the ground lead from the input power supply to GND at the J6 and J12 connector of the EVM.

6. Connect a 0 mA to 150 mA load between OUTP and GND.

7. Connect a 0 mA to 150 mA load between OUTN and GND.

8. Disable the output by floating J15.

3 Operation

Operate the EVM using the following steps:

1. Turn on the power supplies.

2. Enable the output by jumping J15, the EN pin, to VIN.

3. Vary the respective load and input voltage, as necessary, for test purposes.

www.ti.com

PCB Layout

SBVU034–July 2017

TPS7A39EVM-865 Evaluation Module

4 PCB Layout

Figure 1 to Figure 3 illustrate the PCB layout for this EVM.

Figure 1. Assembly Layer Figure 2. Top Layer Routing

Figure 3. Bottom Layer Routing

Schematic

www.ti.com

8SBVU034–July 2017

Submit Documentation Feedback

TPS7A39EVM-865 Evaluation Module

5 Schematic

Figure 4 is the schematic for this EVM.

Figure 4. TPS7A39EVM-865 Schematic

www.ti.com

Bill of Materials

SBVU034–July 2017

TPS7A39EVM-865 Evaluation Module

6 Bill of Materials

The BOM for this EVM is shown in Table 1.

(1) These assemblies are ESD sensitive, observe ESD precautions.

(2) These assemblies must be clean and free from flux and all contaminants. Use of no-clean flux is not acceptable.

(3) These assemblies must comply with workmanship standards IPC-A-610 Class 2.

(4) Unless otherwise noted in the Alternate Part Number or Alternate Manufacturer columns, all parts may be substituted with equivalents.

Table 1. TPS7A39EVM-865 BOM(1)(2)(3)(4)

Designator Qty Value Description Package

Reference Part Number Manufacturer Alternate Part

Number Alternate

Manufacturer

!PCB1 1 Printed Circuit Board PWR865 Any - -

C1, C3, C8, C12 4 10uF CAP, CERM, 10 µF, 50 V, + /- 10%, X7 S, 1210 1210 C3225X7 S1 H106K250AB TDK

C6 1 0.1uF CAP, CERM, 0.1 µF, 100 V, + /- 10%, X7 S, AEC-Q200

Grade 1, 0603 0603 CGA3E3X7 S2A104K080AB TDK

C7, C10, C11 3 0.01uF CAP, CERM, 0.01 µF, 50 V, + /- 5%, C0 G/NP0, 0603 0603 C1608 NP01 H103 J080AA TDK

J2, J8 2 Standard Banana Jack, Insulated, Red 6091 6091 Keystone

J5, J6, J12, J13 4 Standard Banana Jack, Insulated, Black 6092 6092 Keystone

J9 1 Header, 2.54 mm, 4x2, Gold, SMT Header, 2.54

mm, 4x2, SMT TSM-104-01-L-DV Samtec

J10, J11 2 BANANA JACK, 15A, Insulated, Nylon, Yellow 940x438x438 mil 108-0907-001 Emerson Network Power

J14 1 Header, 100 mil, 3x1, Gold, SMT Samtec_TSM-

103-01-X-SV TSM-103-01-L-SV Samtec

J15 1 Header, 2.54 mm, 2x1, Gold, R/A, SMT Header, 2.54

mm, 2x1, R/A,

SMT 0878980204 Molex

J16 1 Header, 2.54 mm, 5x2, Gold, SMT Header, 2.54

mm, 5x2, SMT TSM-105-01-L-DV Samtec

R1 1 76.8k RES, 76.8 k, 1%, 0.1 W, 0603 0603 CRCW060376K8FKEA Vishay-Dale

R2 1 21.5k RES, 21.5 k, 1%, 0.1 W, 0603 0603 CRCW060321K5FKEA Vishay-Dale

R3 1 13.0k RES, 13.0 k, 1%, 0.1 W, 0603 0603 CRCW060313K0FKEA Vishay-Dale

R4 1 10.2k RES, 10.2 k, 1%, 0.1 W, 0603 0603 CRCW060310K2FKEA Vishay-Dale

R5 1 249k RES, 249 k, 1%, 0.1 W, 0603 0603 CRCW0603249KFKEA Vishay-Dale

R6, R9 2 280k RES, 280 k, 1%, 0.1 W, 0603 0603 CRCW0603280KFKEA Vishay-Dale

R7 1 0 RES, 0, 5%, 0.1 W, 0603 0603 ERJ-3 GEY0R00 V Panasonic

R8 1 100k RES, 100 k, 1%, 0.1 W, 0603 0603 CRCW0603100KFKEA Vishay-Dale

R10 1 66.5k RES, 66.5 k, 1%, 0.1 W, 0603 0603 CRCW060366K5FKEA Vishay-Dale

R11 1 22.1k RES, 22.1 k, 1%, 0.1 W, 0603 0603 CRCW060322K1FKEA Vishay-Dale

R12 1 14.0k RES, 14.0 k, 1%, 0.1 W, 0603 0603 CRCW060314K0FKEA Vishay-Dale

R13 1 11.0k RES, 11.0 k, 1%, 0.1 W, 0603 0603 CRCW060311K0FKEA Vishay-Dale

SH-J1, SH-J2, SH-

J3 3 1x2 Shunt, 100 mil, Gold plated, Black Shunt 969102-0000-DA 3M SNT-100-BK-G Samtec

Bill of Materials

www.ti.com

10 SBVU034–July 2017

Submit Documentation Feedback

TPS7A39EVM-865 Evaluation Module

Table 1. TPS7A39EVM-865 BOM(1)(2)(3)(4) (continued)

Designator Qty Value Description Package

Reference Part Number Manufacturer Alternate Part

Number Alternate

Manufacturer

TP1, TP2, TP3,

TP4, TP5, TP6,

TP7, TP8, TP9,

TP10, TP11, TP12

12 Test Point, Compact, SMT Testpoint_Keysto

ne_Compact 5016 Keystone

U1 1 Wide-VIN (±33 V), 150-mA, Spilt-Rail Output, Positive

and Negative LDO Voltage Regulator with Startup

Tracking, DSC0010 J DSC0010 J TPS7A3901DSC Texas Instruments

C2, C4, C9, C13 0 10uF CAP, CERM, 10 µF, 25 V, + /- 20%, X5R, 0603 0603 C1608X5R1E106M080AC TDK

C5 0 0.01uF CAP, CERM, 0.01 µF, 50 V, + /- 5%, C0 G/NP0, 0603 0603 C1608 NP01 H103 J080AA TDK

C14 0 0.1uF CAP, CERM, 0.1 µF, 100 V, + /- 10%, X7 S, AEC-Q200

Grade 1, 0603 0603 CGA3E3X7 S2A104K080AB TDK

D1, D2 0 60 V Diode, Schottky, 60 V, 1 A, SOD-123 SOD-123 RB160M-60 TR Rohm

FID1, FID2, FID3 0 Fiducial mark. There is nothing to buy or mount. Fiducial N/A N/A

J1, J3, J4, J7 0 Connector, SMA Jack, Vertical, Gold, SMD SMA 142-0711-201 Emerson Network Power

Table des matières

Autres manuels Texas Instruments Carte mère

Texas Instruments

Texas Instruments TLV320AIC1103 Manuel utilisateur

Texas Instruments

Texas Instruments LM5175EVM-HP Manuel utilisateur

Texas Instruments

Texas Instruments AFEDRI8201EVM Manuel utilisateur

Texas Instruments

Texas Instruments LM63635DNEVM Manuel utilisateur

Texas Instruments

Texas Instruments TPS22921 Manuel utilisateur

Texas Instruments

Texas Instruments DAC7554 Manuel utilisateur

Texas Instruments

Texas Instruments PGA281EVM Manuel utilisateur

Texas Instruments

Texas Instruments AFE5818 Manuel utilisateur

Texas Instruments

Texas Instruments PCM6 0Q1EVM-PDK Series Manuel utilisateur

Texas Instruments

Texas Instruments LMH2832EVM-50 Manuel utilisateur

Texas Instruments

Texas Instruments TUSB1142 Manuel utilisateur

Texas Instruments

Texas Instruments TPA3223EVM Manuel utilisateur

Texas Instruments

Texas Instruments INA232EVM Manuel utilisateur

Texas Instruments

Texas Instruments bq24720 EVM Manuel utilisateur

Texas Instruments

Texas Instruments INA2290EVM Manuel utilisateur

Texas Instruments

Texas Instruments INA2180-2181 Manuel utilisateur

Texas Instruments

Texas Instruments LMR36506MSCEVM Manuel utilisateur

Texas Instruments

Texas Instruments TMP75BEVM Manuel utilisateur

Texas Instruments

Texas Instruments CDCE62005EVM Manuel utilisateur

Texas Instruments

Texas Instruments TPS3847085EVM-577 Manuel utilisateur

Texas Instruments

Texas Instruments TPS7H5001-SP Manuel utilisateur

Texas Instruments

Texas Instruments TPS546D24SEVM-2PH Manuel utilisateur

Texas Instruments

Texas Instruments DAC53204EVM Manuel utilisateur

Texas Instruments

Texas Instruments AM263 Series Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur