Texas Instruments TPS51385EVM Manuel utilisateur
EVM User's Guide: TPS51385EVM
TPS51385 Step-Down Converter Evaluation Module
Description
The TPS51385 is a single, D-CAP3™ control mode,
synchronous buck converter requiring a very low
external component count. TPS51385EVM is a fully
assembled and tested circuit for evaluating the
TPS51385 converter. This EVM operates typical 12-V
input, and provides a 5.1-V output at 7-A.
Features
• 4.5-V to 24-V input voltage range
• 0.6-V to 5.5-V output voltage range
• Support 7-A continuous output current
• Selectable PSM and OOA mode under light load
• Fast load transient response
Applications
•Notebook and PC computers
•Ultrabook, tablet computers
•TV , STB
• Distributed power systems
Top View of TPS51385EVM
www.ti.com Description
SLUUCX3 – AUGUST 2023
Submit Document Feedback
TPS51385 Step-Down Converter Evaluation Module 1
Copyright © 2023 Texas Instruments Incorporated
1 Evaluation Module Overview
1.1 Introduction
The TPS51385 evaluation module (EVM) is a single, synchronous buck converter providing 5.1-V at 7-A from a
6-V to 24-V input. This user’s guide describes the TPS51385EVM performance.
Table 1-1. Input Voltage and Output Current Summary
EVM Input Voltage (VIN) Range Output Current (IOUT) Range
TPS51385EVM 6 V to 24 V 0 A to 7 A
This user's guide describes the characteristics, operation, and use of the Texas Instruments TPS51385
evaluation module (EVM). The TPS51385EVM is designed to help user easily evaluate and test the operation
and functionality of the TPS51385. This user's guide includes the following:
• Setup instructions for the hardware
• Printed-circuit board layouts for the EVM
• Schematic diagram
• Bills of material
• Test results for the EVM
1.2 Kit Contents
• One TPS51385EVM board
• EVM disclaimer Read Me
1.3 Specification
A summary of the TPS51385EVM performance specifications is provided in Table 1-2. Specifications are given
for 12-V input voltage and 5.1-V output voltage, unless otherwise noted. The ambient temperature is 25°C for all
measurement, unless otherwise noted.
Table 1-2. TPS51385EVM Performance Specifications Summary
Specifications Test Conditions MIN TYP MAX Unit
VIN Input voltage 6 12 24 V
CH1
Output voltage 5.1 V
Operating frequency VIN = 12 V, IOUT = 7 A 1000 kHz
Output current range 0 7 A
Overcurrent limit VIN = 12 V, LOUT = 1 µH 8.8 A
Output ripple voltage VIN = 12 V, IOUT = 7 A 20 mVPP
1.4 Device Information
TPS51385 is the main device on the EVM board. The TPS51385 is a single, D-CAP3™ control mode,
synchronous buck converter requiring a very low external component count. Features include an accurate
reference voltage, fast load transient response, auto-skip mode operation for light load efficiency, OOA light load
operation with > 25-kHz switching frequency, D-CAP3control mode with good line, load regulation, and does not
require external compensation.
Evaluation Module Overview www.ti.com
2TPS51385 Step-Down Converter Evaluation Module SLUUCX3 – AUGUST 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
2 Hardware
2.1 Input and Output Connections
The TPS51385EVM is provided with input and output connectors and test points as shown in Table 2-1. Test
point TP2 provides a place to monitor the VIN input voltages with TP9 providing a convenient ground reference.
TP5 is used to monitor the output voltage with TP12 as the ground reference.
Table 2-1. Connection and Test Points
Reference
Designator Function
J1 VIN (see Table 1-1 for VIN range)
J2 VOUT, 5.1 V at 7-A maximum
JP1 PG pullup control. Short pin 1 and pin 2 to pull PG up to VCC.
JP2 EN high control. Short pin 1 and pin 2 to connect VIN to pin 1 of JP3.
JP3 EN control. Short pin 1 and pin 2 of JP2 to make EN high.
JP4 Mode control. Float or short pin 2 and pin 3 to set PSM mode. Short pin 2 and
pin 1 to set OOA mode.
TP1 VIN positive monitor point
TP2 VIN positive test point
TP3 Switch node (SW) test point
TP4 VOUT positive monitor point
TP5 VOUT positive test point
TP6 EN test point
TP7 PG test point
TP8 GND monitor point
TP9 GND test point
TP10 GND monitor point
TP11 Loop test point
TP12 GND test point
TP13 VCC test point
TP14, TP15, TP16 GND test point
2.2 Modifications
The evaluation module is designed to provide access to the features of the TPS51385. Some modifications can
be made to this module.
2.2.1 Output Voltage Setpoint
To change the output voltage of the EVM, change the value of resistor R4 (Rupper) and R6 (Rlower). The value of
R4 and R6 for a specific output voltage can be calculated using Equation 1.
)
R
R
1(6.0V
LOWER
UPPER
OUT u
(1)
2.2.2 Mode Selection
TPS51385 has a MODE pin that can offer two different options of light load performance, as shown in Table 2-2.
Table 2-2. MODE Pin Settings
MODE Pin Light Load Performance
Connect Pin2(MODE) to Pin3(L) of JP4 or leave MODE pin floating PSM
Connect Pin2(MODE) to Pin1(H) of JP4 OOA
www.ti.com Hardware
SLUUCX3 – AUGUST 2023
Submit Document Feedback
TPS51385 Step-Down Converter Evaluation Module 3
Copyright © 2023 Texas Instruments Incorporated
3 Implementation Results
This section describes how to properly connect, set up, and use the TPS51385EVM. The section also includes
test results typical for the evaluation modules.
3.1 Evaluation Setup
1. Make sure that the jumper at JP2 (Enable High Control) is covered to connect VIN to pin 1 of JP3. Also
make sure JP3 (Enable Control) pin 2 and 3 are covered to shunt EN to GND to disable the output.
2. Apply appropriate input voltage to VIN (J1-1) or TP1 and GND (J1-2) or TP8. Connect a power supply
capable of supplying 7-A to J1 through a pair of 20AWG wires. Note that the board cannot support hot
plug-in. The input lines must be connected between J1 and an external power source first before turning on
the power source.
3. Move the jumper at JP3 (Enable Control) from pin 2 and 3 (EN and OFF) to pin 2 and 1 (EN and ON) and
make sure JP2 pin 1 and pin 2 are covered. Then, the output can be enabled.
4. Apply the loading to VOUT (J2-2) or TP4 and GND (J2-1) or TP10. The load must be connected to J2
through a pair of 20AWG wires. The maximum load current capability is 7 A. Minimize wire lengths to reduce
losses in the wires.
3.2 Test Setup and Results
3.2.1 Start-Up
The following figures show the TPS51385EVM start-up waveform relative to EN.
VOUT=2V/div
PG=5V/div
IL=2A/div
EN=5V/div
Figure 3-1. Start-Up Relative to EN, IOUT = 0.1 A (2ms/div)
Implementation Results www.ti.com
4TPS51385 Step-Down Converter Evaluation Module SLUUCX3 – AUGUST 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
VOUT=2V/div
PG=5V/div
IL=5A/div
EN=5V/div
Figure 3-2. Start-Up Relative to EN, IOUT = 7 A (2ms/div)
3.2.2 Shutdown
The following figures show the TPS51385EVM shutdown waveform relative to EN.
VOUT=2V/div
PG=5V/div
IL=2A/div
EN=5V/div
Figure 3-3. Shutdown Relative to EN, IOUT = 0.1 A (2ms/div)
VOUT=2V/div
PG=5V/div
IL=5A/div
EN=5V/div
Figure 3-4. Shutdown Relative to EN, IOUT = 7 A (2ms/div)
www.ti.com Implementation Results
SLUUCX3 – AUGUST 2023
Submit Document Feedback
TPS51385 Step-Down Converter Evaluation Module 5
Copyright © 2023 Texas Instruments Incorporated
3.2.3 Output Voltage Ripple
The following images show the TPS51385EVM output voltage ripple.
VOUT=20mV/div (AC coupled)
SW=5V/div
Figure 3-5. TPS51385EVM Output Voltage Ripple, IOUT = 10 mA, PSM Mode (100us/div)
VOUT=20mV/div (AC coupled)
SW=5V/div
Figure 3-6. TPS51385EVM Output Voltage Ripple, IOUT = 10 mA, OOA Mode (10us/div)
VOUT=20mV/div (AC coupled)
SW=5V/div
Figure 3-7. TPS51385EVM Output Voltage Ripple, IOUT = 7 A (1us/div)
Implementation Results www.ti.com
6TPS51385 Step-Down Converter Evaluation Module SLUUCX3 – AUGUST 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
4 Hardware Design Files
4.1 Schematic
The following image shows the schematic for the TPS51385EVM.
Figure 4-1. TPS51385EVM Schematic Diagram
www.ti.com Hardware Design Files
SLUUCX3 – AUGUST 2023
Submit Document Feedback
TPS51385 Step-Down Converter Evaluation Module 7
Copyright © 2023 Texas Instruments Incorporated
4.2 PCB Layout
The following figures show the board layout for the TPS51385EVM. TPS51385EVM is with four layers. The top
layer contains the main power traces for VIN, VOUT, and GND. Also on the top layer are connections for the pins
of the TPS51385 and a large area filled with ground. Most of the signal traces are also located on the top side.
The input decoupling capacitors C4, C5, and C6 are located as close to VIN pins and PGND pins of the IC as
possible. The input and output connectors, test points, and all of the components are located on the top side.
The bottom layer is a ground plane along with signal ground copper fill and the feedback trace from the point of
regulation to the top of the resistor divider network. Two inner layers are ground plane.
Figure 4-2. Top Assembly
Figure 4-3. Top Layer
Hardware Design Files www.ti.com
8TPS51385 Step-Down Converter Evaluation Module SLUUCX3 – AUGUST 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
4.3 Bill of Materials
The following table displays the TPS51385EVM bill of materials.
Table 4-1. Bill of Materials
Designator Qty Description Part Number Manufacturer(1)
C1, C6 2 CAP, CERM, 0.1 µF, 25 V, ±10%, X5R, 0603 CL10A104KA8NNNC Samsung Electro-
Mechanics
C4, C5 2 CAP, CERM, 10 μF, 35 V, ±10%, X5R, 0805 GRM21BR6YA106KE43L MuRata
C7, C8, C9 3 CAP, CERM, 22 μF, 10 V, ±20%, X5R, 0805 GRM21BR61A226ME44L MuRata
C12 1 CAP, CERM, 22 pF, 50 V, ±5%, C0G/NP0, 0603 C0603C220J5GACTU Kemet
C13 1 CAP, CERM, 1 μF, 10 V, ±10%, X5R, 0603 C0603C105K8PACTU Kemet
C14 1 CAP, CERM, 0.022 μF, 16 V, ±10%, X7R, 0603 C0603C220J5GACTU Kemet
C15 1 CAP, CERM, 0.01 μF, 16 V, ±10%, X7R, 0603 C0603C103K4RACTU Kemet
D1 1 Diode, Zener, 5.1 V, 200 mW, SOD-323 MMSZ5231BS-7-F Diodes Inc.
H1, H2, H3,
H4 4 Bumpon, Hemisphere, 0.44 × 0.20, Clear SJ-5303 (CLEAR) 3M
J1, J2 2 Terminal Block, 5.08 mm, 2 × 1, Brass, TH ED120/2DS On-Shore Technology
JP1, JP2 2 Header, 100mil, 2 × 1, Gold, TH PBC02SAAN Sullins Connector Solutions
JP3, JP4 2 Header, 100mil, 3 × 1, Tin, TH PEC03SAAN Sullins Connector Solutions
L1 1 Inductor, 1 μH, 14.4 A, 0.0064 Ω, SMD CMLE063T-1R0MS Cyntec
LBL1 1 Thermal Transfer Printable Labels, 1.250" W × 0.250" H
– 10,000 per roll THT-13-457-10 Brady
R1, R5 2 RES, 0, 5%, 0.1 W, 0603 RC0603JR-070RL Yageo
R2 1 RES, 51, 5%, 0.1 W, AEC-Q200 Grade 0, 0603 CRCW060351R0JNEA Vishay-Dale
R3 1 RES, 100 k, 5%, 0.1 W, 0603 CRCW0603100KJNEAC Vishay-Dale
R4 1 RES, 150 k, 1%, 0.1 W, 0603 RC0603FR-07150KL Yageo
R6 1 RES, 20.0 k, 1%, 0.1 W, AEC-Q200 Grade 0, 0603 ERJ-3EKF2002V Panasonic
R7, R8, R9 3 RES, 20.0 k, 1%, 0.1 W, AEC-Q200 Grade 0, 0603 CRCW060320K0FKEA Vishay-Dale
SH-JP1, SH-
JP2, SH-JP3,
SH-JP4
4 Shunt, 100 mil, Gold plated, Black SNT-100-BK-G Samtec
TP1, TP4,
TP8, TP10 4 Terminal, Turret, TH, Triple 1598-2 Keystone
TP2, TP3,
TP5, TP6,
TP7, TP11,
TP13
7 Test Point, Miniature, Red, TH 5000 Keystone
TP9, TP12,
TP14, TP15,
TP16
5 Test Point, Miniature, Black, TH 5001 Keystone
U1 1 4.5-V to 24-V Input, 7-A Synchronous Buck Converter TPS51385RJNR Texas Instruments
C2, C3 0 CAP, CERM, 10 μF, 35 V, ±10%, X5R, 0805 GRM21BR6YA106KE43L MuRata
C10, C11 0 CAP, CERM, 22 μF, 10 V, ±20%, X5R, 0805 GRM21BR61A226ME44L MuRata
(1) Unless otherwise noted in the Alternate Part Number or Alternate Manufacturer columns, all parts can be substituted with equivalents.
Hardware Design Files www.ti.com
10 TPS51385 Step-Down Converter Evaluation Module SLUUCX3 – AUGUST 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Texas Instruments Carte mère
Texas Instruments
Texas Instruments TLC5944EVM-358 Manuel utilisateur
Texas Instruments
Texas Instruments BQ75614-Q1 Manuel utilisateur
Texas Instruments
Texas Instruments LMX2572EVM Manuel utilisateur
Texas Instruments
Texas Instruments TPS65053EVM-389 Manuel utilisateur
Texas Instruments
Texas Instruments TLV841EVM Manuel utilisateur
Texas Instruments
Texas Instruments ADC32RF-EVM Series Manuel utilisateur
Texas Instruments
Texas Instruments LM5185-Q1 Manuel utilisateur
Texas Instruments
Texas Instruments TMAG6180-6181EVM Manuel utilisateur
Texas Instruments
Texas Instruments ADS8688EVM-PDK Manuel utilisateur
Texas Instruments
Texas Instruments ADS5294EVM Manuel utilisateur
Texas Instruments
Texas Instruments Stellaris LM3S6965 Manuel utilisateur
Texas Instruments
Texas Instruments TLV62080 Manuel utilisateur
Texas Instruments
Texas Instruments THS1206EVM Manuel utilisateur
Texas Instruments
Texas Instruments SmartRF06 Manuel utilisateur
Texas Instruments
Texas Instruments LM3000 Manuel utilisateur
Texas Instruments
Texas Instruments TMS320DM644 Series Manuel utilisateur
Texas Instruments
Texas Instruments TPS7H2211EVM Manuel utilisateur
Texas Instruments
Texas Instruments TAS5825P Manuel utilisateur
Texas Instruments
Texas Instruments DRV632EVM Manuel utilisateur
Texas Instruments
Texas Instruments TPS3840EVM Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
Biostar
Biostar M7VIT Bravo Instructions d'utilisation et d'installation
