Texas Instruments SMALL-AMP-DIP Manuel utilisateur
1
SBOU215–January 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
SMALL-AMP-DIP Evaluation Module (EVM)
User's Guide
SBOU215–January 2019
SMALL-AMP-DIP Evaluation Module (EVM)
This user’s guide contains support documentation for the SMALL-AMP-DIP evaluation module (EVM).
Included is a step-by-step guide on setting up and configuring the EVM, bill of materials (BOM), and
printed circuit board (PCB) layout.
Contents
1 Introduction ................................................................................................................... 3
2 Hardware Setup.............................................................................................................. 4
3 EVM Description and PCB Layout......................................................................................... 7
4 Bill of Materials and References ......................................................................................... 10
List of Figures
1 Location of packages on EVM............................................................................................. 4
2 Detach desired PCB......................................................................................................... 5
3 Detached PCB with soldered IC........................................................................................... 5
www.ti.com
2SBOU215–January 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
SMALL-AMP-DIP Evaluation Module (EVM)
4 Terminal strip (TS-132-G-AA) broken into 4 position length........................................................... 5
5 Terminal strip (TS-132-G-AA) inserted into spare DIP socket......................................................... 6
6 Fully assembled PCB ....................................................................................................... 6
7 DPW package top layer (left) and bottom layer (right) PCB layout ................................................... 7
8 DSG package top layer (left) and bottom layer (right) PCB layout.................................................... 7
9 DCN and DDF packages top layer (left) and bottom layer (right) PCB layout....................................... 7
10 RUG package top layer (left) and bottom layer (right) PCB layout.................................................... 8
11 RUC package top layer (left) and bottom layer (right) PCB layout.................................................... 8
12 RGY package top layer (left) and bottom layer (right) PCB layout.................................................... 9
13 RTE package top layer (left) and bottom layer (right) PCB layout .................................................... 9
List of Tables
1 Package type mapped to EVM............................................................................................. 4
Trademarks
All trademarks are the property of their respective owners.
www.ti.com
Introduction
3
SBOU215–January 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
SMALL-AMP-DIP Evaluation Module (EVM)
1 Introduction
The SMALL-AMP-DIP-EVM is designed to facilitate evaluation of op amps offered in small packages. This
EVM gives users an easy tool to test the following op amp packages: DPW, DCN, DDF, DSG, RUG, RUC,
RGY, and RTE. This EVM routes each pin of the device to a header pin and can be used as a basic
building block for circuit design and device testing purposes.
1.1 List of Packages
The SMALL-AMP-DIP-EVM contains the following packages:
• DPW-5
• DCN-8
• DDF-8
• DSG-8
• RUG-10
• RUC-14
• RGY-14
• RTE-16
Hardware Setup
www.ti.com
4SBOU215–January 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
SMALL-AMP-DIP Evaluation Module (EVM)
2 Hardware Setup
The SMALL-AMP-DIP-EVM setup requires identifying and breaking out the desired PCB from the EVM
and then soldering the IC and terminal strips onto the EVM. This section presents the details of these
procedures.
2.1 EVM Package Locations
Figure 1 and Table 1 map the location of each package on the EVM. Figure 1 labels each package
drawing with a letter ranging from A to G. Table 1 matches the package drawing to a letter in Figure 1.
Figure 1. Location of packages on EVM
Table 1. Package type mapped to EVM
Package Name Letter in Figure 1
DPW-5 A
DCN-8 B
DDF-8 B
DSG-8 C
RUG-10 D
RUC-14 E
RGY-14 F
RTE-16 G
www.ti.com
Hardware Setup
5
SBOU215–January 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
SMALL-AMP-DIP Evaluation Module (EVM)
2.2 EVM Assembly Instructions
This section provides step-by-step instructions on how to assemble the EVM.
1. Choose the desired package. See Section 2.1 for the location of each package type.
2. Gently flex the PCB panel at the score lines to separate the desired package from the EVM.
Figure 2. Detach desired PCB
3. Solder the device onto the separated PCB.
Figure 3. Detached PCB with soldered IC
4. Use long-nose pliers to snap terminal header strips into the desired position lengths.
• For the DPW, DCN, DDF and DSG packages, the terminal strips need to be snapped into 4
position lengths, as shown in Figure 4.
• For the RUG package, use 5 position lengths.
• For the RUC and RGY packages, use 7 position lengths.
• And for the RTE package, use 8 position lengths.
Figure 4. Terminal strip (TS-132-G-AA) broken into 4 position length
Hardware Setup
www.ti.com
6SBOU215–January 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
SMALL-AMP-DIP Evaluation Module (EVM)
5. Insert the header strips into a spare DIP socket or breadboard as shown in Figure 5.
Figure 5. Terminal strip (TS-132-G-AA) inserted into spare DIP socket
6. Position the separated PCB with the soldered IC over the terminal strips and solder each pin in
place. Carefully remove the PCB from the DIP socket. Figure 6 displays a fully assembled PCB.
Figure 6. Fully assembled PCB
www.ti.com
EVM Description and PCB Layout
7
SBOU215–January 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
SMALL-AMP-DIP Evaluation Module (EVM)
3 EVM Description and PCB Layout
This section shows the PCB layout of each circuit configuration provided on the EVM.
3.1 DPW Package
Figure 7 displays the PCB layout of the top (left) and bottom layers (right) for the DPW package.
Figure 7. DPW package top layer (left) and bottom layer (right) PCB layout
The X2SON (DPW) package has the following dimensions: 0.48-mm pitch, 0.37-mm maximum height, 0.8-
mm length, and 0.8-mm width.
3.2 DSG Package
Figure 8 displays the PCB layout of the top (left) and bottom layers (right) for the DSG package.
Figure 8. DSG package top layer (left) and bottom layer (right) PCB layout
The WSON (DSG) package has the following dimensions: 0.5-mm pin pitch, 0.75-mm maximum height,
2.0-mm length, and 2.0-mm width.
3.3 DCN and DDF Packages
Figure 9 displays the PCB layout of the top (left) and bottom layers (right) for the DCN and DDF
packages.
Figure 9. DCN and DDF packages top layer (left) and bottom layer (right) PCB layout
The SOT-23 (DCN and DDF) package has the following dimensions: 0.65-mm pin pitch, 1.1-mm maximum
height, 2.9-mm length, and 1.63-mm width.
EVM Description and PCB Layout
www.ti.com
8SBOU215–January 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
SMALL-AMP-DIP Evaluation Module (EVM)
3.4 RUG Package
Figure 10 displays the PCB layout of the top (left) and bottom layers (right) for the RUG package.
Figure 10. RUG package top layer (left) and bottom layer (right) PCB layout
The X2QFN (RUG) package has the following dimensions: 0.5-mm pin pitch, 0.37-mm maximum height,
1.5-mm length, and 2.0-mm width.
3.5 RUC Package
Figure 11 displays the PCB layout of the top (left) and bottom layers (right) for the RUC package.
Figure 11. RUC package top layer (left) and bottom layer (right) PCB layout
The X2QFN (RUC) package has the following dimensions: 0.4-mm pin pitch, 0.35-mm maximum height,
2.0-mm length, and 2.0-mm width
www.ti.com
EVM Description and PCB Layout
9
SBOU215–January 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
SMALL-AMP-DIP Evaluation Module (EVM)
3.6 RGY Package
Figure 12 displays the PCB layout of the top (left) and bottom layers (right) for the RGY package.
Figure 12. RGY package top layer (left) and bottom layer (right) PCB layout
The VQFN (RGY) package has the following dimensions: 0.5-mm pin pitch, 0.9-mm maximum height, 3.5-
mm length, and 3.5-mm width.
3.7 RTE Package
Figure 13 displays the PCB layout of the top (left) and bottom layers (right) for the RTE package.
Figure 13. RTE package top layer (left) and bottom layer (right) PCB layout
The WQFN (RTE) package has the following dimensions: 0.5-mm pin pitch, 0.75-mm maximum height,
3.0-mm length, and 3.0-mm width.
Bill of Materials and References
www.ti.com
10 SBOU215–January 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
SMALL-AMP-DIP Evaluation Module (EVM)
4 Bill of Materials and References
4.1 Bill of Materials
Designator QTY Description Part Number
PCB 1 Printed-Circuit-Board SMALL-AMP-DIP-EVM
Header Strips 2 Header, 2.54 mm, 32 × 1,
Gold, TH TS-132-G-AA
4.2 References
(1) DIYAMP-EVM Tool Folder
(2) DUAL-DIYAMP-EVM Tool Folder
(3) DIP Adapter EVM Tool Folder
(4) TI Precision Labs Training
Table des matières
Autres manuels Texas Instruments Carte mère
Texas Instruments
Texas Instruments LMH1297EVM Manuel utilisateur
Texas Instruments
Texas Instruments AM263 Series Manuel utilisateur
Texas Instruments
Texas Instruments DLP5534PROJQ1EVM Manuel utilisateur
Texas Instruments
Texas Instruments MCT8316A Guide de démarrage rapide
Texas Instruments
Texas Instruments LM74704Q1EVM Manuel utilisateur
Texas Instruments
Texas Instruments ADC3 J EVM Series Manuel utilisateur
Texas Instruments
Texas Instruments LP5860TEVM Manuel utilisateur
Texas Instruments
Texas Instruments BQ25720 Manuel utilisateur
Texas Instruments
Texas Instruments TPS54225 Manuel utilisateur
Texas Instruments
Texas Instruments TMAG5328EVM Manuel utilisateur
Texas Instruments
Texas Instruments TPA6020A2 Manuel utilisateur
Texas Instruments
Texas Instruments DEM-DSD1796 Manuel utilisateur
Texas Instruments
Texas Instruments Tiva TM4C123G Manuel utilisateur
Texas Instruments
Texas Instruments LM10010 Manuel utilisateur
Texas Instruments
Texas Instruments TPS71401DRVEVM-426 Manuel utilisateur
Texas Instruments
Texas Instruments ADS1271EVM-PDK Manuel utilisateur
Texas Instruments
Texas Instruments TPS7A87 Manuel utilisateur
Texas Instruments
Texas Instruments ADS7861EVM Manuel utilisateur
Texas Instruments
Texas Instruments DS90UB96X-Q1EVM Manuel utilisateur
Texas Instruments
Texas Instruments TPS7A74EVM-068 Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
Biostar
Biostar M7VIT Bravo Instructions d'utilisation et d'installation
