Texas Instruments HDC1050EVM Manuel utilisateur
HDC1050EVM User 's Guide
User's Guide
Literature Number: SNAU181A
June 2015–Revised June 2015
User's Guide
SNAU181A–June 2015–Revised June 2015
HDC1050EVM User 's Guide
1 Introduction
The Texas Instruments HDC1050EVM evaluation module (EVM) enables designers to evaluate the
operation and performance of the HDC1050 Relative Humidity and Temperature sensor.
The EVM contains one HDC1050 (See Table 1).
Table 1. Device and Package Configurations
DEVICE IC PACKAGE
U1 HDC1050 PWSON 6pin
The EVM hosts an MSP430F5528 microcontroller (µC) as well as the HDC1050. The µC is used to control
the HDC1050 and communicate with a host PC through a USB port. The EVM is designed to be broken
into two sections if desired. The sensor section can be separated from the µC section so that the user can
remotely locate the sensor from the µC section.
2 Setup
This section describes the connectors on the EVM as well and how to properly connect, set up and use
the HDC1050EVM.
Figure 1. HDC1050EVM
2HDC1050EVM User 's Guide SNAU181A–June 2015–Revised June 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com
Setup
2.1 Input/Output Connector Description
2.1.1 J1 – 5x1 Header
This header is not populated and can be installed if the EVM is broken in 2 sections: PC interface and
Sensor. This connector with its counterpart J2 allows the communication of the two sections through a 4-
wire cable.
Pin out:
• J1.1 GND
• J1.2 SDA
• J1.3 SCL
• J1.4 DRDYn (NOTE: this signal is not supported by the HDC1050, and does not need to be
connected to a host controller)
• J1.5 VDD
2.1.2 J2 – 5x1 Header
This header is not populated and can be installed if the EVM is broken in 2 sections: PC interface and
Sensor. This connector with its counterpart J1 allows the communication of the two sections through a 5-
wire cable.
Pin out:
• J2.1 GND
• J2.2 SDA
• J2.3 SCL
• J2.4 DRDYn (NOTE: this signal is not supported by the HDC1050n and does not need to be
connected)
• J2.5 VDD
2.1.3 J3 – USB Type A Connector
This connector is used for communications with the PC and provides power for the EVM.
2.2 Hardware Setup
The HDC1050EVM power is supplied via the USB connector. The LDO (U4) converts the 5V from the
USB to 3.3V used by the HDC1050 and the MSP430. The EVM may be directly inserted into a USB port
on a PC or laptop, or may be connected to the latter using the appropriate USB cable.
The I2C address of the HDC1050 is 1000000xb and is fixed by design.
The EVM features a Spy-by-Wire interface to the MSP430 that enables custom firmware development and
debug using Code Composer Studio ©.
2.3 Software Setup
2.3.1 System Requirements
The Sensing Solutions GUI supports:
• 64-bit Windows 7
• 64-bit Windows XP
The current GUI does not support 32-bit Windows operating systems. The host machine is required for
device configuration and data streaming. The following steps are necessary to prepare the EVM for the
GUI:
• The GUI and EVM driver must be installed on the host.
• The EVM must be connected to a full speed USB port (USB 1.0 or above).
3
SNAU181A–June 2015–Revised June 2015 HDC1050EVM User 's Guide
Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated
Setup
www.ti.com
2.3.2 Sensing Solutions GUI and EVM Driver Installation
The Sensing Solutions GUI and EVM driver installer is packaged in a zip file. Follow these steps to install
the software.
1. Download the software ZIP file from the EVM tool page
2. Extract the downloaded ZIP file
3. Run the included executable
4. Follow all directions from the installer
Figure 2. GUI Installer Welcome Page
5. Read the license agreement and if you still wish to install the software, select “I accept the agreement”
and click “Next” as shown in
4HDC1050EVM User 's Guide SNAU181A–June 2015–Revised June 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com
Setup
Figure 3. GUI Installer License Agreement
6. Select the installation directory. If the user installing the software is not a system administrator a
directory not with “Program Files” should be chosen instead of the default.
Figure 4. GUI Installer Installation Directory
7. Wait for all files to install
5
SNAU181A–June 2015–Revised June 2015 HDC1050EVM User 's Guide
Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated
Setup
www.ti.com
Figure 5. GUI Installer Copying Files
8. After the files have copied a device driver installer will start. If prompted about an unsigned driver,
choose to install the driver anyways. If running Windows 8 or 8.1, the PC must be started in a “Safe”
mode to install the unsigned driver.
Figure 6. EVM Driver Installer Welcome Page
9. Wait for the driver to install
6HDC1050EVM User 's Guide SNAU181A–June 2015–Revised June 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com
Setup
Figure 7. EVM Driver Installer In Progress
10. Click “Finish” after the driver has been installed
Figure 8. EVM Driver Installer Complete
11. Click “Finish” to complete the software installation
7
SNAU181A–June 2015–Revised June 2015 HDC1050EVM User 's Guide
Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated
www.ti.com
Setup
2.4 Operation
When the EVM is connected the host computer, the latter should automatically detect the device as an
HDC1050EVM/HDC1000EVM.
Launch the GUI. A detailed description of the GUI operation is presented later in this document.
2.5 Reducing the Sensor Thermal Mass
The HDC1050EVM can be broken into 2 sections to isolate the thermal mass of the µC from the
HDC1050. The yellow arrow in Figure 10 shows the board perforations that allow the two sections to be
broken apart.
Figure 10. HDC1050EVM µC and Sensor Sections
The communication between the two modules is achieved through the connectors J1 and J2 and a 4-wire
cable. In this configuration the thermal mass of the EVM is dramatically reduced, improving the
temperature measurement performance of the HDC1050. The cable connecting J1 to J2 must conform to
I2C cable length constraints. When used in this configuration, the GUI can still be used to communicate
with the EVM and collect data.
If the thermal mass of the sensor section is still excessive, the sensor section can be reduced by breaking
it at the perforation shown by the yellow arrow, indicated in Figure 11. The PCB segment that hosts the
HDC1050 is 5.5mm x 5mm.
Figure 11. HDC1050EVM Small Sensor Section
9
SNAU181A–June 2015–Revised June 2015 HDC1050EVM User 's Guide
Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated
GUI Operation
www.ti.com
The communications with the µC section is achieved through a 4-wire cable soldered at the pads
accessible on the bottom layer of the PCB (Refer to Figure 12).
Figure 12. HDC1050EVM Pads for I2C and Supply of the Smaller Sensor Section
3 GUI Operation
The section describes how to use the GUI
3.1 Starting the GUI
Follow these steps to start the GUI:
1. Select the windows start menu
2. Select “All programs”
3. Select the “Texas Instruments” folder
4. Select the Sensing Solutions GUI
5. Click “Sensing Solutions GUI”
6. Splash screen will appear for at least two seconds.
• Slower PC’s may show a blank splash screen without any texts for up to 20 seconds
10 HDC1050EVM User 's Guide SNAU181A–June 2015–Revised June 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Table des matières
Autres manuels Texas Instruments Carte mère
Texas Instruments
Texas Instruments BQ27620 Manuel utilisateur
Texas Instruments
Texas Instruments AM335 Series Manuel utilisateur
Texas Instruments
Texas Instruments TPS54KC23EVM Manuel utilisateur
Texas Instruments
Texas Instruments SN75LVCP600S Manuel utilisateur
Texas Instruments
Texas Instruments TPS53515EVM-PWR587 Manuel utilisateur
Texas Instruments
Texas Instruments LDC2114 Manuel utilisateur
Texas Instruments
Texas Instruments TPS6594-Q1 Series Manuel utilisateur
Texas Instruments
Texas Instruments WCSP-Packaged bq24272 Manuel utilisateur
Texas Instruments
Texas Instruments DS16EV51-AEVKD Manuel utilisateur
Texas Instruments
Texas Instruments DLP LightCrafter 160CP Manuel utilisateur
Texas Instruments
Texas Instruments TLV320AIC3104EVM Manuel utilisateur
Texas Instruments
Texas Instruments TPS53915EVM-PWR587 Manuel utilisateur
Texas Instruments
Texas Instruments BQ25883 Manuel utilisateur
Texas Instruments
Texas Instruments bq24261M Manuel utilisateur
Texas Instruments
Texas Instruments RS485-HF-DPLX-EVM Manuel utilisateur
Texas Instruments
Texas Instruments bq24295EVM-549 Manuel utilisateur
Texas Instruments
Texas Instruments DLP3021LEQ1EVM Manuel utilisateur
Texas Instruments
Texas Instruments bq2000EVM Manuel utilisateur
Texas Instruments
Texas Instruments Chipcon CC2400DBK Manuel utilisateur
Texas Instruments
Texas Instruments THS4131 Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
Biostar
Biostar M7VIT Bravo Instructions d'utilisation et d'installation
