Texas Instruments DRV8428E Manuel utilisateur

SLOU537–June 2020

DRV8428E EVM GUI User's Guide

User's Guide

SLOU537–June 2020

DRV8428E EVM GUI User's Guide

This document is provided with the DRV8428E evaluation module (EVM) as a supplement to DRV8428E

Stepper Motor Driver datasheet. This user's guide details on how to use the DRV8428E EVM GUI

application.

Contents

1 Overview...................................................................................................................... 2

2 Hardware and Software Setup............................................................................................. 2

3 GUI Application .............................................................................................................. 2

List of Figures

1 DRV8428E EVM GUI (Landing Page) .................................................................................... 3

2 DRV8428E EVM GUI (Home Page)....................................................................................... 4

3 DRV8428E EVM GUI (Device Connection Pane)....................................................................... 4

4 Serial Port Configuration.................................................................................................... 5

5 DRV8428E EVM GUI (Motor Control Page) ............................................................................. 6

6 Controls Available for Speed Mode ...................................................................................... 7

7 Controls Available for Step Mode.......................................................................................... 7

8 Stop Conditions.............................................................................................................. 8

9 DRV8428E EVM GUI (Decay Mode and TOFF setting)................................................................ 8

10 DRV8428E EVM GUI (Menu Bar – Help Option)........................................................................ 9

Trademarks

All trademarks are the property of their respective owners.

Overview

www.ti.com

2SLOU537–June 2020

Submit Documentation Feedback

DRV8428E EVM GUI User's Guide

1 Overview

The DRV8428E EVM is a platform to support prototyping and evaluation for the DRV8428E, a medium-

voltage dual H-bridge driver for stepper driving applications.

The EVM uses an MSP430™ microcontroller and a USB interface chip to manage communication from

the GUI software application installed on a PC computer with Windows®. The GUI sends serial

commands to the MSP430 to control the device signals, monitor faults, read and write SPI registers, and

drive a stepper motor by issuing the step commands at the desired rate. This document describes the

software and tools used to evaluate DRV8428E device for stepper motor driving on the DRV8428E EVM.

2 Hardware and Software Setup

The hardware (HW) and software (SW) tools that follow are required for the evaluation of DRV8428E:

• DRV8428E EVM

• Stepper motor

• Voltage supply from 4.2 to 33 V

This document only describes the installation and usage of the DRV8428E EVM GUI. For additional

details on hardware connections refer to the DRV8428xEVM User's Guide.

3 GUI Application

3.1 Installation

Installation (For Desktop Version Only)

• Download the installable DRV8428_x.x.x_installer_win.zip file (The file is inside the

DRV8428xEVM_software.zip file. x.x.x is the GUI revision number).

• Extract the zip.

• Double click on the installer to install the GUI application. During the first installation, the installer

prompts for installation of Cloud Agent. Please install it. During the installation, customer company's

firewall may block "download from website” option for the GUI composer runtime installation, please

download GUI runtime v7.4.1 from this link: https://software-dl.ti.com/ccs/non-

esd/gui_composer/runtime/gcruntime-7.4.1-windows-installer.exe and save it to your local harddrive.

And then, use "Install from File" option to install the GUI composer runtime.

3.2 Getting Started with DRV8428E EVM GUI

The DRV8428E EVM GUI and DRV8428E EVM allows the user to configure various settings required for

BDC motor or stepper motor driving. The DRV8428E EVM GUI lets the user adjust the motor speed,

control the direction, control the step movement, configure various device settings, and monitor the device

status.

Perform the following steps to begin using the GUI:

• Connect the stepper motor to the EVM.

• Plug in the micro-USB cable to the PC.

• Enable the motor power supply. For additional details on hardware connections refer to the

DRV8428xEVM User's Guide

Click on DRV8428E EVM GUI shortcut either on the desktop or from the start menu to run the GUI

application.

3.3 Use the DRV8428E EVM GUI

After open the DRV8428 GUI, the GUI landing page shown in Figure 1

www.ti.com

GUI Application

SLOU537–June 2020

DRV8428E EVM GUI User's Guide

Figure 1. DRV8428E EVM GUI (Landing Page)

After click the DRV8428E device from the GUI landing page, the DRV8428E GUI home page shown in

Figure 2

The application will try to establish communication with the device connected. A message showing

‘Connected to Cloud Agent. Connecting to target…’ will be displayed in the hardware connection status

pane at the bottom of the screen. If the connection is successful, ‘COMxx:9600 Connected to Target’

message appears as shown in Figure 3 below

GUI Application

www.ti.com

4SLOU537–June 2020

Submit Documentation Feedback

DRV8428E EVM GUI User's Guide

Figure 2. DRV8428E EVM GUI (Home Page)

Figure 3. DRV8428E EVM GUI (Device Connection Pane)

If the GUI fails to connect to the EVM, the hardware connection status pane will show the message

‘Hardware Not Connected’.

If the GUI is opened without connecting the EVM, the hardware connection status pane will show ‘Error:

no serial ports found’.

If there are more than one DRV8428E EVM boards connected, the first matching device will be connected

automatically. In order to switch to another EVM:

1. Click Options -> Serial Port. A serial port configuration popup is displayed as shown below in Figure 4.

2. Choose the appropriate port and baud rate.

3. Click OK

www.ti.com

GUI Application

SLOU537–June 2020

DRV8428E EVM GUI User's Guide

Figure 4. Serial Port Configuration

Once the correct device is connected, the home page will show a message ‘Device Connected’ with a

green check mark as shown in Figure 2

Click on the ‘Stepper Motor’ button to open the motor control page.

3.3.1 Motor Control Page

This page (shown in Figure 5) includes various controls to sleep/wake the driver and control the motor by

configuring various parameters such as AVREF_VALt, control mode and so forth. Hovering over the (?)

icon to the right of a control displays a brief description about the control.

GUI Application

www.ti.com

6SLOU537–June 2020

Submit Documentation Feedback

DRV8428E EVM GUI User's Guide

Figure 5. DRV8428E EVM GUI (Motor Control Page)

3.3.1.1 Control Modes

The GUI allows the user to control the stepper motion profile in two modes – Speed Mode and Step Mode.

To toggle between the modes, use the toggle button at the top of the screen.

3.3.1.1.1 Speed Mode

Speed Mode allows the user to spin the stepper motor continuously at a desired speed. The user

configures the starting speed, stopping speed, acceleration rate, and target speed. Stepper controls are

enabled only when ‘Motor Driver' control is enabled. ‘Start Steps’ button is enabled only when ‘Driver

Outputs' control is enabled for example, AEN and BEN pins are set to high. When the ‘Start Steps’ button

is clicked, the motor begins spinning at the starting speed and accelerates to the target speed according

to the configured acceleration rate. The acceleration profile in the microcontroller firmware accepts the

starting-speed PPS signal and target-speed PPS signal as a clock cycle number.

When the ‘Start steps’ button is clicked, the PWM timer generates steps at a rate specified by the 'Starting

Speed' PPS parameter. When ‘Stop Steps’ is clicked, the motor starts decelerating at the ‘Acceleration

Rate’ configured to reach the stopping speed and eventually stop. The configuration is visualized by the

embedded graph shown on the GUI screen.

When accelerating or decelerating, the PPS signal is adjusted every 32 ms based on the integer value of

PPSPS / 32 ms. Acceleration rates must be between 1 and 65,535 PPSPS. The step rate increases by

the calculated value until the target speed is reached.

The starting speed must be less than or equal to the target speed. If the starting speed and target speed

are equal, the EVM firmware will not perform an acceleration routine. The stopping speed must also be

less than or equal to the target speed. The target speed is limited to a range between 200 and 50,000

PPS.

www.ti.com

GUI Application

SLOU537–June 2020

DRV8428E EVM GUI User's Guide

The 'Start Steps' command computes how frequently automatic speed updates are issued and a second

timer is used to change the speed according to the programmed acceleration rate profile. Once clicked,

the motor will begin spinning according to the parameters set in the GUI.

When the target speed PPS value is reached, the acceleration profile ends and the motor continues

running until the 'Stop Steps' button is clicked. When the stepper is commanded to stop, the controller

performs the same actions as it did while accelerating, but in reverse order to decelerate until the stop

speed PPS value is reached, in which case the motor fully stops.

Figure 6 shows the acceleration profile and the role each parameter plays during speed computation.

Figure 6. Controls Available for Speed Mode

3.3.1.1.2 Step Mode

Step Mode allows the user to move the stepper motor a configured number of steps. Stepper controls are

enabled only when ‘Motor Driver' control is enabled. ‘Start Steps’ button is enabled only when ‘Driver

Outputs' control is enabled for example, AEN and BEN pins are set to high. When the ‘Start Steps’ button

is clicked, the motor starts spinning at the starting speed and accelerates at the rate configured to reach

until the number of steps is reached after which it stops.

The acceleration and deceleration profiles work similarly as before, except when the deceleration routine

starts and when the motor stops are a function of the 'Steps to Stop' and deceleration rate parameters.

The configuration can be visualized in the graph embedded in the GUI. If the "Reciprocate" button is

enabled, the stepper will travel the set number of steps, then reverse direction. It will do this continuously

until 'Stop Steps' is clicked. Figure 7 shows the controls available in Step Mode.

Figure 7. Controls Available for Step Mode

GUI Application

www.ti.com

8SLOU537–June 2020

Submit Documentation Feedback

DRV8428E EVM GUI User's Guide

The parameters from 'Speed Mode' are reused as well, and they operate the same as described in

Section 3.3.1.1.1. Two new parameters have been added to properly control the limited number of steps

actuation. These parameters are described as follows:

Number of Steps— This parameter is the number of steps that the controller will issue.

Steps to Stop— The controller is continuously monitoring the step being issued and when the current

step is equal to the 'Steps to Stop' parameter, a deceleration profile is issued. If the value of the

'Steps to Stop' parameter is larger than the number of steps, then the motor stops abruptly and

without undergoing a deceleration profile.

When a deceleration profile is issued, the controller decreases the speed until reaching the value of the

'Stopping Speed' parameter. If the 'Number of Steps' parameter is met before the deceleration profile is

complete, then the motor stops at the current speed. If the stopping speed is met before all the number of

steps is issued, then the motor rotates at the stop speed value until all the steps are executed.

Ideally, the system should resemble the case in which the controller executes all the commanded steps at

a speed as close as possible to the stop speed. In the event this is not possible because of the particular

parameters that were selected, stopping the motor at a speed very close to the 'Stopping Speed'

parameter is often good enough to ensure good motion quality and application performance.

Figure 8. Stop Conditions

3.3.2 Decay Mode and TOFF setting

Decay refers to how the driving currents recirculate in H-bridge FETs during the off time. Using the GUI,

users can configure the decay mode and TOFF for each bridge.

Figure 9. DRV8428E EVM GUI (Decay Mode and TOFF setting)

www.ti.com

GUI Application

SLOU537–June 2020

DRV8428E EVM GUI User's Guide

Decay mode and appropriate TOFF values can be configured in this pulldown menu. For more information

about the different decay modes and TOFF setting, refer to the DRV8428E Motor Driver datasheet.

3.3.3 Use the Side-Bar Menu

Use the side-bar menu in the left pane to navigate to the different pages at any time. Click on the

hamburger button in the top-left corner of the GUI to expand the side-bar menu. The following pages that

are displayed in the side-bar menu:

• Home (landing page)

• Motor control (motor control page)

• Motor driver (DRV8428EEVM GUI home page)

3.3.4 Menu Bar Options

The following menus are available in the menu bar displayed at the top of the GUI as shown in Figure 10.

Figure 10. DRV8428E EVM GUI (Menu Bar – Help Option)

3.3.4.1 File Menu

The user can load the firmware (.out) file onto the onboard MSP430 by clicking file menu and selecting an

appropriate motor driver device to match the EVM variant. For the firmware load to work, MSP430 FET

needs to be plugged into the J2 connector on the EVM board.

3.3.4.2 Options Menu

This menu provides the option to configure the serial port communication settings.

GUI Application

www.ti.com

10 SLOU537–June 2020

Submit Documentation Feedback

DRV8428E EVM GUI User's Guide

3.3.4.3 Tools Menu

The "log pane" option in this menu is to open a log pane at the bottom of the GUI which shows the GUI

actions.

3.3.4.4 Help Menu

The Help Menu contains options to view Readme File and About Section. The About Section displays the

installed software information, including the application version.

Table des matières

Autres manuels Texas Instruments Carte mère

Texas Instruments

Texas Instruments TMAG5110-5111EVM Manuel utilisateur

Texas Instruments

Texas Instruments LMX2430 Manuel utilisateur

Texas Instruments

Texas Instruments ADS1258EVM-PDK Manuel utilisateur

Texas Instruments

Texas Instruments AN-1521 POEPHYTEREV-I Manuel utilisateur

Texas Instruments

Texas Instruments AN-1975 LMP8640 Manuel utilisateur

Texas Instruments

Texas Instruments SWIFT TPS54350EVM-235 Manuel utilisateur

Texas Instruments

Texas Instruments TPS61165EVM-283 Manuel utilisateur

Texas Instruments

Texas Instruments TPS63806EVM Manuel utilisateur

Texas Instruments

Texas Instruments TPA3123D2 Manuel utilisateur

Texas Instruments

Texas Instruments INA282-286EVM Manuel utilisateur

Texas Instruments

Texas Instruments DLP LightCrafter Display 3010 Manuel utilisateur

Texas Instruments

Texas Instruments TMS320DM642 Manuel utilisateur

Texas Instruments

Texas Instruments LM5180-Q1 Manuel utilisateur

Texas Instruments

Texas Instruments bq2415x Manuel utilisateur

Texas Instruments

Texas Instruments AMC7812EVM-PDK Manuel utilisateur

Texas Instruments

Texas Instruments TRF3711xxEVM Series Manuel utilisateur

Texas Instruments

Texas Instruments DRV201 Manuel utilisateur

Texas Instruments

Texas Instruments TPS40400EVM-351 Manuel utilisateur

Texas Instruments

Texas Instruments ADS7038-Q1 Manuel utilisateur

Texas Instruments

Texas Instruments AFE5818 Manuel utilisateur

Texas Instruments

Texas Instruments DS90UB954-Q1EVM Manuel utilisateur

Texas Instruments

Texas Instruments DAC5686 EVM Manuel utilisateur

Texas Instruments

Texas Instruments LP877451Q1EVM Manuel utilisateur

Texas Instruments

Texas Instruments TUSB522PEVM Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur