TerraTrike SPYDER Manuel
www.TerraTrike.com | 616.608.8086
Revised 10/2021
Build Notes
&
www.TerraTrike.com | 616.608.8086
Frame Assembly
Install rear frame section and derailleur hanger as shown below.
Torque specs:Top bolt(2) 8.5Nm, Bottom Bolt(4) 20Nm.
1 15x23mm Cap WH000048
2 15x74mm Bolt WH000049
3 28.6x28mm Cap WH000050
4 28.6x77mm Bolt WH000051
5 Derailleur Hanger with Bolt WC000040
1
2 3
4
5
www.TerraTrike.com | 616.608.8086
Alignment
29¼
Inate tires before performing alignment. The Spyder alignment measurement is
approximately 29¼ inches (center tread to center tread), though slight variance is
possible. Most importantly, make sure the alignment remains neutral with a rider
seated in the trike.
Left
Right
Tie Rod Assembly
29¼
www.TerraTrike.com | 616.608.8086
Spyder Steering Stack Assembly
1M6x30 Socket Head Bolt TT000576
2Hybrid Top Cap TT000506
3Spyder Handlebar Pair TT600930
4Hybrid Headset Spacer TT000520
5 Hybrid Headset Cap TT000505
6Plastic Bushing TT000504
7 Hybrid Headset Bearing TT000600
8Hybrid Steering Crown Race TT000601
9 Rapid Axle Hubmount - RH TT000713
Rapid Axle Hubmount - LH TT000714
Rapid Axle Hubmount - Pair TT000516
10 Rapid Axle - RH TT000717
Rapid Axle - LH TT000718
Rapid Axle - Pair TT000563
11 Axle Spacer TT000568
9
8
7
1
6
3
6
5
4
2
10
www.TerraTrike.com | 616.608.8086
Steering Stack Assembly Continued* Install
11
Install Axle Spacer (11) between brake rotor and hub.
www.TerraTrike.com | 616.608.8086
Handlebar Assembly
Minimum insertion of the handlebars is 7cm from the alignment marking nearest the
handlebar upright.
Brake Lever Orientation: (Spyder model only)
www.TerraTrike.com | 616.608.8086
Chain Tube Setup/ Idler Setup
1
16t Aluminum Idler with cage
WC000041
2M8x30 Bolt TT000280
3
14cm LDPE Chain Tube
WC000039
4
Spyder Chain Tube Clamp
WC000038
1
16t Aluminum Idler with cage
WC000041
2M8x30 Bolt TT000280
1
2
3
1
2
4
www.TerraTrike.com | 616.608.8086
Cable Routing
Note: Internal cable routing kit is necessary to complete cable routing.
Remove Spyder Head Badge and housing ferrules prior to routing cables.
Chain Routing
Right Hand:
When routing RH cable housing, it is recommended to start installation at outrigger
cable guide. Feed housing from outrigger to the badge window, and then through
the mainframe. Next, route the housing from the mainframe through the rear frame
section to rear derailleur. Finish by routing housing from outrigger cable guide, to
handlebar cable guide and through handlebar. Install shifter and shift cable.
Shift Cable (solid=external routing, dashed=internal routing)
Brake Cable
www.TerraTrike.com | 616.608.8086
Left Hand:
When routing LH cable housing, it is recommended to start installation at boom
cable guide. Feed housing through boom/boom receiver tube to the badge window,
and then through outrigger. Finish by routing housing from outrigger cable guide to
handlebar cable guide and through handlebar. Install shifter and shift cable.
Brake Cable
Shift Cable (solid=external, dashed=internal)
www.TerraTrike.com | 616.608.8086
Inline Barrel Adjuster: (Spyder model only)
Install inline barrel adjuster on rear cable housing after the housing has been routed
through the frame. Install the 7” cable housing section between barrel adjuster and
rear derailleur.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels TerraTrike Vélo
TerraTrike
TerraTrike GTS Manuel
TerraTrike
TerraTrike EVO Manuel
TerraTrike
TerraTrike Rambler 2020 Manuel
TerraTrike
TerraTrike TANDEM PRO Manuel utilisateur
TerraTrike
TerraTrike E.V.O. with Bosch Active Line Plus Manuel utilisateur
TerraTrike
TerraTrike Rover Manuel utilisateur
TerraTrike
TerraTrike Rambler Manuel utilisateur
TerraTrike
TerraTrike Tour II Manuel utilisateur
TerraTrike
TerraTrike CHARGE Manuel
TerraTrike
TerraTrike GranTourismo Manuel
