Terex SmartPTO Manuel utilisateur

TEREX UTILITIES TECHNICAL SUPPORT TEAM

PHONE: 1-844-TEREX4U (1-844-837-3948) | EMAIL: [email protected]

MODEL(S): TOOLS NEEDED:SERVICE CALL:

NO.

EV SMARTPTO QUICKSTART

GUIDE

INTERNATIONAL EV CHASSIS NONE

EV SMARTPTO QUICKSTART GUIDE

192

DANGER

Failure to obey the instructions and safety

rules in the appropriate Operator’s Manual and

Service Manual for your machine will result in

death or serious injury.

Many of the hazards identied in the

Operator’s Manual are also safety hazards

when maintenance and repair procedures are

performed.

DO NOT PERFORM

MAINTENANCE UNLESS:

√You are trained and qualied to perform

maintenance on this machine.

√You read, understand and obey:

•manufacturer’s instructions and safety rules

•employer’s safety rules and worksite

regulations

•applicable governmental regulations

√You have the appropriate tools, lifting

equipment and a suitable workshop.

The information contained in this Tech Tip is a

supplement to the Service Manual. Consult the

appropriate Service Manual of your machine for

safety rules and hazards.

PAGE 2 OF 7

TECH TIP 192 | RELEASED 11.17.2022 | VERSION 1.0

PAGE 3 OF 7

CONTENTS

TECH TIP#192

TOC

4| Verify high voltage switches

| Turn the ignition key ON

STEP 1 - STEP 2

5| Parking brake

| E-stop

STEP 3 - STEP 4

6| Viatec system

STEP 5 - STEP 6

TECH TIP 192 | RELEASED 11.17.2022 | VERSION 1.0

STEP 2

Turn the ignition key to the ON position. The truck cannot be in the drive mode.

The cluster screen should not have a drive symbol on it. If the drive symbol is visible, cycle the

ignition to the ON position to get the chassis out of drive mode. Figure 3 shows the screen in drive

mode and Figure 4 shows the screen not in drive mode.

FIGURE 1

STEP 1

Verify that both high voltage shutoff switches are in the ON position. One is located in the cab, the

other is on the backside of the battery box. If both switches are off, turn on the cab switch rst.

FIGURE 2

FIGURE 3

PAGE 4 OF 7

TECH TIP 192 | RELEASED 11.17.2022 | VERSION 1.0

STEP 3

Verify that the parking brake is engaged (pulled

out), and the truck is in neutral.

FIGURE 4

STEP 4

Verify that the e-stop is pulled out on the

Viatec system. The e-stop Is located on a

square weldment behind the last curbside

compartment.

PAGE 5 OF 7

TECH TIP 192 | RELEASED 11.17.2022 | VERSION 1.0

STEP 5

Verify that the Viatec symbol on the bottom left

of the screen displays detected. If the system

is detected, press the PTO button.

FIGURE 8 FIGURE 9

FIGURE 7

STEP 6

Verify that under the viatec symbol the wording

changed from Detected to Allowed. This lets the

operator know that all the interlocks have been

met to allow the system to run. Figure 8

Then press the E-PTO buttom. It will turn

yellow during start-up and then will turn green.

Once the motor can be heard turning, the smart

PTO system is ready to use.

Figure 9

If any faults are detected, consult the

manufacturer’s manual for troubleshooting. If

you have any questions call 1-844-TEREX4U

(1-844-837-3948) or email utilities.service@

terex.com

PAGE 6 OF 7

FOR FURTHER ASSISTANCE,

CONTACT THE TEREX UTILITIES TECHNICAL SUPPORT TEAM

PHONE: 1-844-TEREX4U (1-844-837-3948) | EMAIL: [email protected]

Table des matières

Autres manuels Terex Système de levage

Terex

Terex Genie GS-2669DC Manuel utilisateur

Terex

Terex Genie SX-105 XC Manuel utilisateur

Terex

Terex GS90D-4695 Manuel d'installation et d'exploitation

Terex

Terex Genie GS-1530 Manuel utilisateur

Terex

Terex Genie Z-60/37DC Manuel utilisateur

Terex

Terex SX135D-101 Manuel utilisateur

Terex

Terex Genie Load Lifter Manuel utilisateur

Terex

Terex Genie S-80 XC Series Manuel utilisateur

Terex

Terex Genie AWP Series Manuel utilisateur

Terex

Terex Genie GR Series Manuel utilisateur

Terex

Terex Genie SX-150 Manuel d'installation et d'exploitation

Terex

Terex Genie TX-34/20 Manuel utilisateur

Terex

Terex Genie Z-45/25 Bi-Energy Manuel utilisateur

Terex

Terex Robot 5000 Manuel de service

Terex

Terex Genie Lift Guard S-60 Manuel utilisateur

Terex

Terex Genie SHOV5DL15B-1001 Manuel utilisateur

Terex

Terex Genie GTH4016 SR Manuel utilisateur

Terex

Terex Genie GS84D-401 Manuel d'installation et d'exploitation

Terex

Terex Genie Super Series Manuel utilisateur

Terex

Terex Genie GS-1432m Manuel d'installation et d'exploitation

Terex

Terex GTH08E-11500 Manuel d'installation et d'exploitation

Terex

Terex S-60 J Manuel utilisateur

Terex

Terex SX18014-101 Manuel utilisateur

Terex

Terex Genie GRC-12 Manuel utilisateur

Manuels Système de levage populaires d'autres marques

morse

morse 82H-124 Manuel utilisateur

Braun

Braun NL955 Series Manuel utilisateur

haacon

haacon 1889.10 Manuel utilisateur

Protekt

Protekt AT 252 Manuel utilisateur

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuel utilisateur

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuel utilisateur

Genie

Genie Z-60/34 Manuel utilisateur

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuel utilisateur

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuel de programmation

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuel de programmation

BERG

BERG BeNomic EasyLeaf Manuel utilisateur

Powermate

Powermate LiftGate LG-3 Manuel utilisateur

Snorkel

Snorkel TM12 Series Manuel utilisateur

Terberg

Terberg OMNIDEKA Manuel utilisateur

Harmar Mobility

Harmar Mobility AL625 Mode d'emploi

Rotary

Rotary SPO16 Manuel utilisateur