Tennant 6080 Manuel de formation

IB340068 (9-99)LITHOIN U.S.A.1

No.340068

Machine:6080/3640

Published:9-99/01

INSTRUCTION BULLETINSystem:SWEEPING

NOTE:DONOTDISCARD thePartsList fromtheInstruction Bulletin.Place theParts

Listinthe appropriateplace inyourmachinemanualforfuturereference.

Retaining thePartsListwill make iteasiertoreorderindividualparts and will

save you the costofordering anentire kit.

NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.

Installation Instructions for Kit number 80302

SYNOPSIS/PROBLEM:

This kit contains the parts needed to install a new side brush lift cable on the model 6080

and 3640 sweepers. Please follow step-by-step instructions.

SPECIAL TOOLS/CONSIDERATIONS:None

(Estimated time to complete: 2 hour)

INSTALLATION:

(Referto FIG.1,2 and 3)

FORSAFETY:Beforeleaving orservicing machine,stop on levelsurface and setparking

brake.Thenturn off machine and remove key.

1. Remove the filter cover from the rear of the machine. Remove the handle stop bracket

from the upper/left side of the filter compartment. (RefertoFIG.1)

2. Pull up on the two handle locks and move the handle assembly to its lowest position.

(RefertoFIG.3)

(1)

FIG.1-- CoverPlateAnd Handle

3. Remove the three hex screws holding the cover plate to the inside of the right side handle

tower. Remove the cover plate from the machine. (RefertoFIG.1)

4. Remove the bolt holding the pivot plate to the plastic side arm. This will allow the plate and

handle assembly to be pulled away from the plastic arm for easy access. (RefertoFIG.1)

IB340068 (9-99)LITHOIN U.S.A.2

5. Remove the cotter pin and clevis pin from the end of the side brush lift cable where it

attaches to the side brush lift lever. (RefertoFIG.1)

6. Remove the nut from the clamp holding the side brush cable to the mount plate.

(RefertoFIG.1)

7. Remove the debris hopper from the machine.

8. Locate the side brush lower mount bracket on the right side of the frame, near the right

front caster. (RefertoFIG.2)

9. Remove the two hex screws holding the side brush lower mount bracket to the machine

frame. (RefertoFIG.2)

FIG.2-- SideBrushBracketAnd Cable

10.Pull the mount bracket out of the hole in the frame. Pull the side brush cable out of mount

slot. (RefertoFIG.2)

11.Remove the two hex screws holding the side brush lift cable spring assembly to the right side

of the machine frame, out near the right side brush. (RefertoFIG.2)

12.Pull the spring and cable assembly out of the machine frame. (RefertoFIG.3)

13.Remove the clevis pin holding the side brush lift cable to the spring assembly. Remove the

side brush lift cable from the spring assembly. (RefertoFIG.3)

14.Route the new lift cable (1) down the handle assembly, thru the hole in the handle, into the

hole in the main frame, and down to the right side of the frame. Next, reach in the frame

hole and grab the cable.

NOTE: Add the cable tie (2) around the new side brush cable (1) and the existing stiff

main brush lift cable. This will prevent the new side brush lift cable from drooping down

and rubbing on the brush drive pulley.

15.Reconnect the cable to the side brush spring assembly. Reinstall the spring assembly on the

frame. Tighten the two hex screws to 7.6 -- 9.9 Nm (6 -- 8 ft lb). (RefertoFIG.3)

16.Position the side brush lift cable in the slot on the lower mount bracket. Reinstall the lower

mount bracket in the machine. Tighten the two hex screws to 8 -- 24Nm (15 -- 20 ft lb).

(RefertoFIG.2)

IB340068 (9-99)LITHOIN U.S.A.3

17.Go up to the main brush lift lever and install the nut on the main brush lift cable mount clamp.

Tighten the nut to 7.6 -- 9.9 Nm (6 -- 8 ft lb). (RefertoFIG.1)

18.Install the clevis pin and cotter pin in the end of the new cable where it attaches to the main

brush lift lever. (RefertoFIG.1)

19.Reinstall the right side handle assembly cover plate. Tighten the three hex screws to

18 -- 24 Nm (15 -- 20 ft lb). (RefertoFIG.1)

(1)

FIG.3-- CableAssemblyAnd Stop Bracket

20.Move the handle assembly up to one of the four adjustment holes.

21.Reinstall the filter cover and the handle stop bracket. (RefertoFIG.3)

22.Reinstall the hopper.

23.Start the machine and check the side brush lift cable for proper operation.

24.Close the machine cover.

BILL OFMATERIALSFORSIDEBRUSH CABLEKIT80302

TENNANT

Ref.PartNo.Description Qty.

1 80191 Side brush cable 1

2 49266 Cable tie 1

TENNANT COMPANY

P. O. Box 1452

Minneapolis, MN 55440-1452

Autres manuels pour 6080

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Tennant Machine de plancher

Tennant

Tennant sentinel Manuel utilisateur

Tennant

Tennant R3 ReadySpace Manuel utilisateur

Tennant

Tennant T3 Manuel utilisateur

Tennant

Tennant 5200 Manuel du produit

Tennant

Tennant 6400E Manuel utilisateur

Tennant

Tennant 1100 Manuel du produit

Tennant

Tennant 1510 Manuel du produit

Tennant

Tennant B5 Manuel utilisateur

Tennant

Tennant 2510 Manuel utilisateur

Tennant

Tennant i-team i-mop xxl Manuel utilisateur

Tennant

Tennant 6100 Manuel utilisateur

Tennant

Tennant 1200 611468-230V Manuel utilisateur

Tennant

Tennant SweepSmart S20 ELECTRIC Manuel de formation

Tennant

Tennant T20 LPG Manuel utilisateur

Tennant

Tennant T981 Manuel utilisateur

Tennant

Tennant 5500 Complete Manuel du produit

Tennant

Tennant 340513 Manuel de formation

Tennant

Tennant 5700 Manuel utilisateur

Tennant

Tennant 810 Gas Manuel utilisateur

Tennant

Tennant F14 Manuel du produit

Tennant

Tennant E5 Manuel utilisateur

Tennant

Tennant T20 LPG Manuel utilisateur

Tennant

Tennant BOSS 2000E Manuel du produit

Tennant

Tennant SM15040 Manuel du produit

Manuels Machine de plancher populaires d'autres marques

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Manuel utilisateur

Numatic

Numatic ET 4045 Manuel utilisateur

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Manuel utilisateur

Mytee

Mytee 8070 Mytee-Lite Manuel utilisateur

Kärcher

Kärcher B 140 R Manuel utilisateur

Triple S

Triple S Ace 26T1 Manuel utilisateur

Nilfisk-Advance

Nilfisk-Advance SW 750 Manuel utilisateur

Tornado

Tornado Marathon 2000 98190 Manuel

Windsor

Windsor ADMIRAL Admiral 8 Manuel utilisateur

Numatic

Numatic TTB 1117/100 Manuel utilisateur

Nobles

Nobles Frontier Manuel du produit

lavina

lavina 21-X Manuel utilisateur

KENT

KENT Edge 28B Manuel utilisateur

Windsor

Windsor BDP 51/2000C Manuel utilisateur

CleanFreak

CleanFreak DURA-18HD Manuel utilisateur

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Guide de l'administrateur

BETCO

BETCO PB24 Manuel utilisateur

IPC

IPC CT51-71 BT Manuel utilisateur