Teltone ILS-B Manuel utilisateur

ISDN Demonstrator

ILS-B

User’s Manual

40-400-00011, Rev. B

Note

This manual covers Model ILS-B-01.

Trademarks

Teltone is a registered trademark of Teltone Corporation.

Windows is a registered trademark of Microsoft Corporation.

Other company and product names may be trademarks or

registered trademarks of their respective owners.

Teltone Corporation

Bothell, Washington 98021 USA

Customer Service: 425-951-3388

Technical Support: 425-951-3390

Fax: 425-487-2288

Email: [email protected]

Website: www.teltone.com

40-400-00011, Rev. B iii

Table of Contents

Introduction..........................................................................................................1

Unpacking............................................................................................................1

Chapter 1: Quick Start ......................................................................................2

ISDN Demonstrator Operation ................................................................5

What To Read Next .................................................................................6

Chapter 2: ISDN-BRI .......................................................................................7

Technology Overview..............................................................................7

Layer 1 - Physical Operation ...................................................................7

U Reference Point.............................................................................7

Network Termination-1 (NT-1)........................................................8

S/T Reference Point..........................................................................8

Terminal Adapters ............................................................................8

Layer 2 - Data Link Operation.................................................................8

Packet Addressing ............................................................................8

TEI Assignment ................................................................................9

Layer 3 - Network Operation...................................................................9

Service Profile ID (SPID) Assignment.............................................10

Chapter 3: Provisioning and Operation.............................................................11

Configuration Software Installation.........................................................11

General Operation....................................................................................13

Defaults....................................................................................................13

Switch Type .............................................................................................13

D Channel X.25 .......................................................................................14

Packet Handling Function (PHF)......................................................14

B Channel Provisioning ...........................................................................15

Caller ID...................................................................................................15

Terminal Display Text .............................................................................16

Electronic Key Telephone Service (EKTS).............................................17

Multi-Point...............................................................................................18

Call Appearances .....................................................................................18

Key Hold..................................................................................................19

Additional Call Offering (ACO)..............................................................20

Chapter 4: Demonstrator Operation..................................................................21

Restart ......................................................................................................22

Chapter 5: Reference.........................................................................................23

Status Indications.....................................................................................23

Dimensions and Panels ............................................................................24

Supported Call Control Messages............................................................24

Typical Call Control Sequence ................................................................26

Troubleshooting .......................................................................................27

Physical Interface..............................................................................27

TEI Assignment ................................................................................28

Call Control ......................................................................................28

Configuration....................................................................................30

40-400-00011, Rev. B

Reference Documents ..............................................................................30

Warranty and Service...........................................................................................32

Warranty Information ..............................................................................32

Return Procedures....................................................................................32

Technical Assistance................................................................................32

Maintenance.............................................................................................32

Cleaning............................................................................................32

Servicing ...........................................................................................32

Specifications.......................................................................................................33

Glossary ...............................................................................................................34

40-400-00011, Rev. B v

List of Figures

Figure 1. Configuration Software ........................................................................12

Figure 2. U Interface Operation...........................................................................23

Figure 3. Dimensions and Panels.........................................................................24

Figure 4. Call Control Message Exchange Example ...........................................26

40-400-00011, Rev. B

IMPORTANT SAFETY INSTRUCTIONS

When using this product, basic safety precautions, including the following, should always be followed to reduce the risk of

fire, electric shock, and injury to persons.

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. The product should be operated only from the type of power source indicated on the marking label. If you are not sure

of the type of power supply, consult your dealer or local power company. The product is designed for indoor use only.

4. To reduce the risk of electric shock, do not disassemble the product, but take it to qualified service personnel when

service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks.

Incorrect reassembly can cause electric shock when the appliance is subsequently used.

5. If the product does not operate normally by following the operating instructions, or if the product has been dropped or

the cabinet has been damaged, or if the product exhibits a distinct change in performance, refer servicing to qualified

service personnel.

6. If the product is used in a manner other than specified in this manual, the protection provided by the product may be

impaired.

7. For the purpose of removing power from the product, the power input connector is the main power disconnect point.

Pull the power cord away from the connector to ensure power disconnect.

8. Adequate air flow must be maintained in order for the product to operate correctly. Do not wrap the product in

blankets, paper, or other material that may impede ventilation.

40-400-00011, Rev. B vii

REGULATORY COMPLIANCE

FCC Part 15 Class A Notice: This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

40-400-00011, Rev. B 1

ISDN Demonstrator

INTRODUCTION

ISDN (Integrated Systems Digital Network) is a system which combines

telephone and computer networking in a digital medium. The ISDN BRI

(Basic Rate Interface) is the interface for individual users to connect to the

public telephone network. An ISDN BRI is composed of three separate

channels of information called 2B+D, that is, two full duplex Bearer channels

and one full duplex Delta channel combined onto a single pair of wire.

The Teltone ISDN Demonstrator is two ISDN BRI connections in a portable

housing. The user interface is “U” connection using an RJ45 modular plug.

The “U” connection is similar to the interface that is provided by a local

telephone service provider (LEC), such as one of the Bell Operating

Companies, or an independent telephone company. Using this connection,

the user is able to place calls, either voice or data, or both, using the National

ISDN-1 signaling standard. AT&T 5ESS Custom provisioning is available as

a separate option (ILSATT-01).

ISDN is based upon an OSI (Open System Interconnection) model. The

ISDN Demonstrator supports layer 1 (physical operation), layer 2 (data link

operation), and Layer 3 (network operation.) Layers 4-7 are considered

application layers that use the first 3 layers as a base.

The ISDN Demonstrator has been developed to make demonstrating of

ISDN CPE equipment easier. Integrators, and sales representatives now

have an ISDN-BRI server in a box. The ISDN Demonstrator supports ISDN-

BRI end-to-end operation, multiple Call Control protocols, telephony switch

services, and simple functional operation on the desktop or lab bench.

UNPACKING

Carefully unpack the items in the shipping container and verify that you have

received the following:

1. ILS-B-01, ISDN Demonstrator Unit

2. 115 VAC Power Cord

3. This User Manual

4. System Configuration Diskette

5. Product Registration Card

6. DB9F-DB25M 6-ft RS-232 cable (p/n 742-00022-01)

7. DB9M-DB25F adapter (p/n 742-00020-01)

Optional Accessories:

1. AT&T custom configuration software (diskette) (p/n ILSATT-01)

ISDN Demonstrator User’s Manual

40-400-00011, Rev. B

CHAPTER 1: QUICK START

The ISDN Demonstrator is easier to operate than most communications

devices designed for ISDN-BRI applications. It functions in the background,

providing two lines of end-to-end ISDN-BRI service.

Because the Simulator was designed primarily for people who demonstrate,

functionally test, or configure ISDN-BRI devices, you do not need to

understand ISDN protocols or read the entire User’s Manual to use it. Simply

follow the instructions outlined below to successfully demonstrate most

ISDN-BRI communications devices and computer applications.

Step 1 Place the Simulator on a flat surface near the ISDN equipment

to be connected.

Step 2 Insert the power cord into the three-pronged outlet located at

the rear of the Simulator. Plug the other end into a standard

115 VAC, 60 Hz wall outlet.

Step 3 Apply power to the Simulator by pressing the power switch -

located at the rear of the Simulator - to the PWR ON position.

An internal self-test, lasting about 30 seconds, is performed.

The STATUS LED located on the front panel will switch

between Red and Green during this self-test. The STATUS

LED changes to a continuous solid green if the self-test is

completed satisfactorily.

Step 4 The Simulator is configured at the factory for National ISDN-1

protocol. The Simulator is provisioned for default service, as

normally practiced for the selected switch type. Most

communications devices operate correctly with this

provisioning. However, if your communications device does

not operate correctly, you may need to change the Simulator’s

provisioning. These settings are fully described in Chapter 3. A

list of recommended settings for different terminal types (AT&T

CUSTOM) is available in the ISDN Demonstrator configuration

software.

NOTE: The instructions for many ISDN-BRI

communications devices may specify Switch Provisioning

required of the telephone company. Provisioning is a

means of configuring the ISDN switch so it knows what

kind and how many calls your communications devices

can handle, up to the limits imposed by ISDN-BRI

technology. Provisioning also specifies which types of

Supplementary Services your equipment may request,

such as call appearances, display support, etc.

Step 5 A 3.5" diskette is provided with the ISDN Demonstrator to

change the configuration of the ISDN Demonstrator. To install

this windows based software, place the diskette in the

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Teltone Matériel réseau

Teltone

Teltone TSP Edge Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur