Telguard TG-4 Manuel utilisateur

24 HOUR ZONE (N.C.)

TELCO DIALER

123 5 6 1 2

SIM

Power LED

EARTH

GROUND

LED Mode

Toggle Button

LEDs 2-5

Signal (dBm) NO

SVC < -110 > -110 > -100 > -90 > -80 > -70 > -60

RSSI (bars) NONE 1½1 2 2½ 3 3½

System Status LEDs (RSSI Mode)

OFF

BLINKING

System Status

LEDs

Alarm Panel

Battery

Connector

Acceptable RSSI Range

BATTERY

Battery wire

should be at

least ¼ inch

apart from

AC wires

Not Used

1 2 1 32

1 2 1 2 3 4 5 6 1 21 2 3

OPTIONAL

BATTERY

STC2

(N.C) STC1

(N.O.) GND IN

TRIP

345

GREEN

RED

INCOMING

TELCO

RJ31X

24 HOUR ZONE (N.O.)

TELGUARD

Digital TG-4

GND DC

1 FLASH = ACFC LOW/MISSING AC

LPF LOW DC INPUT

2 FLASH = LBC LOW BATTERY

3 FLASH = LFC LINE FAULT

4 FLASH = NSC NO SERVICE

5 FLASH = RFC RADIO FAILURE

6 FLASH = DTF DIAL TONE FAIL

7 FLASH = PPF PNL PRES FAIL

LED 1

OFF NOT ACTIVATED

ACTIVATEDON

System Status LEDs (Normal Mode)

ACTIVATION DENIED (DISABLED)FLASHING

ACTIVATION

LED 2

OFF

FLASHING

SYSTEM

TROUBLE

NO TROUBLE

TROUBLE:

LED 3

OFF

PANEL COMM PANEL ON-HOOK (PRIMARY)

PANEL ON-HOOK (BACKUP)

LED 4

OFF IDLE

WAITING FOR RESPONSE FROM

TCC

ACTIVATION DENIEDFLASHING

TMC COMM

LED 5

OFF IDLE

RADIO INITIALIZINGON

RADIO COMMUNICATINGFLASHING

RADIO STATUS

PANEL OFF-HOOKFLASHING

LED 6

LED 7LED 8

OFF NOT USED

NOT USED

AC NOT CONNECTED

UNIT MAY BE RECEIVING

POWER FROM DC/BATTERY

OFF

POWER LED

FLASHING STANDARD LINE SECURITY ENABLED

(2 FLASHES EVERY 5 SECONDS)

(12V 800MA) AC CONNECTED TO UNITON

Telguard Model TG-4

QUICK INSTALLATION GUIDE

Installation Summary

There areseven steps in installing Telguard properly. IF YOU DO NOT

PROCEED IN THE ORDER ANDMANNER PRESCRIBED, YOU MAY

NOT COMPLETE THE INSTALLATION IN THE TIME ALLOCATED.

STEP 1: REGISTER FOR CELLULAR SERVICE

completing the Online Registration Format www.Telguard.com. Telular

requires this information to activate the unit.

STEP 2: LOCATE UNIT AND MEASURE SIGNAL STRENGTH (RSSI)

First,you willbe confirming that Telguard has adequate cellular signal strength. Press the LED

Mode Toggle button, LEDs will now indicate signal strength. Minimum recommended is 2 ½

(2 on solid and the third flashing). ). The LED Mode will reset to normal automatically after 10

minutes or after pressing the LED Mode Toggle button again.

STEP 3:TRANSMIT PANEL ALARMS OVER THE TELCO CONNECTION

Next, you willverify that the alarm panel is programmed properly. Thisstepis important to

verify that the alarm panel is programmed withvalid account code and central station

information before transmitting signals through the cellular network.

STEP 4: PROGRAM,ACTIVATE &TRANSMIT PANEL ALARMS OVER

THE CELLULAR RADIO NETWORK

Next, you will be connecting the alarm panel's digital dialer output to Telguard and verifying that

alarm signals can be reliably sent through Telguard over cellular to the central station digital

receiver. The incoming Telco line is not connected to Telguard during this step.A minimum of

two alarm signals must be transmitted. Activation is confirmed when LED 1 is illuminated.

(NOTE:THE FIRST ALARM WILL ACTIVATE THE UNIT AT THE TELULAR COMMUNICATION

CENTER,IT WILL NOT GO TO THE CENTRAL STATION,ALL SIGNALS AFTER THE FIRST ARE

SENT TO THE CENTRAL STATION)

STEP 5: CONNECT SUPERVISORY TRIP OUTPUTS

Next, you will wire Telguard's supervisory tripoutputs to the alarm panel and then test.

STEP 6: CONNECT TRIP INPUT (OPTIONAL)

Optionally, you can wire an external relay input to the trip input lead and ground, and test.

STEP 7: COMPLETE THE INSTALLATION

Your last step will be to attach earth ground, and permanently mount the unit.

56044002

Setup & Programming the Operating Parameters in the Telguard TG-4

When the Telguard is received from the factory and is powered up for the first time, it is immediately ready for activation, provided the default settings

are what you want (note: registration form must be sent to Telular). The STC LED # 2 will flash to indicate any failure conditions. The Mode LED # 3

will be on and the STC 1 and STC 2 relays will be tripped. If changes are required to the default settings, the Telguard can be programmed using a

line-mans butt-set connected to T & R Test Points or a POTS phone connected to the panel RJ-45 jack (black connector where the alarm panel is

normally connected).

TO PROGRAM THE Telguard TG-4

A. Put the line-mans butt-set in talk mode or pick up the POTS phone.

B. Connect power to the Telguard, when ready for programming you will hear 2 beeps.

C. Press #, *, this will put the Telguard into a Master Access programming mode, 2 beeps.

D. Enter changes required. The syntax for programming a specific memory location is as follows:

MEMORY LOCATION (3-digits), will respond with 2 beeps, then VALUE, will respond with 2 beeps.

E. Then press *, you will hear 2 beeps then hang up. This saves the change and exits the programming mode.

Mem Loc.

Field

Default Value

Setting

831

Mode of operation

1 = Telco Primary/Cellular Backup

2 = Cellular Primary/Telco Backup

3 = Cell Only

833

C/C Reporting Format

01 = 4x2 pulse, 40pps 2300 hz 02 = 4x2 pulse, 20pps 2300 hz

03 = 4x2 pulse, 10pps 1400 hz 04 = 3x1 pulse, 40pps, 2300 hz

05 = 3x1 pulse, 20pps, 2300 hz 06 = 3x1 pulse, 10pps, 1400 hz

07 = Radionics IIe or IIIa2 08 = Contact ID

09 = Auto Format Detect 11 = SIA2 (300 Baud)

12 = DMP

850

STC1 Trip Output

Reporting

Normally Open

(LFC only)

Enter the SUM TOTAL of the events that you wish to trip the STC relay by

ADDING the corresponding values:

00 = Not Used 04 = LFC 32 = DTF

01 = AC Failure 08 = NSC 63 = ALL

02 = Low Battery 16 = RFC

851

STC2 Trip Output

Reporting

Normally Closed

(all except LFC)

Enter the SUM TOTAL of the events that you wish to trip the STC relay by

ADDING the corresponding values:

00 = Not Used 04 = LFC 32 = DTF

01 = AC Failure 08 = NSC 63 = ALL

02 = Low Battery 16 = RFC

852

STC Trip Delay for NSC

2 (60 sec)

1=30 seconds 4=10 minutes 7=45 minutes

2=60 seconds 5=20 minutes 8=60 minutes

3=3 minutes 6=30 minutes 9=24 hours

858

STC History

N/A

0 = terminate STC history display mode

1 = start STC history display mode

2 = clear STC history

861

CFC Number of Events

0 (disabled)

0 = disabled 2 = 4 attempts

1 = 2 attempts 3 = 8 attempts

862

CFC Between Events

1 (30 sec)

1 = 30 seconds 3 = 70 seconds 5 = 90 seconds

2 = 60 seconds 4 = 80 seconds 6 = 99 seconds

868

PPF Delay

0 (disabled)

0 = disabled, 1 = 10 seconds, 2=20 seconds, … 15=150 seconds

872

AC Failure Delay

02 (2 hours)

0-24 hours

873

Trip Input Reporting

0 (no report)

0 = no report 1 = report trip

874

Trip Input Restoral Reporting

0 (no report)

0 = no report 1 = report restoral

875

Trip Input Swinger Function

0 (disabled)

0 = swinger function disabled

1 = swinger function enabled

899

Factory Default Unit

NOTE: SPECIAL LED INDICATIONS DURING ACTIVATION

If the Telguard fails to confirm activation it will be displayed on the LEDS:

System Status LEDs

Activation Indications

ALL LEDS FLASHING

FAILED ACTIVATION –SIGNAL TOO WEAK

LED #1 & LED #4 FLASHING

ACTIVATION ERROR –CALL TECH SUPPORT

LED #1 ON

ACTIVATION SUCCESSFUL

LED #2 OFF

NOT ACTIVATED. NEED TO CONNECT PANEL AND TRIP ZONE

On either a FAILED ACTIVATION or ACTIVATION ERROR, the unit MUST BE RESET BY PRESSING THE RSSI

BUTTON TWICE. The activation message MUST BE RESENT or the TELGUARD will transmit all signals through

the telco connection.

Autres manuels pour TG-4

Autres manuels Telguard Téléphone portable

Telguard

Telguard TG-7 Series Guide de dépannage

Telguard

Telguard TG-7 Series Manuel utilisateur

Telguard

Telguard TG-4 Manuel utilisateur