Telex Communications 2473AA Manuel utilisateur

Model 2473AA

Long Range, High Power

Wireless CPE/Outdoor Bridge

Instruction Manual

Telex Communications, Inc.

8601 East Cornhusker Hwy, Lincoln, NE 68505

Revision D, September 2003

Windows, and the Windows logo are registered trademarks of Microsoft

Corporation. All other trademarks and brand names are the property of their

respective proprietors.

LIMITED WARRANTY

TELEX Communications, Inc. ("Telex") warrants to the user who originally

purchased the product, that the product will be free from defects in material and

workmanship for the following periods after such date of purchase: Material 12

months, workmanship 12 months. Telex will at its option repair or replace free of

charge such defective products subject to the following conditions:

1. Delivery of the product or parts prepaid directly to Telex Communications,

Inc. at the following address:

Service Department

Telex Communications, Inc.

8601 East Cornhusker Highway

Lincoln, NE 68505

2. Determination by Telex that a defect exists and is covered by the limited

warranty. Defects due to alterations, repair by an unauthorized person, insertion of

non-Telex parts, misuse, accidental damage, use of the equipment for purposes

other than those for which it was designed and the like, are not covered by this

limited warranty and repairs thereof will be subject to normal service charges.

3. Repairs and replacement parts are covered under this limited warranty only for

the unexpired term of the original limited warranty.

4. Equipment returned to the factory for warranty repair must be accompanied

by a proof of date of purchase and a statement of the reported malfunction.

Questions regarding warranty service information or repair status should be

addressed to:

Service Department

Telex Communications, Inc.

8601 East Cornhusker Highway

Lincoln, NE 68505

Telephone: (402) 467-5321

VALID IN UNITED STATES AND CANADA ONLY

THIS LIMITED WARRANTY IS EXPRESSLY IN LIEU OF ANY EXPRESS

OR IMPLIED WARRANTY, INCLUDING ANY IMPLIED WARRANTY OR

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

WHICH EXTENDS BEYOND THE TERM HEREOF. THE REMEDIES

PROVIDED BY THIS LIMITED WARRANTY ARE THE ONLY REMEDIES

AVAILABLE TO ANY PERSON. NO PERSON HAS ANY AUTHORITY TO

BIND TELEX TO ANY REPRESENTATION OR WARRANTY OTHER

THAN THOSE PROVIDED BY THIS LIMITED WARRANTY. TELEX

SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES CAUSED BY FAILURE OR OTHERWISE OF THE PRODUCT.

Some states do not allow exclusions or limitations of incidental or consequential

damages or limitations on how long an implied warranty lasts, so the limitations

or exclusions herein may not apply to you. This warranty gives you specific legal

rights, and you may also have other rights, which vary from state to state.

FCC STATEMENT

This Wireless CPE has been tested and complies with the specifications for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used according to the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

is found by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment or devices

• Connect the equipment to an outlet other than the receiver’s

• Consult a dealer or an experienced radio/TV technician for assistance

Changes or modifications not expressly approved by the manufacturer could

void the user’s authority to operate the equipment!

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with

minimum distance 40cm (15.75 inches) between the radiator and your body.

Installation Requirements

The antenna used for this transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter. The operator of this

transmitter, or if the equipment is professionally installed, the installer, is

responsible for ensuring that the system is used exclusively for fixed, point-to-

point operations.

Table of Contents

Warranty & Copyright Information 2

FCC Statement 3

Chapter 1: Introduction 6

The Telex Wireless CPE/Outdoor Bridge 6

Features 7

Package Contents 8

Chapter 2: Getting to Know the Wireless CPE 9

Inside the Wireless CPE 9

The Power-Over-Ethernet Injector 10

TheRearPanelLED’s 11

Chapter 3: Installing the Wireless CPE 12

Selecting a Mounting Location 12

Attaching the Mounting Bracket and Aiming 13

Routing the CAT5 cable 14

Connecting the Wireless CPE 14

Chapter 4: Configuring the Wireless CPE 16

Change your computer network settings 17

Change the CPE wireless settings 17

SystemStatus 18

Configuration 20

Administration 22

Tools 23

Help 24

Reset your computer network settings 25

Chapter 5: Managing the Wireless CPE 26

Chapter 6: Troubleshooting 27

Chapter 7: Firmware Documentation 28

Chapter 8: Specifications 30

Chapter 1: Introduction

The Telex Wireless CPE/Outdoor Bridge

Perfect for the home or small office connection to the network, the Telex Wireless CPE

(Customer Premise Equipment) extends wireless connectivity from an access point to any

Ethernet-ready network device, such as a switch, router, desktop or notebook PC. The Wireless

CPE simply and efficiently transmits data between 10Base-T and your wireless LAN or wireless

ISP access point.

The Telex Wireless CPE gives you the freedom to place any standard networked computer

anywhere within range of an access point. A built-in 18 dBi antenna and 200 mW radio means

that you can easily cover distances of up to 12 miles.

Based on signal strength, it dynamically shifts between 11, 5.5, 2 and 1 Mbps network speeds for

maximum reliability of connection. So you’ve got the flexibility and performance you need

from your wireless LAN or wireless ISP.

Wireless data or VoIP is transmitted and received from the CPE to the network access point (AP)

on the 2.4 GHz ISM band. The radio signal path must be line-of-sight (LOS) between the 2

antennas.

Features

• An All-in-One Wireless Solution for any Ethernet-Ready Network Device

• Easy IE and Netscape Web browser configuration, no additional drivers needed

• Interoperable with 802.11b (DSSS) 2.4 GHz Equipment, Prism 2.5 based

• Up to 11 Mbps High-Speed Data Rate, Throughput up to 5.5 Mbps

• High-Power (+41 dBm EIRP) and High Sensitivity (-95 dBm @ 1 Mbps)

• 12VDC Power-over-Ethernet (PoE) supplied, up to 24VDC available

• Transient Suppression for high reliability

• Broad operating temperature, -20 to +125 F

• All nearby 802.11b access point information displayed in Wireless Scan

• Clickable association with access point within Wireless Scan

• Manual entry of ad-hoc or infrastructure mode, SSID, channel, transmission rate and

access point density available

• Selectable static IP address or DHCP client mode

• Selectable MAC address cloning

• Selectable inbound and outbound bandwidth limiting from 64 Kbps to 1500 Kbps

• Signal and noise displayed in dBm, quality displayed in %

• Tx Rate, Link quality, signal strength and noise displayed in large font in new window

for antenna aiming

• Adjustable RTS and fragmentation settings

• Up to 128 bit WEP with keys auto-generated from pass phrase

• Ability to deny unencrypted data when WEP is enabled

• Shared key authentication available when WEP is enabled

• Layer 2.5 bridging

• Changeable settings for port interface access to web server

• Support for firmware upgrades, for both interface and radio card

• Syslog client option for events logging

• Integrated 18 dBi antenna with 18 degree beam widths in both planes

• Standard multimount for DSS, mast & under eaves (fascia) mounting

• Selectable vertical or horizontal antenna polarization

• Waterproof cable entry

• Waterproof and dustproof radome enclosure

• Removable, serviceable radio area within CPE

• LED status lights visible through window on back panel

Package Contents

PoE Injector 12V Power Supply 7’ Cat5 Cable

Telex CPE Angle Bracket Hardware pack

CD & Quick Guide

Tools and Hardware Needed:

The following tools will be needed to assemble and mount your wireless CPE:

7/16” nut driver or wrench

5/16” nut driver or wrench

3/4” wrench or adjustable wrench for grommet nut

UV-stable plastic cable ties or black electricians tape

Mast pipe or DSS dish mount on which to mount the CPE

Adequate length of exterior CAT-5 cable

RJ45 plugs and crimping tool

Chapter 2: Getting to Know the Wireless CPE

Inside the Wireless CPE

Before you can either test or install the Telex Wireless CPE, you must attach a length of outdoor-

rated (external) CAT-5 Ethernet cable to the unit. Remove the access panel from the rear panel

of the CPE using a 5/16” nut driver or wrench. Loosen the plastic nut on the outside of the

waterproof cable entry grommet, then insert the unterminated end of a length of exterior CAT-5

8-conductor Ethernet cable through this grommet.

Attach a standard RJ45 connector to the end of this cable using standard wiring for a straight

(non-crossover) connection. Plug this connector into the RJ45 socket on the PCB (printed circuit

board) that is attached to the access panel. Tighten down the cable strain relief clamp on the

cable. Do NOT unplug the small antenna cable from the radio card unless absolutely necessary.

WARNING: Before touching the PCB, make sure that you are grounded and have dissipated

any static charge to ground.

Antenna

Cable

connection

Cable

strain relief

clamp

You will see a small 2-position slide switch near the RJ45 socket. If you are connecting the

wireless CPE directly to a computer network card or other Ethernet device, then slide this switch

toward the RJ45 socket. If you are connecting the wireless CPE to a hub or switch, then slide

this switch away from the RJ45 socket. Later, when you apply power to the unit, the second

green LED will indicate if this switch position was properly selected.

There are two small pushbutton switches on the PCB. These are only used if you wish to reset

the wireless CPE to factory default settings. (e.g. you forgot or lost the user name and/or

password)

Allow approximately 6 inches of CAT-5 cable between the grommet and the PCB, then tighten

the outside nut of the weatherproof grommet. Also ensure that the inside nut is secure. Make

sure that both the small antenna cable and the CAT-5 cable are secure, then re-attach the access

panel to the CPE rear panel before proceeding.

The Power-over-Ethernet (PoE) injector

The Telex Wireless CPE uses a PoE injector to supply DC power to the device. To test the

wireless CPE, install another RJ45 plug to the other end of your exterior CAT-5 cable and

connect this end to the PoE box in the socket marked ANTENNA. Also connect one end of the

supplied 7 foot CAT5 patch cable in the socket marked COMPUTER. The other end of this 7

foot cable will plug into the Ethernet port of your computer or into a hub or switch port. Plug the

supplied 12 volt 1 amp supply into a standard 110VAC outlet or power strip. Plug the other end

of this DC supply into the PoE box in the socket marked DC.

WARNING: Make sure that the antenna is pointed away from any humans or animals while

power is applied! A safe distance is approximately 18 inches or more.

The PoE injector box may be placed on the floor or mounted anywhere near the computer, hub,

switch or router.

Crossover

Switch

RJ45

Jack

Reset to

Factory

Default

Reboot

Table des matières

Autres manuels Telex Communications Matériel réseau

Telex Communications

Telex Communications 2472AA Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur