Teledyne Lecroy Frontline SD Manuel utilisateur

Frontline Technical Support: Phone +1-434-984-4500 or email tech_support@fte.com

Quick Start

Guide

Computer System Requirements

Supported Systems

lOperating System: Windows 7/8/10

lUSB:USB 2.0 and later

Minimum Requirements

lProcessor: Core i5 at 2.7 GHz

lRAM: 4 GB

lFree Hard Disk Space on C: drive: 20 GB

Install Software

lFrom Download: Download the latest ComProbe installer

from FTE.com. Once downloaded, double-click the

installer and follow the directions.

http://www.fte.com/sd-soft

1. Hardware Setup - Part 1

Once you have installed the software and the device drivers, the next step is to set up the hardware.

Provided with the Frontline SD hardware is one of two Secure Digital (SD) Input/Output (IO) adapters: 1) the standard SD card adapter,

and 2) the micro SD card adapter. Provided with each is a cable that must be connected to the adapter prior to the connecting the

adapter to the Frontline SD hardware. The following tables lists the Frontline SD Hardware pinout, with corresponding cable color-code

and the adapter pinout. In addition the table shows the pin designation for the SD 4-bit and 1-bit high-speed mode and the SPI mode.

Pin SD 4-bit Mode SD 1-bit Mode SPI Mode

1 CD/DAT3 Data Line 3 - - CS Card Select

2 CMD Command Line CMD Command Line DI Data Input

3 VSS1 Ground VSS1 Ground VSS1 Ground

4 VDD Supply Voltage VDD Supply Voltage VDD Supply Voltage

5 CLK Clock CLK Clock SCLK Clock

6 VSS2 Ground VSS2 Ground VSS2 Gound

7 DAT0 Data Line 0 DATA Data Line DO Data Output

8 DAT1 Data Line 1/Interrupt IRQ Interrupt IRQ Interrupt

9 DAT2 Data Line 2/ Read Wait RW Read Wait - -

Table 1 - SDIO Pinout

Frontline Technical Support: Phone +1-434-984-4500 or email tech_support@fte.com

Standard SD Adapter and Cable

Micro SD Adapter and Cable

Frontline

Hardware

Adapter Cable Wire

Color

Standard Adapter

Pin/Label

Micro Adapter

Pin/Label

GND Black 4/GND 4/GND

CLK Brown 7/CLK 6/CLK

CMD Red 3/CMD 3/CMD

DAT0 Orange 9/D0 7/DAT0

DAT1 Yellow 10/D1 8/DAT1

DAT2 Green 1/D2 1/DAT2

CD Blue 5/CD 2/CD

Blue* 5/D3* -

VDD Purple 6/VCC 5/VCC

* 4-bit mode

Table 2 - Frontline SD Adapter Wiring List

Frontline Technical Support: Phone +1-434-984-4500 or email tech_support@fte.com

Connect Cable to Adapter

1. Refer to the SDIO Pinout table and the Frontline SD Adapter Wiring list for the SD mode and

adapter you will be using.

2. Identify the wire color associated with the pin on the adaper for the appropriate mode.

3. Place the cable wire free end pin over the appropriate pin on the adapter and gently push on

until fully seated.

Connect Frontline SD Hardware

1. Plug the standard SD card adapter with the connectors into the 10 pin slot of the Frontline SD

hardware by matching the color coding on the wires to the label on the hardware .

SD2.0 Hardware Interface

2. On the other side, attach the USB cable to the USB Mini B receptacle ().

SD 2.0 Hardware Interface - Analysis Side Showing USB mini-B Receptacle

That is it for the hardware setup right now. We are not done yet, but after you start the application and make some configurations

settings, you will set up the rest of the hardware then. That comes in Hardware Setup – Part 2. But for now, let's continue to the next

section.

Frontline Technical Support: Phone +1-434-984-4500 or email tech_support@fte.com

2. Selecting Data Capture Method

Now that the test devices are on, the SD hardware properly

connected to the PC, the next step is to open the Frontline software.

Open "Frontline (version #)” from the Start menu or from the

Desktop folder (2). The launch wizard will appear:

Double click SD 2.0 to open the Control window.

3. Hardware Settings

The Hardware Settings dialog is used to select a device to sniff/scan. To access the Hardware Settings dialog:

Select Hardware Settings from the Options menu on the Control window

Select an SD unit from the drop-down list and click the OK button.

If no SD units are found, the list will be blank. You can also select Refresh

List to make sure the list is up to date.

Frontline Technical Support: Phone +1-434-984-4500 or email tech_support@fte.com

4. I/O Settings

The I/O Settings dialog for the Frontline SD unit has three radio buttons which

you use to select the Physical Layer. Generally, you will not change default

settings shown.

The default for Physical Layer Selection is SDIO, which you will use the

majority of the time.

If you know the Physical Layer is a Serial Peripheral Interface, select SPI.

If you are not sure if the Physical Layer is SDIO or SPI, select Autodetect.

The software will attempt to automatically determine the physical layer and

select it for you. Note, however, that Autodetect is not accurate every time.

The default Voltage Level Selection is 3.3 V.

Click on the OK button when you have completed your I/O selections.

5. Start Capture

You might be thinking why I should select Start Capture before the hardware setup

is complete. You select Start Capture first is so that all pre-connection traffic is

captured. If you connect all the hardware before starting capture, you might miss

data.

So, now that the SD hardware is installed, devices

turned on and identified. It's time to sniff the

communication between the devices.

Select Start Capture on the Control window toolbar

or from the Control window Live menu.

6. Hardware Setup - Part 2

You have already seen how to connect the SD card adapter to the Frontline SD hardware and the USB cable to the analysis PC. Now let's

continue with the rest of the hardware setup.

There are two ways to complete the setup. First let's look at what to do if you are using the card that fits in the slot on the IC board.

Then we will identify what to do if you want to wire the Pin Header because you do not want to use the standard SD form factor

connection.

Frontline Technical Support: Phone +1-434-984-4500 or email tech_support@fte.com

Device Under Test Connection

1. Insert the Device under Test (DUT), such as a micro SD MMC memory card into the slot on the IC board ().

Device Under Test Connection Setup

2. Insert the other end of the IC board into the SD slot on the test PC ().

Plugging IC Board to the Analysis PC

That is the complete hardware setup if you are using a memory card. It is different if you want to connect directly to the Pin

Header.

Pin Header Connection

In addition to using the standard connection, you can also connect directly to the Pin Header on the IC board. To do that, follow the wire

schematic in , below.

Frontline Technical Support: Phone +1-434-984-4500 or email tech_support@fte.com

Pin Header

Once you have made the connections to the Pin Header, you are ready to capture and analyze data. With this method you do not have

to plug the board into the SD slot on the analysis PC.

If you have done everything correctly, you will start capturing data.

For information on analyzing data with Frontline software, please see the Frontline User Manual, in the Documentation folder under

the Frontline <version #> desktop folder.

7. Analyze Data

From the Control window toolbar select the following icons to

view and analyze the captured data.

lEvent Display - for framed data, used to conduct

byte-level analysis.

lFrame Display - for framed data, used to conduct

protocol-level analysis.

lExtract Data/Audio - pull out data from various decoded protocols. Once you have extracted the data, you can save them

into different file types, such as text files, graphic files, email files, .mp3 files, and more.

This quick start guide provides sufficient information to begin the data capture. Detailed hardware and software information is

contained in the ComProbe SD User Manual. The manual is available on FTE.com.

The Bluetooth SIG owns the Bluetooth word mark and logos, and use of such marks is under license.

Publish date: 1/17/2017

Table des matières

Autres manuels Teledyne Lecroy Instrument de mesure

Teledyne Lecroy

Teledyne Lecroy PP016 Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy Frontline Sodera LE Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy PCI Express 5.0 U.2 Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy HVD3000 Series Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy HVD3102 Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy Frontline X240 Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy AP033 Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy WaveLink Series Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy PP006C Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy 280 Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy WavePulser 40iX Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy ZD500 Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy 980 Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook SierraNet M168 Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy M41h Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy USB Advisor T3 Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy ADP300 Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy Summit T416 Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy PP026-1 Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy HDA125 Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy WaveRunner 8000-R Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy DL03-ISO Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy RP4030 Manuel utilisateur

Teledyne Lecroy

Teledyne Lecroy PP008 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur