Tektronix FCA3100 Series Guide de l'administrateur

How-To Guide Continuous Measurements with Zero Dead-time

Continuous Measurements with Zero Dead-time

FCA3100 Series

How-To Guide

How-To Guide Continuous Measurements with Zero Dead-time

2 www.tektronix.com/frequencycounter

Tektronix FCA3100 Series Timer/Counter/Analyzer introduces the concept of Continuous Data

Output with Zero Dead-time. While this How-to Guide will focus on continuous measurement for

the FCA3100 series products, it will also describe the basic functionality of measuring and

streaming data and the differences of this between the FCA3000 and FCA3100 Series products.

1. The FCA3000/FCA3100 Measuring and Output Data Transfer Modes

Let’s begin with a summary of the different measurement and output data transfer modes in the FCA3000

and FCA3100 series products.

The FCA3000 and FCA3100 Series products can operate in several different measuring and data transfer

modes:

Single (individual) measurements

Block measurements Zero-dead-time block measurements

Zero-dead-time single measurements

(FCA3100 series only)

Mode Local Operation Remote Operation

FCA3100 FCA3000 FCA3100 FCA3000

Single

measurements

(with dead-time)

Values mode Values mode READ?. INIT+FETCH?

GET INIT +TALK ONLY READ?.

INIT/FETCH? GET

Block

measurements

(with dead-time)

Analyze mode of

any measurement Analyze mode of

any measurement READ:ARR?

INIT/FETCh:ARRay? READ ARR?

INIT/FETCH ARR?

Zero-dead-time

single

measurements

Freq BtB,

Period BtB, TIE Not available READ?. INIT+FETCH?

GET INIT +TALK ONLY Not available

Zero-dead-time

block

measurements

Freq BtB,

Period BtB,

TIE &

Analyze mode

Not available READ:ARR?

INIT+FETCh:ARRay? of

Freq BtB, Period BtB, TIE

(1-timestamp/value);

Or Raw timestamp

(4-timestamp/value)

READ ARR?

INIT/FETCH ARR? of

Raw timestamp

(4-timestamp/value)

Mode Max speed (calculated results/second)

FCA3100 FCA3000

Single measurements

(with dead-time) GET: 650/s TALK ONLY: 4000/s GET: 500/s

Block measurements

(with dead-time) READ:ARR?: 15K Sa/s READ ARR? 5K Sa/s

Zero-dead-time

block measurements with dead-

time between blocks

READ:ARR?: 15K Sa/s, 250K Sa/s

to internal memory of 3.75MB READ:ARR?: 15K Sa/s, 250K Sa/s

to internal memory of 750KB

Continuous zero-dead-time

block measurements ARM:COUNT INF

READ:ARRay:? 10K Sa/s Not available

How-To Guide Continuous Measurements with Zero Dead-time

3 www.tektronix.com/frequencycounter

Single Measurements

READ?

INIT+FETCH?

GET

Single measurements mean that you do one measurement at a time and transfer to the display and to the

data outputs (GPIB or USB). This mode has a dead time between measurements of approx. 2 ms, when you

trigger the counter’s individual measurements, one by one, via the GET command (Group Execute Trigger),

from the connected controller. The internal measurement memory buffer is not involved in this mode.

Using the above commands single measurements, you can control exactly when you want to initialize (start)

the measurement. The communication process is simplified:

Controller talker /FCA3000 or FCA3100 listener: “start measurement” (GET)

Controller talker / FCA3000 or FCA3100 listener: “send result” (FETCH?)

FCA3000 or FCA3100 talker/ Controller listener: “sending result data”

Controller talker / FCA3000 or FCA3100 listener: “start next measurement” (GET) …

FCA3100: In addition to the FCA3000 modes, the FCA3100 has an additional output mode;

Talker only (SYSTem:TALKonly ON)

Talker only differs from the GET-triggered individual measurements in that the counter will be triggered once

and after that the counter will output measurement data at the highest possible rate, without waiting for

subsequent trigger commands (GET) from the controller. This reduces the transfer overhead since the

controller is not taking control between the measurements. The controller cannot initialize individual

measurements and the measurement data continues to be sent until the controller stops the transfer via the

Interface Clear command or by pressing the ESC key on the counters front panel.

The dead-time between measurements in this “real-time” transfer mode is <250 microseconds. To reach this

throughput rate, the communication process is simplified:

Controller talker /FCA3000 listener: “go to Talker only mode and start measurement”

FCA3000 talker/ Controller listener: “sending result data”

Etc…

How-To Guide Continuous Measurements with Zero Dead-time

4 www.tektronix.com/frequencycounter

Block Measurements

READ:ARR?

INIT + FETCH:ARR?

Block measurements mean that you set up a certain measurement function, e.g. frequency, and trigger a

block measurement sequence from the controller. Then the individual measurement results are transferred

one-by-one to the internal memory and stored, until the set number of samples has been reached. After that

the memory contents can be sent to the controller using the FETCH ARRAY command.

The dead-time between measurements is significantly smaller, only 4-8 microseconds. To reduce the dead

time to a minimum, you can for example disable calibration of interpolators (CAL:INT:AUTO OFF). To

maximize throughput you can also turn off the display (DISP:ENAB OFF) and use Packed data format

(FORM:PACK).

Using these modes of fetching data, you do a block transfer and cannot see the individual measurements

until the whole block is received. You can control via SW exactly when you want to initialize (start) the block.

The procedure for block measurements in the FCA3000 is pure sequential. First you measure and store ALL

values in the block in internal memory, then all measurements in the block are processed (calculated and

formatted), and finally the block is transferred to the PC. The measurement function can be any standard

function with dead time (e.g. Frequency, Period, Vp-p) or the raw time-stamping function (zero-dead-time).

This means there is always a gap of data due to the dead time between blocks in the data output, even if

individual blocks contain zero-dead-time data. In the FCA3000, true zero-dead-time measurements can only

be made up to 750K Samples (internal memory limit), after that there must be a gap in the data.

Zero Dead-time Data

Measure Gap in the data Gap in the data

Process

Transfer

How-To Guide Continuous Measurements with Zero Dead-time

5 www.tektronix.com/frequencycounter

Zero Dead-Time Single Measurements

Only the FCA3100 features zero-dead-time single measurements, accessible from both the front panel in

local operation, as well as in remote bus operation. There are three pre-defined measurements; frequency

back-to-back, period back to back and TIE (Time Interval Error).

In frequency or period back-to-back you read the number of elapsed input trigger events or input cycles (Ni)

and the elapsed time (Ti) at intervals defined via the measuring time setting, every time you read the elapsed

events and time, you calculate the Frequency or Period on-the-fly as:

Ni– Ni-1 Ti– Ti-1 Ni– N0

Freq (i) = Per (i) = TIE (i) = Ti– T0 –

Ti– Ti-1 Ni– Ni-1 FREF

Note that the Frequency value is always, per definition, the average number of cycles/s during the

measurement time. When measuring frequency, the input signal is divided by 2 before it is time-stamped,

which means the minimum frequency measurement time is over 2 cycles.

Period back-to-back and TIE has no input divider, and is a single period as long as Ni= Ni-1 + 1. This is the

case for input frequencies up to approximately 250 KHz. At higher frequencies, up to 160 MHz, the value is

the average period back-to-back.

Zero Dead-Time Block Measurements (Raw Time-stamping Data)

Both FCA3100 and FCA3000 series products perform zero-dead-time “raw” time-stamping measurements as

a block measurement function only, which is not accessible from the front panel. From the GPIB or USB bus

you set up a certain block sizes, select a pacing time from 4 microseconds and up, and start the time-

stamping measurement (FUNC:TSTA). This mode will then store the number of accumulated and time-

stamped input trigger events, in groups of 4, without losing any single cycle up to 160 MHz input signals.

[E(i),Tp1(i)] [E(i)+1,Tp2(i)] [E(i+1),Tp1(i+1)] [E(i+1)+1,Tp2(i+1)]

[0,Tn1(i)] [0,Tn2(i)] [0,Tn1(i+1)] [0,Tn2(i+1)]

Event Event Event Event

no E(i) no E(i+1) no E(i)+1 no E(i+1)+1

E(i) is the i:th sample of accumulated input cycles (ALL trigger events are counted and accumulated up to

160 MHz on input A or B,). E(i)=0 for the negative slopes, and the accumulated number of input cycles for

the positive slope.

Tp1(i) is the timestamp of the first positive trigger event

Tp2(i) is the timestamp of the second positive trigger event

Tn1(i) is the timestamp of the first negative trigger event

Tn2(i) is the timestamp of the second negative trigger event

How-To Guide Continuous Measurements with Zero Dead-time

6 www.tektronix.com/frequencycounter

Please note that the first trigger event that occurs after the pacing time, may be a negative as well as a

positive trigger slope, so the sequence of the 4 timestamps may be:

pos – neg – pos – neg OR neg – pos – neg – pos .

The way to identify this is to look at the event number which is 0 for negative slopes and is a positive integer

for positive slopes.

In addition to the FCA3000 raw time-stamping mode, the FCA3100 can also measure Frequency and Period

Back-to-Back plus TIE, as zero-dead-time block measurements.

Just like normal block array measurements, this measurement can continue at maximum speed a limited

time until the internal memory buffer is filled, after 3.75M Samples (FCA3100) respectively 750k Samples

(FCA3000). After that the memory must be read and emptied before the next block of zero-dead-time data

can be measured again.

The FCA3100 can also make continuous “streaming” measurements of zero-dead-time data for an unlimited

time, as described below.

2. Continuous Streaming Output Mode

This unique FCA3100 output mode is basically a normal block measurement mode, however with the

exception that there are parallel processes for storing data in internal memory, processing stored data and

outputting data. Furthermore the block can have an unlimited size in FCA3100.

Zero dead-time data (<10K measurements/s)

Measure

Process

Transfer

Continuous measurements come in two flavors "Fetch on the Fly" and "Overwrite Mode" as described below.

Fetch on the Fly

This is simply the ability the fetch the results from a normal block measurement that fits in the buffer while it

is still running. One thing to consider though is that while the measurement hasn't finished, you may not

know how many samples are actually available for fetching. So, you use the FETC:ARR? MAX functionality

(see below).

Overwrite Mode

This is the case when you specify a larger total number of measurements than will fit in the memory, that is

>3.75M samples. As the buffer fills up, old values are overwritten with the new ones. This is done in such a

way that it should always (with reasonable measurement speed) be safe to fetch on the fly. That is, the data

that is overwritten should never be the data that is in progress of being fetched.

For almost all measurement functions the method used is the following. The memory buffer is divided into six

segments, each of which is at any one time dedicated to some particular usage (segments where data is

being fetched from and segments where new data is written to). The roles of the segments can be switched

around as needed.

How-To Guide Continuous Measurements with Zero Dead-time

7 www.tektronix.com/frequencycounter

As long as the fetching speed more or less keeps up with the measurement speed, this works out much the

same as a regular circular buffer would do. But when you do not fetch sufficiently fast, or when you stop the

measurement and the buffer contains a lot of un-fetched data, there is always one or two segment's with

valid newest result data remaining in the buffer, i.e. between one sixth and one third of the buffer (600K to

1200K measurements).

If the instrument is set up to measure faster than it can handle in overwrite mode, you will eventually end up

with invalid data in the buffer. Most often invalid timestamps, but also invalid measurement results can

occur. Internal tests will detect when this happens, and abort the measurement and put a -321, "Storage

fault" error in the error queue, indicating that the buffer contents can't be trusted (but data is still available for

fetching).

The measurement speed limit in overwrite mode depends on a lot of factors, including for example how fast,

and in what way, the user fetches data on the fly. For this reason it's hard to set any firm rules for

measurement speed recommendation.

Currently, one limit is enforced; in overwrite mode the pacing time used is minimum 50 microseconds,

regardless of actual setting. This is to prevent the user from “choking” the instrument.

Practical tests show that data capture rates of >10K Sa/s is likely to cause invalid data at some point during a

long measurement. To be on the safe side, set a pacing time of more than 100 microseconds, with some

margin. Measurements with more complex calculations such as Phase, requires longer pacing time than

simpler measurements such as Period Single.

3. New SCPI Commands or Changed Behavior in FCA3100

FETCh:ARRay? <number of samples> | MAX (FCA3100 only)

When specifying <number of samples>, the instrument will wait until that number is available before

responding. This could result in long waits if the measurement doesn't proceed as expected.

When using the "MAX" parameter, the instrument will respond immediately with as many samples as

currently possible. The number of samples in the response is limited by the number of un-fetched samples

currently remaining in the buffer and the FORMAT:SMAX setting.

Error; -230,"Data corrupt or stale", is generated when there is no valid sample(s) to fetch at all from the

buffer.

Error -224,"Illegal parameter value" error is generated if you try to fetch a larger number of samples than

remains to fetch in the buffer. This includes also the case of using the "MAX" parameter when already at the

end of the buffer, and you have already fetched all samples.

How-To Guide Continuous Measurements with Zero Dead-time

8 www.tektronix.com/frequencycounter

ABORt

ABORT no longer invalidates already finished results when breaking an array measurement. This means you

can now fetch the partial result after the abort.

FORMat:SMAX <number>

Where “number” is any integer between 4 and 10000. Default setting is 10000 (not affected by *RST). This

command is intended for use with any controller or application program that have problems with reading

large amounts of data, but where the FETC:ARR? MAX functionality is wanted. To query the actual setting

use:

FORMat:SMAX?

When using the "MAX" parameter, the instrument should always respond within a predictable time. Actual

response time depends primarily on the number of samples in the response and the FORMat settings used

(ASCii being particularly slow, REAL is fast and PACKed is fastest), and to some extent the actual

measurement function. When no new measurement since the latest fetch is available in the buffer (and not

at the end of it), FETC:ARR? MAX will give a "zero samples" response, ie empty string in case of format

ascii, and an empty binary data packet ("#10") in the case of format real or packed.

ARM:COUNt <number> | INFinity

ARM:COUNt?

The "INF" parameter is available in CNT91 only. It will cause the arm loop to continue endlessly. (Note: The

timestamp counter will overflow after approx 107 days of non-aborted operation, something that must be

taken care of in the application SW, if it is important to run continuously for more the 3 months.) When set to

INFinity, the query responds with "INF" (without the quotes).

Talker Only Mode

To switch on talker only mode:

SYSTem:TALKonly ON

Since now the FCA3100 will be talker “forever”, and will not listen to any programming command from the

controller via the normal handshake lines, there is no command “SYST:TALK OFF” available. Once you have

sent the command SYST:TALK ON to the counter, the FCA3100 will no longer respond to normal commands

via the data lines in the GPIB interface

To switch off Talker Only mode, you use the ESC key (C) on the front panel alternatively send an Interface

Clear (IFC) over GPIB.

Further settings to implement for successful high-speed talker only transfer are:

DISPlay:ENABle OFF.

FORMat REAL or FORMat PACKed.

ARM:COUNt 1

TRIGger:COUNt 1

INIT:CONT ON.

How-To Guide Continuous Measurements with Zero Dead-time

9 www.tektronix.com/frequencycounter

The measurement function can be any except the following:

Period average (smart calculation)

Frequency (smart calculation)

Time Interval (smart calculation)

Time-stamping

Voltage

Totalize

This means that Frequency BtB and Period BtB is OK, but not “smart” frequency where a regression line

fitting between several time-stamped data is used to improve the basic resolution.

Contact Tektronix:

ASEAN / Australasia (65) 6356 3900

Austria 00800 2255 4835*

Balkans, Israel and other ISE Countries +41 52 675 3777

Belgium 00800 2255 4835*

Brazil + 55 (11) 3759 7600

Canada 1-800-833-9200

Central East Europe, Ukraine and the Baltics +41 52 675 3777

Central Europe & Greece +41 52 675 3777

Denmark +45 80 88 1401

Finland +41 52 675 3777

France 00800 2255 4835*

Germany 00800 2255 4835*

Hong Kong 400-820-5835

India 000-800-650-1835

Italy 00800 2255 4835*

Japan 81 (3) 6714-3010

Luxembourg +41 52 675 3777

Mexico, Central/South America & Caribbean (52) 56 04 50 90

Middle East and Africa +41 52 675 3777

The Netherlands 00800 2255 4835*

Norway 800 16098

People’s Republic of China 400-820-5835

Poland +41 52 675 3777

Portugal 80 08 12370

Republic of Korea 001- 800-8255-2835

Russia & CIS +7 (495) 7484900

South Africa +41 52 675 3777

Spain 00800 2255 4835*

Sweden 00800 2255 4835*

Switzerland 00800 2255 4835*

Taiwan 886 (2) 2722-9622

United Kingdom & Ireland 00800 2255 4835*

USA 1-800-833-9200

European toll-free number. If not accessible, call: +41 52 675 3777

Contact List Updated 25 May 2010

For Further Information

Tektronix maintains a comprehensive, constantly expanding

collection of application notes, technical briefs and other

resources to help engineers working on the cutting edge of

technology. Please visit www.tektronix.com

covered by U.S. and foreign patents, issued and pending. Information in this

publication supersedes that in all previously published material. Specification

and price change privileges reserved. TEKTRONIX and TEK are registered

trademarks of Tektronix, Inc. All other trade names referenced are the service

marks, trademarks or registered trademarks of their respective companies.

9/2010 WWW 3CW-25883-1

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Tektronix Instrument de mesure

Tektronix

Tektronix 7L12 Manuel utilisateur

Tektronix

Tektronix 7D20 Manuel utilisateur

Tektronix

Tektronix RSA6100A Series Manuel d'utilisation et d'entretien

Tektronix

Tektronix TLA7AA1 Manuel utilisateur

Tektronix

Tektronix Keithley SourceMeter 2461 Manuel utilisateur

Tektronix

Tektronix THM550 Manuel utilisateur

Tektronix

Tektronix 7L5 Manuel utilisateur

Tektronix

Tektronix WFM4000 Series Manuel utilisateur

Tektronix

Tektronix DPO7OE Series Manuel utilisateur

Tektronix

Tektronix VM5000 Series Manuel

Tektronix

Tektronix RSA6100A Series Manuel d'utilisation et d'entretien

Tektronix

Tektronix Keithley 4200A-SCS Manuel utilisateur

Tektronix

Tektronix KEITHLEY 8011 Manuel utilisateur

Tektronix

Tektronix 82A00 Instructions d'installation et d'entretien

Tektronix

Tektronix 7L5 Manuel utilisateur

Tektronix

Tektronix RSA3408B Manuel d'utilisation et d'entretien

Tektronix

Tektronix 2715 Manuel utilisateur

Tektronix

Tektronix PSM3000 Series Manuel utilisateur

Tektronix

Tektronix 318 Manuel utilisateur

Tektronix

Tektronix CDC250 Manuel utilisateur

Tektronix

Tektronix TriMode P7700 Series Manuel

Tektronix

Tektronix RSA5100B series Manuel d'utilisation et d'entretien

Tektronix

Tektronix WCA230A Manuel d'utilisation et d'entretien

Tektronix

Tektronix 492, 492P Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur