Tektronix A622 Manuel utilisateur
A622
100 Amp AC/DC Current Probe
Instructions
Register now!
Click the following link to protect your product.
www.tek.com/register
*P070888306*
070-8883-06
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are
protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued
and pending. Information in this publication supersedes that in all previously published material. Specifications and price change privileges
reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
• In North America, call 1-800-833-9200.
• Worldwide, visit to www.tek.com find contacts in your area.
Important safety information
This manual contains information and warnings that must be followed by the user for safe operation and to keep the product in a safe
condition.
To safely perform service on this product, see the Service safety summary that follows the General safety summary.
General safety summary
Use the product only as specified. Review the following safety precautions to avoid injury and prevent damage to this product or any
products connected to it. Carefully read all instructions. Retain these instructions for future reference.
This product shall be used in accordance with local and national codes.
For correct and safe operation of the product, it is essential that you follow generally accepted safety procedures in addition to the safety
precautions specified in this manual.
The product is designed to be used by trained personnel only.
Only qualified personnel who are aware of the hazards involved should remove the cover for repair, maintenance, or adjustment.
Before use, always check the product with a known source to be sure it is operating correctly.
This product is not intended for detection of hazardous voltages.
Use personal protective equipment to prevent shock and arc blast injury where hazardous live conductors are exposed.
To avoid fire or personal injury
Observe all terminal ratings.
To avoid fire or shock hazard, observe all rating and markings on the product. Consult the product manual for further ratings information
before making connections to the product.
Do not exceed the Measurement Category (CAT) rating and voltage or current rating of the lowest rated individual component of a product,
probe, or accessory. Use caution when using 1:1 test leads because the probe tip voltage is directly transmitted to the product.
Do not apply a potential to any terminal, including the common terminal, that exceeds the maximum rating of that terminal.
Do not connect a current probe to any wire that carries voltages above the current probe voltage rating.
Do not operate without covers.
Do not operate this product with covers or panels removed, or with the case open. Hazardous voltage exposure is possible.
Avoid exposed circuitry.
Do not touch exposed connections and components when power is present.
Replace batteries properly
Replace batteries only with the specified type and rating.
Do not operate in wet/damp conditions.
Be aware that condensation may occur if a unit is moved from a cold to a warm environment.
Do not operate in an explosive atmosphere.
Keep product surfaces clean and dry.
Remove the input signals before you clean the product.
Important safety information
A622 100 Amp AC/DC Current Probe Instructions 3
Probes and test leads
Connect and disconnect properly.
Connect the probe output to the measurement product before connecting the probe to the circuit under test. Connect the probe reference
lead to the circuit under test before connecting the probe input. Disconnect the probe input and the probe reference lead from the circuit
under test before disconnecting the probe from the measurement product.
Do not connect a current probe to any wire that carries voltages or frequencies above the current probe voltage rating.
Inspect the probe and accessories.
Before each use, inspect probe and accessories for damage (cuts, tears, or defects in the probe body, accessories, or cable jacket). Do
not use if damaged.
Service safety summary
The Service safety summary section contains additional information required to safely perform service on the product. Only qualified
personnel should perform service procedures. Read this Service safety summary and the General safety summary before performing any
service procedures.
To avoid electric shock.
Do not touch exposed connections.
Do not service alone.
Do not perform internal service or adjustments of this product unless another person capable of rendering first aid and resuscitation is
present.
Disconnect power.
To avoid electric shock, switch off the product power and disconnect the power cord from the mains power before removing any covers or
panels, or opening the case for servicing.
Use care when servicing with power on.
Dangerous voltages or currents may exist in this product. Remove battery before removing protective panels, soldering, or replacing
components.
Terms in this manual
These terms may appear in this manual:
Warning: Warning statements identify conditions or practices that could result in injury or loss of life.
CAUTION: Caution statements identify conditions or practices that could result in damage to this product or other property.
Terms on the product
These terms may appear on the product:
• DANGER indicates an injury hazard immediately accessible as you read the marking.
• WARNING indicates an injury hazard not immediately accessible as you read the marking.
• CAUTION indicates a hazard to property including the product.
Important safety information
A622 100 Amp AC/DC Current Probe Instructions 4
Symbols on the product
When this symbol is marked on the product, be sure to consult the manual to find out the nature of the potential
hazards and any actions which have to be taken to avoid them. (This symbol may also be used to refer the user to
ratings in the manual.)
The following symbols(s) may appear on the product.
Important safety information
A622 100 Amp AC/DC Current Probe Instructions 5
Compliance information
This section lists the safety and environmental standards with which the instrument complies. This product is intended for use by
professionals and trained personnel only; it is not designed for use in households or by children.
Questions about the following compliance information may be directed to the following address:
Tektronix, Inc.
PO Box 500, MS 19-045
Beaverton, OR 97077, USA
tek.com
Safety compliance
This section lists the safety standards with which the product complies and other safety compliance information.
EU declaration of conformity – low voltage
Compliance was demonstrated to the following specification as listed in the Official Journal of the European Union:
Low Voltage Directive 2014/35/EU.
• EN 61010-1. Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use – Part 1: General
Requirements
• EN 61010-2-032. Particular requirements for handheld current clamps for electrical measurement and test equipment
U.S. nationally recognized testing laboratory listing
• UL 61010-1. Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use – Part 1: General
Requirements
Canadian certification
• CAN/CSA-C22.2 No. 61010-1. Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use – Part 1:
General Requirements
Additional compliances
• IEC 61010-1. Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use – Part 1: General
Requirements
• IEC 61010-2-032. Particular requirements for handheld current clamps for electrical measurement and test equipment
Equipment type
Test and measuring equipment.
Safety class
Class 2
Pollution degree description
A measure of the contaminants that could occur in the environment around and within a product. Typically the internal environment inside a
product is considered to be the same as the external. Products should be used only in the environment for which they are rated.
• Pollution Degree 1. No pollution or only dry, nonconductive pollution occurs. Products in this category are generally encapsulated,
hermetically sealed, or located in clean rooms.
Compliance information
A622 100 Amp AC/DC Current Probe Instructions 6
• Pollution Degree 2. Normally only dry, nonconductive pollution occurs. Occasionally a temporary conductivity that is caused by
condensation must be expected. This location is a typical office/home environment. Temporary condensation occurs only when the
product is out of service.
• Pollution Degree 3. Conductive pollution, or dry, nonconductive pollution that becomes conductive due to condensation. These are
sheltered locations where neither temperature nor humidity is controlled. The area is protected from direct sunshine, rain, or direct
wind.
• Pollution Degree 4. Pollution that generates persistent conductivity through conductive dust, rain, or snow. Typical outdoor locations.
Pollution degree rating
Pollution Degree 2 (as defined in IEC 61010-1). Note: Rated for indoor, dry location use only.
IP rating
IP20 (as defined in IEC 60529).
Measurement and overvoltage category descriptions
Measurement terminals on this product may be rated for measuring mains voltages from one or more of the following categories (see
specific ratings marked on the product and in the manual).
• Measurement Category II. For measurements performed on circuits directly connected to the low-voltage installation.
• Measurement Category III. For measurements performed in the building installation.
• Measurement Category IV. For measurements performed at the source of low-voltage installation.
Note: Only mains power supply circuits have an overvoltage category rating. Only measurement circuits have a measurement
category rating. Other circuits within the product do not have either rating.
Environmental compliance
This section provides information about the environmental impact of the product.
Product end-of-life handling
Observe the following guidelines when recycling an instrument or component:
Equipment recycling Production of this equipment required the extraction and use of natural resources. The equipment may
contain substances that could be harmful to the environment or human health if improperly handled at the
product’s end of life. To avoid release of such substances into the environment and to reduce the use of
natural resources, we encourage you to recycle this product in an appropriate system that will ensure that
most of the materials are reused or recycled appropriately.
This symbol indicates that this product complies with the applicable European Union requirements according to Directives
2012/19/EU and 2006/66/EC on waste electrical and electronic equipment (WEEE) and batteries. For information about
recycling options, check the Tektronix Web site (www.tek.com/productrecycling).
Compliance information
A622 100 Amp AC/DC Current Probe Instructions 7
Getting Started
Overview
The A622 current probe enables a general purpose oscilloscope to display AC and DC current signals up to 100 amps Peak (70 A RMS).
The A622 current probe can also make AC and DC measurements with a multimeter by using the BNC-to-banana plug adapter available
as a recommended accessory (see Replaceable Parts on page 15).
Figure 1: A622 AC/DC Current Probe
The following table highlights the controls and indicators on the A622 current probe.
Table 1: A622 controls and indicators
Control/Indicator Description
Current flow symbol. The arrow shows the polarity convention of the probefor measuring current flowing
from positive to negative.
Zero adjustment. Rotate to adjust the probe output to zero when there is no current present. It can also be
used to offset a DC signal component. Zeroing is not needed for AC measurements unless your instrument
cannot isolate a DC component (if present).
OFF/Range switch. Slide the switch from OFF to either the 10 mV/A or 100 mV/A range. When either range
is selected, the probe is turned on, and the green battery indicator lights. If the indicator does not light, see
Battery Notes on page 11.
Battery indicator. The green battery indicator lights when the probe is turned on. For more information, see
Battery Notes on page 11.
Overload indicator. The red overload indicator lights if the measured signal is greater that the selected
range capacity. Switch the probe to 10 mV/A if possible, or remove the probe from the circuit.
Getting Started
A622 100 Amp AC/DC Current Probe Instructions 8
Operating Basics
Before using the probe, the batteries must be installed; see Battery Installation on page 11.
Warning: Personal injury or damage to the probe can result if you clamp the probe onto circuits with voltages greater than
600 VAC. Do not clamp the probe onto circuits with higher voltages. Always connect the probe to the instrument before clamping
onto the circuit under test.
1. Connect the probe BNC connector to the oscilloscope input. Start by setting the oscilloscope channel vertical coupling to DC volts and
the vertical deflection to 0.1 V/div.
2. Move the OFF/Range switch to the 10 mV/A or 100 mV/A position to power on the probe.
The A622 current probe has a green LED power/battery indicator. If the LED does not light, replace the battery.
3. Use the ZERO adjustment to zero or offset the probe output.
4. Connect the probe to the circuit by opening the jaws and clamping around the conductor. See Figure 2 on page 9.
Note: Clamping around both the "hot" and neutral wires may give you a zero reading.
(Remember to unclamp the probe from the conductor before disconnecting it from your meter or instrument.)
Figure 2: Connecting the A622 current probe
5. Adjust the probe and channel as necessary to get a clear view of the signal. Set the channel to DC volts to see both the AC and DC
currents; set the channel to AC to see the AC current only.
The current drawn by some devices looks much different than that of others. While the RMS current may be low, the momentary peaks can
be quite high. The following figures shows the difference between the line current drawn by a resistive load and a motor controller.
Getting Started
A622 100 Amp AC/DC Current Probe Instructions 9
Figure 3: Typical current waveforms
If you are using the A622 current probe with a multimeter, connect the probe with the recommended BNC-to-banana adapter. Connect the
black lead to the meter COM, and the red lead to the VΩ input.
To measure only AC current, set the meter to measure AC volts.
To measure DC current, set the meter to measure DC volts. Note the current convention arrow on the probe to get the proper polarity
reading.
To increase the measurement sensitivity of the A622 current probe, loop additional turns of the wire under test through the jaws. See
Figure 4 on page 10. The sensitivity of the A622 current probe is multiplied times the number of loops in the jaws. For example: 10 mV/A
× 4 turns = 40 mV/A.
CAUTION: To prevent damage to the probes, do not force the jaw closed. If you cannot close the jaw around the conductor(s),
either reduce the number of conductors you are measuring, or, if possible, take your measurement on a smaller conductor.
Figure 4: Increasing the sensitivity
Getting Started
A622 100 Amp AC/DC Current Probe Instructions 10
Autres manuels pour A622
2
Table des matières
Autres manuels Tektronix Instrument de mesure
Tektronix
Tektronix RSA5100B series Instructions d'installation et d'entretien
Tektronix
Tektronix RSA7100A Manuel
Tektronix
Tektronix SPG8000A Manuel utilisateur
Tektronix
Tektronix TLA6400 Series Manuel utilisateur
Tektronix
Tektronix 82A00 Instructions d'installation et d'entretien
Tektronix
Tektronix 475 Manuel utilisateur
Tektronix
Tektronix 1502C Manuel utilisateur
Tektronix
Tektronix 7L5 Manuel
Tektronix
Tektronix KEITHLEY 8606 Manuel utilisateur
Tektronix
Tektronix RSA5106B Instructions d'installation et d'entretien
Tektronix
Tektronix RSA6114A Manuel
Tektronix
Tektronix WVR7000 Series Manuel
Tektronix
Tektronix 491 Manuel utilisateur
Tektronix
Tektronix MTM400 Manuel utilisateur
Tektronix
Tektronix CSA 803C Manuel utilisateur
Tektronix
Tektronix TLA7AA1 Manuel utilisateur
Tektronix
Tektronix Keithley 2601B-PULSE Manuel utilisateur
Tektronix
Tektronix 7D20 Manuel utilisateur
Tektronix
Tektronix WVR5200 Series Instructions d'installation et d'entretien
Tektronix
Tektronix KEITHLEY 4200A Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur