Techsphere VP-II M Manuel utilisateur

Installation Guide

VP-II M

Hand Vascular Pattern Recognition System

The Second Generation

VP-II M Hand Vascular Pattern Recognition System

Installation Guide

Techsphere Co. Ltd. makes no warranty for the use of its products

assumes no responsibility for any errors that may appear in this

document and makes no commitment to update the information

contained in this document. Techsphere Co. Ltd. reserves the right to

change or discontinue this product at any time.

Preface: Read this section before starting.

Thank for your choosing the Techsphere VP-II M Hand Vascular

Pattern Recognition system. This installation guide describes how to

install the components of the VP-II M system the basic model of

Techsphere’s VP-II Hand Vascular Pattern Recognition system.

It is recommended that installation be performed by a trained

technician. Please contact your local Techsphere sales representative

for an installation visit. Only a Techsphere technical specialist or

local sales representative should open components of VP-II systems

in order to perform repairs or to expand the system.

Installation must be performed according to the instructions in this

installation guide. If the VP-II M system is installed improperly the

system may not function properly. Symptoms of improper

installation range from complete operation failure to lowered system

performance.

In order to connect a VP-II M system to a host PC a VP-II Converter

is required. A VP-II Data Repeater is required to extend effective

cable length for any system in which components of the VP-II

system are separated by more than 100 meters.

It is strongly recommended that you read the entirety of this guide

before installing the VP-II M Hand Vascular Pattern Recognition

system. For your own safety and for the long life of the system

handle the system carefully according to the procedures and

suggestions in this manual.

Don’t hesitate to contact your local Techsphere sales representative

or Techsphere customer support ([email protected])

if you determine that you need service support information or

replacement equipment.

Table of Contents

Preface: Read this section before starting. ................................................................ i

Table of Contents ..................................................................................................... ii

Chapter 1 Before installing the VP-II M system................................................ 3

1.1 Installation environment......................................................... 3

1.2 Required cables ...................................................................... 3

1.3 Included items ........................................................................ 4

Chapter 2 Installing the VP-II Scanner .............................................................. 5

Chapter 3 Installing the VP-II Controller........................................................... 7

Chapter 4 Connecting to a door-lock (optional)................................................. 9

Chapter 5 System configuration....................................................................... 10

Chapter 6 Connecting the VP-II Converter...................................................... 12

Chapter 7 Preparing RS-422 connection cables ............................................... 13

Chapter 8 Checking after installation............................................................... 14

Chapter 9 Safe use and handling...................................................................... 15

Chapter 10 Service contact information............................................................. 16

10.1 Customer Service ................................................................. 16

10.2 E-mail................................................................................... 16

10.3 Web Page.............................................................................. 16

Product Regulatory Information ........................................................................... 17

1.3 Included items

Before installing your VP-II M system verify that all of the items

pictured below are included in your VP-II M package:

VP-II scanner

RJ-45 cable

switch mode power supply

SMPS

User

’

s guide

two (2) RJ-45

connectors

seven (7) screws

VP-II controller

bracket

Installation

guide

keys

Cable (4m)

Wall

sticker

Chapter 2 Installing the VP-II Scanner

The VP-II Scanner must be installed in a place where it will not be

exposed to direct sunlight. Reflected sunlight may interfere with the

system as well. High humidity rain and excess dust may interfere

with the functioning of the VP-II system; install the Scanner away

from such elements.

Do not install the VP-II Scanner where the floor is inclined.

Install the VP-II Scanner at a height of 1015-1045mm from the floor

and 100mm from the doorframe. If there is a wall beside the door

VP-II Scanner should be at least 200mm apart from the wall.

Put the bracket on the place for installing the VP-II Scanner and

make a hole after checking the hole location for cabling. Fix the

bracket on the wall using the bracket screws.

Power must be applied only after finishing all connections. Do not

perform any disconnection or connection after power is applied.

015

045

Door

100mm

200mm

Floor

Wall

After preparing the scanner cables connect the cables to the scanner

and then attach the scanner on the bracket. Make sure that the

scanner fit into the bracket all the way in. You may need some force.

When the scanner is fixed turn the security lock key clockwise and

then fix the scanner.

bracket

Bracket screws

Hole location for cabling

wall

Screw type: 4Φ×

××

×30 mm

RJ-45 cable

(4m)

Open

Chapter 3 Installing the VP-II Controller

Install the Controller on the inner wall near enough to the VP-II

Scanner that it can be reached with the cables provided. The

Controller cable length should not exceed 4m. Select a place where

access for maintenance is convenient. Ensure that a power outlet is

near.

Make a hole in the wall for affixing the controller; then insert a screw

approximately two thirds of the way in. Fix the controller on the wall

by hooking it on the screw.

Connect the power cable and the controller cable. Ensure that the

connection cable is not exposed to the outside.

Screw type : 3

××

20mm

SMPS

DI S/W

VP-II Scanner

Door Lock

For a stand-alone VP-II system consisting of only one VP-II M

system (one Scanner and one Controller) set the dip switch of the

VP-II Controller as shown below. For extension to a network

environment (multiple Scanners and multiple Controllers) see the

VP-II NCU installation guide.

Factory setting Single V -II M

system mode

Please do not adjust settings unless you are an installer or a

technician.

Table des matières

Autres manuels Techsphere Contrôleurs d'accès IP

Techsphere

Techsphere VP-II X Manuel utilisateur

Manuels Contrôleurs d'accès IP populaires d'autres marques

ZKTeco

ZKTeco SpeedFace-V5L Manuel utilisateur

Jantar

Jantar REX A-1-9 Manuel utilisateur

2N Access Unit Feuille d'instructions

Kedacom

Kedacom KSCA120 Series Manuel utilisateur

H3C

H3C WX2880X Manuel utilisateur

G4S

G4S S870-EX Mode d’emploi

PRASTEL

PRASTEL M2000PE Manuel utilisateur

Allegion

Allegion interflex IF-281 Cylinder Manuel utilisateur

TECOM

TECOM TS1067E Manuel utilisateur

Fermax

Fermax Memokey 100C Guide de l'utilisateur

Fermax

Fermax CITYLINE MEMOKEY Mode d’emploi

Software House

Software House iSTAR Pro 2U RM Mode d’emploi

AKCP

AKCP SP+ Manuel utilisateur

Bpt

Bpt HNA/102 Manuel utilisateur

Civintec

Civintec CV9601T-T-1F Manuel utilisateur

BioMax

BioMax N-X90W Manuel utilisateur

ZKTeco

ZKTeco OP-200 Manuel utilisateur

FingerTec

FingerTec s-Kadex Manuel utilisateur