Technotape HPM.MUG.350.005 Manuel utilisateur
MUG PRESS
MOKKENPERS
WITH HEAT ELEMENT FOR STANDARD MUGS Ø7,5 ~ 9,5 CM
MET VERWARMINGSELEMENT VOOR STANDAARD MOKKEN Ø7,5 ~ 9,5 CM
HPM.MUG.350.005
HPM.MUG.350.005
USER MANUAL
HANDLEIDING
FIRST TIME USE
CONTENTS
2
3
4
5
6
7
ACCESSORIES
F.A.Q.
FAHRENHEIT - CELSIUS CONVERSION
USING THE MUG PRESS
CONTROL UNIT SETTINGS
Contents
Changing accessories
Mug Press accessories
Frequently asked questions
Instructions
System instructions
Safety instructions
MUG PRESS
WITH HEAT ELEMENT FOR STANDARD MUGS Ø7,5 ~ 9,5 CM
HPM.MUG.350.005
USER MANUAL
14 WARRANTY CONDITIONS
1
MOKKENPERS
MET VERWARMINGSELEMENT VOOR STANDAARD MOKKEN Ø7,5 ~ 9,5 CM
HPM.MUG.350.005
HANDLEIDING
EERSTE GEBRUIK
INHOUD
8
9
10
11
12
13
15
ACCESSOIRES
F.A.Q.
FAHRENHEIT - CELSIUS GRADENTABEL
GARANTIEVOORWAARDEN
DE MOKKENPERS GEBRUIKEN
BEDIENINGSPANEEL INSTELLEN
Inhoud
Accessoires verwisselen
Mokkenpers accessoires
Veelgestelde vragen
Gebruiksinstructies
Systeeminstructies
Veligheidinstructies
2
FIRST TIME USE
Carefully remove all packing materials.
CHECK THE CONTENTS
Check if the box contains the following contents:
Mug Press
Power cord
Manual
SAFETY INSTRUCTIONS
When you change an accessory, make sure that the
power is switched off.
Make sure that the Voltage is 220V and applicable for
your use.
Do not let the press be switched on when it’s not in
use.
Be aware of the symbols used below:
Only allow qualied personnel to work with the mug
press. Keep children away.
Attention: Hot Attention: High Voltage
Be aware that some elements get hot during the
process. You can recognize these elements by the
yellow marking.
3
Connect the power cord.
Minus button
Safety catch
Switch the press on.
Mode button
Highest-temperature light
Plus button
Set-temperature light
Start / stop button
Sublimation time light
All read-outs are in Celsius. For Fahrenheit see the table on
page 7.
The press will automatically heat up to the set-temperature.
When it has reached this temperature, the press will make
a beeping sound.
To start the sublimation process, press the start / stop
button once. First, the press will heat up to the highest-
temperature. When this has been reached, the press will
count down the set time.
When the press has counted down to zero and the process
has nished, the press will make a long beeping sound.
Press the start / stop button again and it will stop.
To unplug a press accessory, make sure the power is
switched off and the press is cooled down. Press the safety
catch on the right side of the plug to release it (Picture B).
To set the set-temperature (Picture A), press the mode
button once. Then, adjust it with the plus and minus button.
The maximum set-temperature is 180°C.
To set the highest-temperature, press the mode button
for the second time. Then, adjust it with the plus and
minus button. Usually, this is a few degrees above the set-
temperature. The maximum highest-temperature is 200°C.
To set the sublimation time, press the mode button for the
third time. Then, adjust it with the plus and minus button.
To conrm the temperatures and time, press the mode
button for the fourth time.
CONTROL UNIT SETTINGS
SYSTEM INSTRUCTIONS PICTURE A
PICTURE B
NOTE!
The set-temperature is always lower
than the highest-temperature. If you
want to increase the set-temperature,
you need to increase the highest-
temperature rst.
4
USING THE MUG PRESS
INSTRUCTIONS
Before you switch on the mug press, set the correct
diameter of the mug press by adjusting the central screw
(Picture C). The ‘correct diameter’ means that you can close
the press with light pressure.
For temperature and time settings, check the time
and temperature overview at www.technotape.com >
Downloads > Time & Temperature.
Place the sublimation paper with the printed side of the
sublimation paper towards the product and adjust it with
special Technotape Heat Transfer Tape.
Close the press and push the start / stop button button.
It will take some time for the press to reach the highest-
temperature. Once it has been reached, the sublimation
process begins, and the press will count down the set time
automatically.
Once the sublimation time has nished, the press will make
a long beeping sound. Open the press and press the start
button to stop the sound.
When the press has reached the set-temperature, you can
place the product into the press.
Ceramic mug-like products (from 10oz mugs up to
beer mugs)
PICTURE C
PRODUCTION TIP!
For the best and sharpest result, dip
the mug into cold water immediately.
Remove the tape and sublimation paper directly after the
job has nished. But be careful because the mug is very hot.
5
ACCESSORIES
CHANGING ACCESSORIES
Release the safety catch (Picture E).
Unplug the cable.
Carefully remove the cable from the heating mat cable
clamp (Picture F).
Remove the heating mat from the holder and replace it by
another mat.
Carefully connect the cable to the heating mat cable clamp
and plug the cable into the control box.
Do not bend or fold the heating mats.
Before you change any accessory, make sure the
power is switched off and the press is cooled down.
There are different accessories available for the mug press:
Itemcode
Description
HPM.MUG.350.S16
For 8oz and smaller mugs
available separately
Heating Mat
Ø7,0 - 8,0 cm
Itemcode
Description
TRP.SRA.MUG.001
238 x 98 mm
250 sheets
Subpreme Mug Paper
110 gr/m²
Itemcode
Description
10 mm x 66 m
20 mm x 66 m also available
Tape
Heat Resistant
HTT.010.066.201
Safety catch
PICTURE E
Cable clamp 1
Cable clamp 2
PICTURE F
Itemcode
Description
HPM.MUG.350.S15
For 10oz and bigger mugs
Standard installed
Heating Mat
Ø7,5 - 9,5 cm
MUGPRESS ACCESSORIES
6
First, lengthen the sublimation time. If that doesn’t work,
raise the temperature with 3°C. The last option is to give the
press more pressure.
Reduce the sublimation time with 10 seconds.
Reduce the pressure or reduce the temperature.
The temperature is either too high or the sublimation paper
is of poor quality.
Reduce the sublimation time with 20 seconds.
The sublimation paper did not make contact with the
product completely. Usually this means that the surface of
the product is not completely smooth.
F.A.Q.
The transferred image is a little too light.
The transferred image is a little too vague.
The transferred image is not brilliant.
The paper is sticky.
The edges of the mug color brown.
The transferred image is partial vague.
PRODUCTION TIPS!
For the best result of ceramic products, dip
the product immediately into cold water after
sublimating.
To release the Technotape Heat Transfer Tape easily,
double fold one end of the tape.
Use very clean products only to prevent dust to
obstruct clear transfer.
Itemcode
SPM.082.096.002
Sublimation Mug 11oz White
Dishwasher & Microwave Safe
7
FAHRENHEIT - CELSIUS CONVERSION
8
EERSTE GEBRUIK
Verwijder voorzichtig het verpakkingsmateriaal.
CONTROLEER DE INHOUD
Controleer of de doos de volgende inhoud heeft:
Mokkenpers
Netspanningsnoer
Handleiding
VEILIGHEIDINSTRUCTIES
Als je een accessoire wil verwisselen, controleer dan
eerst of de stroom is uitgeschakeld.
Controleer of de voltage 220 Volt is en geschikt voor
gebruik.
Laat de pers niet aan staan als het niet in gebruik is.
Zo voorkom je oververhitting.
Wees alert op de volgende symbolen:
Laat alleen gekwaliceerde medewerkers met deze
pers werken. Houd kinderen uit de buurt.
Attentie: Heet Attentie: Spanning
Een aantal elementen van de pers wordt heet
tijdens gebruik. Wees hier alert op. Je herkent deze
elementen aan de gele markering.
Table des matières
Langues :
Autres manuels Technotape Outils électriques
