Technisonic Industries Limited TDFM-600 Manuel utilisateur

MULTIBAND P25

AIRBORNE TRANSCEIVER

MODEL TDFM-600/6000

Installation and

Operating Instructions

Til Document No.

01RE293

Rev. F

Issue 3

December 2004

Technisonic Industries Limited

240 Traders Blvd, Mississauga, Ontario L4Z 1W7

Tel:(905)890-2113 Fax:(905)890-5338

www.til.ca

CAUTION

This unit contains static sensitive devices. Wear a grounded wrist strap and/or conductive gloves when handling

printed circuit boards.

WARNING: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

device may not cause harmful interference and (2) this device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Warning:

Changes or modifications not expressly approved by Technisonic Industries could void

the users authority to operate the equipment.

WARRANTY INFORMATION

The Model TDFM-600/6000 Transceiver is under warranty for one year from date of purchase. Failed units caused by

defective parts, or workmanship should be returned to:

Technisonic Industries Limited Technisonic Industries Limited

240 Traders Boulevard 3840 E. Robinson Road, Suite 214

Mississauga, Amherst,

Ontario L4Z 1W7 New York 14228

Tel: (905) 890-2113 Fax: (905) 890-5338 Tel: (716) 691-0669

WARNING For compliance with FCC RF Exposure Requirements, the mobile

transmitter antenna installation shall comply with the following two

conditions:

1. The transmitter antenna gain shall not exceed 3 dBi

2. The transmitter antenna is required to be located outside of a vehicle and kept at a separation

distance of 70 cm or more between the transmitter antenna of this device and persons during

operation.

Summaryof DO-160CEnvironmentalTestingfor Technisonic ModelTDFM-600 and 6000Transceiver.

Conditions

Section

Description of Conducted Tests

Temperature and Altitude

4.0

Equipment tested to categories C4

and D1.

Vibration

8.0

Equipment is tested without shock

mounts to categories B, M and N.

Magnetic Effect

15.0

Equipment is class Z.

Power Input

16.0

Equipment tested to category B.

Voltage Spike

17.0

Equipment tested to category B.

RF Emission

21.0

Equipment tested to category Z.

Installation Approval Note

Presently no TSO standard exists for airborne FM transceivers. To make it easier for installation agencies to provide

their customers with an approved installation supported by an effective Airworthiness Approval, Technisonic has

secured Supplemental Type Certificate (STC) Approvals (both US and Canadian) on its Airborne FM products for many

helicopters currently being delivered in the US and Canada as well as a number of single engine fixed wing aircraft. The

above referenced DO-160C test data is also on file and available from Technisonic to support approval requirements in

airframes for which Technisonic does not possess an STC.

Approved aircraft types are listed in the attachments to the formal STC documents. These STC's are the exclusive

property of Technisonic and require the written authority of Technisonic for their use. To assist Factory Authorized

Technisonic Dealers in the certification process, we have placed copies of our Canadian and US STC's on our web site

along with a letter of authorization for their use. These documents may be downloaded and used as support for the

technical submission to FAA or Transport Canada. Only factory authorized dealers/installers are permitted to download

and make use of these documents on behalf of their customers (end users) in support of regulatory agency approval.

Please refer to the Technisonic web site www.til.ca for the latest issue of available STC=s and letter of authorization for

use.

TABLE OF CONTENTS

Paragraph Title Page

SECTION 1 GENERAL DESCRIPTION

1.1 Introduction............................................................................................... 1-1

1.2 Description ................................................................................................ 1-1

1.3 Model Variation.......................................................................................... 1-1

1.4 Technical Summary..................................................................................... 1-3

SECTION 2 OPERATING INSTRUCTIONS

2.1 General ..................................................................................................... 2-1

2.2 Front Panel................................................................................................ 2-1

2.3 Power Switch ............................................................................................ 2-2

2.4 Knob......................................................................................................... 2-2

2.5 Soft Keys and HOME .................................................................................. 2-3

2.6 Function Keys............................................................................................ 2-3

2.7 MUP and MDN Keys ................................................................................... 2-5

2.8 Up and Down Arrow Keys ........................................................................... 2-5

2.9 Left and Right Arrow Keys........................................................................... 2-5

2.10 ESW Key................................................................................................... 2-5

2.11 TSW Key................................................................................................... 2-5

2.12 Display...................................................................................................... 2-6

2.13 General Operation....................................................................................... 2-6

2.14 Customer Programming Software (CPS)......................................................... 2-6

2.15 Configuration Menu .................................................................................... 2-8

2.16 Flash Upgrade Mode ................................................................................... 2-9

2.17 Front Panel Programming (FPP) Mode............................................................ 2-9

SECTION 3 INSTALLATION INSTRUCTIONS

3.1 General ..................................................................................................... 3-1

3.2 Equipment Packing Log ............................................................................... 3-1

3.3 Transceiver Installation................................................................................ 3-1

3.4 Installation Kit -Contents ............................................................................ 3-1

3.5 Pin Locations and Connections..................................................................... 3-2

3.6 Wiring Instructions...................................................................................... 3-3

3.18 Post Installation Tests................................................................................. 3-7

LIST OF TABLES

Table No. Title Page

3-125-pin D Connections.................................................................................. 3-2

LIST OF ILLUSTRATIONS

Figure No. Title Page

2-1Operator’s Controls –TDFM-600/6000 ......................................................... 2-1

2-2Operator’s Controls –TDFM-636.................................................................. 2-2

3-1Outline Drawing ......................................................................................... 3-1

3-2Wiring Connections and notes...................................................................... 3-5

SECTION 1

GENERAL DESCRIPTION

1.1 INTRODUCTION

This publication provides operating and installation information on the TDFM-600/6000 series airborne

transceiver with firmware version TR14 and above. The exact model number depends on which and how many

RF modules are installed.

1.2 DESCRIPTION

The TDFM-600/6000 series of transceivers are airborne multi-band radios capable of operation in conventional

analog and P25 digital FM systems, SmartNet/SMART ZONE and P25 9600 trunking systems. Type I RF

modules are available in VHF, UHFLO, UHFHI and 800 MHz bands. Type II RF modules support additional

optional features not available in type I modules and are also available in VHF, UHFLO, UHFHI and 700/800

MHz.

These optional additional features include P25 9600 trunking that may be combined with AES and/or DES-OFB

encryption with OTAR in any of the available modules. The factory will only produce radios with all modules of

the type I or type II configuration since different Motorola CPS programming software is required for each type

of module.

It may be possible to retrofit existing type I transceivers with one or more type II modules to support optional

features not available on type I modules. Contact Technisonic for details.

Irrespective of module type the bands are numbered 1, 4, 5 and 8 respectively. The front panel LED display

indicates whether type I or II modules are present upon radio start-up. The transceiver’s part number will also

indicate which type of modules it contains. Please see section 1.3 on Model Variation below for details.

The following are typical model examples:

TDFM-680 -One 800 MHz module

TDFM-655 -Two UHF high band modules

TDFM-688 -Two 800 MHz modules

TDFM-6148 -One VHF, UHF low and 800 MHz module

TDFM-6158 -One VHF, UHF high and 800 MHz module

Module numbers are always specified in ascending numerical order. ie/ TDFM-6814 is not available.

The one exception to this numbering scheme is the model TDFM-636 which is a VHF transceiver with two type

II VHF modules and a 10 watt RF amplifier for each module.

1.3 MODEL VARIATION

There are several variations of the Model TDFM-600/6000 Transceiver. Each variation offers different

features and performance based on the type of RF modules and options installed. Single Band Transceivers

are available with the following Model numbers: TDFM-610 (VHF), TDFM-640 (UHF Lo), TDFM-650 (UHF

Hi) and TDFM-680 (800).

TDFM-600 Model Variations with type I Modules

*TDFM-6X0, P/N 011210-1-6X0/PYYY/28 GREEN display and 28 Volt back lighting.

*TDFM-6X0, P/N 011210-1-6X0/PYYY/5 GREEN display and 5 Volt back lighting.

TDFM-6XX, P/N 011210-1-6XX/PYYY/28 GREEN display and 28 Volt back lighting.

TDFM-6XX, P/N 011210-1-6XX/PYYY/5 GREEN display and 5 Volt back lighting.

TDFM-6XX, P/N 011210-2-6XX/PYYY/28 RED display and 28 Volt back lighting.

TDFM-6XX, P/N 011210-2-6XX/PYYY/5 RED display and 5 Volt back lighting.

TDFM-6XXNV, P/N 011210-1-6XXNV/PYYY/28 GREEN NV display and 28 Volt back lighting

TDFM-6XXNV, P/N 011210-1-6XXNV/PYYY/5 GREEN NV display and 5 Volt back lighting.

TDFM-6000 Model Variations with type I Modules

TDFM-6XXX, P/N 011210-1-6XXX/PYYY/28 GREEN display and 28 Volt back lighting.

TDFM-6XXX, P/N 011210-1-6XXX/PYYY/5 GREEN display and 5 Volt back lighting.

TDFM-6XXX, P/N 011210-2-6XXX/PYYY/28 RED display and 28 Volt back lighting.

TDFM-6XXX, P/N 011210-2-6XXX/PYYY/5 RED display and 5 Volt back lighting.

TDFM-6XXXNV, P/N 011210-1-6XXXNV/PYYY/28 GREEN NV display and 28 Volt back lighting

TDFM-6XXXNV, P/N 011210-1-6XXXNV/PYYY/5 GREEN NV display and 5 Volt back lighting.

X is represented by: PYYY represents a 3-digit project number

1 for VHF (138-174MHz) module that identifies specific options that are

4 for UHF Lo (403-470MHz) module contained in the module. The Technisonic

5 for UHF Hi (450-512MHz) module sales department assigns project numbers

8 for 800 MHz (806-870) based on customer requirements. P100

Module numbers must always be and P200 series project numbers are used

specified in ascending order. in transceivers with type I modules

*Note: 0 used when only one module installed. .

TDFM-600 Model Variations with type II Modules

*TDFM-6X0, P/N 011210-3-6X0/PYYY/28 GREEN display and 28 Volt back lighting.

*TDFM-6X0, P/N 011210-3-6X0/PYYY/5 GREEN display and 5 Volt back lighting.

TDFM-6XX, P/N 011210-3-6XX/PYYY/28 GREEN display and 28 Volt back lighting.

TDFM-6XX, P/N 011210-3-6XX/PYYY/5 GREEN display and 5 Volt back lighting.

TDFM-6XX, P/N 011210-4-6XX/PYYY/28 RED display and 28 Volt back lighting.

TDFM-6XX, P/N 011210-4-6XX/PYYY/5 RED display and 5 Volt back lighting.

TDFM-6XXNV, P/N 011210-3-6XXNV/PYYY/28 GREEN NV display and 28 Volt back lighting

TDFM-6XXNV, P/N 011210-3-6XXNV/PYYY/5 GREEN NV display and 5 Volt back lighting.

TDFM-6000 Model Variations with type II Modules

TDFM-6XXX, P/N 011210-3-6XXX/PYYY/28 GREEN display and 28 Volt back lighting.

TDFM-6XXX, P/N 011210-3-6XXX/PYYY/5 GREEN display and 5 Volt back lighting.

TDFM-6XXX, P/N 011210-4-6XXX/PYYY/28 RED display and 28 Volt back lighting.

TDFM-6XXX, P/N 011210-4-6XXX/PYYY/5 RED display and 5 Volt back lighting.

TDFM-6XXXNV, P/N 011210-3-6XXXNV/PYYY/28 GREEN NV display and 28 Volt back lighting

TDFM-6XXXNV, P/N 011210-3-6XXXNV/PYYY/5 GREEN NV display and 5 Volt back lighting.

X is represented by: PYYY represents a 3-digit project number

1 for VHF (138-174MHz) module that identifies specific options that are

4 for UHF Lo (380-470MHz) module contained in the module. P300, P400

5 for UHF Hi (450-520MHz) module and P500 project numbers are used in

8 for 700/800 MHz (764-870) transceivers with type II modules.

Module numbers must always be

specified in ascending order.

*Note: 0 used when only one module installed.

TDFM-636 Model Variations with type II VHF Modules

TDFM-636, P/N 011210-5-636/PYYY/28 GREEN display and 28 Volt back lighting.

TDFM-636, P/N 011210-5-636/PYYY/5 GREEN display and 5 Volt back lighting.

TDFM-636, P/N 011210-6-636/PYYY/28 RED display and 28 Volt back lighting.

TDFM-636, P/N 011210-6-636/PYYY/5 RED display and 5 Volt back lighting.

TDFM-636NV, P/N 011210-5-636NV/PYYY/28 GREEN NV display and 28 Volt back lighting

TDFM-636NV, P/N 011210-5-636NV/PYYY/5 GREEN NV display and 5 Volt back lighting.

TDFM-636 Project Number Note:

PYY represents a 3-digit project number that identifies specific options that are contained in the module. All

TDFM-636 transceivers are shipped as P600 units unless a custom project number is requested. P600 defines

specific options in each VHF module. VHF Module 1 supports P25 Trunking, Smart Zone and SMART NET

trunking protocols. VHF Module 2 supports conventional (non-trunked) operation with FPP (front panel

programming) capability. Both modules support secure communications using AES/DES-OFB/DES/DES-XL

encryption formats and P25 OTAR. Custom project numbers can be assigned by the Technisonic sales

department to meet non-standard requirements.

All model variations are provided with 28 Volt back lighting unless a specific request is made for 5 Volt AC

operation. NV (Night Vision) compatible option is only available with green display.

1.4 TECHNICAL CHARACTERISTICS

Specification Characteristic

Model Designation: TDFM-600/6000

Physical Dimensions: Approx. 8" X 3" X 5.75"

Weight: 4.2 lbs. (1.9 kg)

Operating Temperature Range: -30°C to +60°C

Power Requirement:

Voltage: 28.0 Vdc, ±15%

Current: 350mA minimum / 5A maximum

Audio Output Power (including sidetone): 500 mW into 600 ohms

Microphone Inputs: Carbon or Equivalent

Panel Back Lighting:

Voltage: 28 VDC or 5VAC

(specified when ordered)

Current: 100mA max. @28VDC

400mA max. @5VAC

Type I Modules

RF Output Power: 1 or 5 Watts (VHF)

1 or 4 Watts (UHF)

1 or 3 Watts (800)

Frequency Range -VHF Module: 136 to 178 MHz

UHF LO Module: 403 to 470 MHz

UHF HI Module: 450 to 512 MHz

800 Module: 806 to 870 MHz

No. of channels per band: 255 pre-programmable channels

Transmitter section VHF UHF 800

FM Hum and noise in dB (wideband): -48 -45 -45

Frequency Stability in ppm: ±2.0 ±2.0 ±1.5

Audio Distortion (at 1000Hz): <2% <2% <2%

Modulation Limiting: Wide band ±5kHz

Narrow band ±2.5kHz

1.3 TECHNICAL CHARACTERISTICS (continued)

Receiver section VHF UHF 800

Sensitivity in uV:

*Digital 1% BER (12.5kHz) 0.35 0.35 0.45

*Digital 5% BER (12.5kHz) 0.25 0.25 0.25

**Analog with 12dB SINAD 0.25 0.25 0.25

Selectivity in dB:

25 kHz Channel -78 -78 -75

12.5 kHz Channel -67 -68 -63

Intermodulation (dB) * ** -78 -77 -74

Type II Modules

RF Output Power: 1 or 7 Watts (VHF)

1 or 5 Watts (UHF)

1 or 3 Watts (800)

1 or 10 Watts (TDFM-636)

Frequency Range -VHF Module: 136 to 178 MHz

UHF LO Module: 380 to 470 MHz

UHF HI Module: 450 to 520 MHz

700/800 Module: 764 to 870 MHz

No. of channels per band: 512 pre-programmable channels

240 channels (15 zones of 16 channels)

for modules with Front Panel Programming.

Transmitter section VHF UHF 800

FM Hum and noise in dB (wideband): -48 -45 -45

Audio Distortion: 1% 1.5% 1.5%

Frequency Stability (ppm): ±2.0 ±2.0 ±1.5

Modulation Limiting: Wide band ±5kHz

Narrow band ±2.5kHz

Receiver section VHF UHF 800

Sensitivity in uV:

*Digital 1% BER (12.5kHz) 0.25 0.25 0.40

*Digital 5% BER (12.5kHz) 0.25 0.25 0.25

**Analog with 12dB SINAD 0.25 0.25 0.25

Selectivity in dB:

25 kHz Channel -80 -78 -72

12.5 kHz Channel -63 -63 -63

Intermodulation * ** -78 -77 -75

*Measured in digital mode per TIA/EIA IS 102.CAAA under nominal conditions.

** Measured in analog mode per TIA/EIA 603 under nominal conditions.

2-1

SECTION 2

OPERATING INSTRUCTIONS

2.1 GENERAL

A 2 line display and a keypad and 2 or 3 rotary knobs provide the operator control of the 1, 2 or 3 RF modules

installed in the unit. The display is showing the activity of one RF module at a time, selected by pressing the

desired knob. If the second rotary encoder on a single band unit is depressed the display will indicate that a RF

module is not installed for the second band. The knobs have multiple functions including volume, channel,

display dimmer. The microphone, key line and headphone audio are separate for each of the two or three bands

therefore switching from band to band is performed at an audio panel such as the Technisonic A710 series.

This allows for separate and simultaneous operation on each of the bands just like having 2 or 3 separate

radios. If combined operation is desired, a Technisonic AMS-6000 audio mode selector may be used ahead of

the audio controller.

2.2 FRONT PANEL

Refer to the diagrams below:

Figure 2-1 Front panel Controls –TDFM-600/6000 Series Transceivers (not including TDFM-636)

Autres manuels pour TDFM-600

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Technisonic Industries Limited Émetteur-récepteur

Technisonic Industries Limited

Technisonic Industries Limited TFM-530 Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited TFM-138A Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited TDFM-600 Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited TDFM-9200 Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited TiL-91-DE/S Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited TDFM-136 Manuel

Technisonic Industries Limited

Technisonic Industries Limited TDFM-136 Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited ACCESS/A A710X Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited TMS-110 Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited TDFM-9100 Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited TiL-90-6R Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited TFM-30 Manuel

Technisonic Industries Limited

Technisonic Industries Limited TFM-403 Manuel

Technisonic Industries Limited

Technisonic Industries Limited TDAM-1000 Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited TFM-556 Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited TDFM-9300 Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited TFM-138 Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited TiL-91-DE Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited T3018 Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited TFM-138 Manuel

Technisonic Industries Limited

Technisonic Industries Limited TFM-30 Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited TDFM-136 Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited TDFM-136A Manuel utilisateur

Technisonic Industries Limited

Technisonic Industries Limited TDFM-6000 Manuel utilisateur

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Kenwood

Kenwood ProTalk TK-3201 Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Kenwood

Kenwood TK-3180 Manuel d'utilisation et d'entretien

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Kenwood

Kenwood TK-2217 Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Kenwood

Kenwood TS-590SG Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur