TE Connectivity PRO-CRIMPER III Manuel utilisateur

Instruction Sheet

1 of 6

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

408-9252

25 JUN 19 Rev N

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and

low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

Product Family

Wire

Insulation

Color

Size

(AWG)

Maximum Insulation

Diameter (mm [in.])

Strip Length

Range (mm [in.])

PIDG* Terminal

PLASTI-GRIP* Terminal

Red

22-16

3.56 [.140]

5.15-5.95 [.203-.234]

Blue

16-14

4.32 [.170]

5.15-5.95 [.203-.234]

Yellow

12-10

6.35 [.250]

7.94-8.73 [.312-.344]

PIDG FASTON*

Terminal

Red

22-18

3.56 [.140]

8.33-9.14 [.328-.360]

Blue

16-14

4.32 [.170]

8.33-9.14 [.328-.360]

NOTE: Refer to Catalogs 82004 and 82042 for terminal selection information.

Figure 1

INTRODUCTION

PRO-CRIMPER III Hand Crimping Tool Assembly 58433-3 consists of PRO-CRIMPER III Hand Crimping Tool

Frame 354940-1 and Die Assembly 58423-1. The tool assembly is used to crimp the terminals listed in Figure

1. For additional information on the hand tool frame, refer to Instruction Sheet 408-9930.

Read these instructions thoroughly before using the tool assembly.

PRO-CRIMPER* III Hand Crimping

Tool Assembly 58433-3 with Die

Assembly 58423-1

Jaw

Pivot Pin

Die

Assembly

Back of Tool

(Wire Side)

Moving Jaw

PRO-CRIMPER III Hand

Crimping Tool Frame

354940-1 (408-9930)

Ratchet Adjustment Wheel

Handle

Moving

Handle

The PRO-CRIMPER III Hand Crimping Tool is a “Commercial" grade tool

and is designed primarily for field installation, repair, maintenance work,

or prototyping in industrial, commercial, or institutional applications.

Product crimped with this tool will meet the crimp height requirement for

hand tools in the appropriate Application Specification (114 Series) but

may not comply with other feature parameters of the specification. TE

Connectivity offers a variety of tools to satisfy your performance

requirements. For additional information, contact PRODUCT

INFORMATION at 1-800-522-6752.

408-9252

Rev N

2 of 6

Reasons for reissue of this instruction sheet are provided in Section 9, REVISION SUMMARY.

NOTE

All dimensions on this instructionsheet are in millimeters

[with inches in

brackets]. Figures arenot drawn to scale.

CAUTION

Terminals crimped with Tool 58433-3 or with Die Assembly 58423-1 are not Listed by Underwriters Laboratories Inc. (UL) or

CSA International.

DESCRIPTION

The tool frame features a stationary jaw and handle, a moving jaw and handle, and an adjustable ratchet that

ensures full crimping. The tool frame holds the die assembly. See Figure 1.

The die assembly consists of an anvil and indenter. When closed, the dies form three crimping chambers. The

indenter is marked with the letters R, B, and Y which correspond with the color of the terminal insulation (red,

blue, or yellow). Die retaining screws are used to secure the dies in the tool frame. See Figure 2.

Figure 2

INSTALLATION AND REMOVAL OF DIE ASSEMBLY

1. Close the tool handles until the ratchet releases, then allow the handles to open fully.

NOTE

The ratchet has detents that create audible clicks as the tool handles are closed.

2. Remove the two die retaining screws and die retaining pins (pins will not be used for this die

assembly) from the tool jaws.

3. Place the anvil in the moving jaw so that the marked surface faces outward. Insert the die retaining

screw through the hole of the moving jaw and hole of the anvil and tighten the screw just enough to

hold the anvil in place. DO NOT completely tighten the screw.

4. Place the indenter in the stationary jaw so that the marked surface faces outward. Insert the die

retaining screw through the hole of the stationary jaw and hole of the indenter and tighten the screw

just enough to hold the indenter in place. DO NOT completely tighten the screw.

5. Carefully close the tool handles, making sure the anvil and indenter align properly. Continue closing

the tool handles until the ratchet engages sufficiently to hold the anvil and indenter in place, then

tighten both die retaining screws.

6. To disassemble, close the tool handles until the ratchet releases, remove the two die retaining screws,

then slide the dies out of the tool jaws.

408-9252

Rev N

3 of 6

CRIMPING PROCEDURE [REFERENCE FIGURE 3]

NOTE

This tool is provided with a crimp adjustment feature. Initially, the crimp height of a sample terminal should be verified in

accordance with Section 5.

1. Refer to Figure 1 and select wire of the specified size and insulation diameter.

Strip the wire to the length indicated in Figure 1, taking care not to nick or cut wire strands.

2. Hold the tool so that the back (wire side) is facing you. Squeeze tool handles together and allow them

to open fully.

Figure 3

3. Place the terminal in the proper crimping chamber (match color code to terminal insulation) so the

edge of the insulation aligns with the edge of the indenter. Note: The wire barrel should be at the back

of the tool.

4. Hold the terminal in position, and squeeze the tool handles together until ratchet engages sufficiently

to hold the terminal. DO NOT deform the wire barrel.

5. Insert the stripped wire into the wire barrel and holding the wire in place, squeeze the tool handles

together until the ratchet releases.

Allow the tool handles to open and remove the crimped terminal.

6. Inspect the terminal crimp height according to Section 5.

CRIMP HEIGHT INSPECTION

This inspection requires the use of calipers. A lead rod can be used to check the crimp height. Crimp a rod in

each of the crimping chambers. Check the crimp height of the rod against the crimp height dimension given in

Figure 4.

Lead Rod Diameter

Crimping Chamber Marking

Crimp Height Dimension

4.8 [.19]

Y (Yellow)

3.35 ±0.15 [.132 ±.006]

3.2 [.12]

B (Blue)

2.44 ±0.15 [.096 ±.006]

3.2 [.12]

R (Red)

2.08 ±0.15 [.082 ±.006]

Figure 4

If the crimp height conforms to the dimension, the tool and die assembly are considered dimensionally correct.

Lubricate the tool with a thin coat of any good SAE 20 motor oil. If it does not, adjust the crimp height according

to Section 6. If the adjustment does not result in an acceptable crimp height, the die assembly or tool may have

to be replaced.

408-9252

Rev N

4 of 6

RATCHET ADJUSTMENT [FIGURE 5]

The tool ratchet mechanism features an adjustment wheel with numbered settings. The adjustment wheel

controls the amount of handle pressure exerted on the jaws during crimping. Check the crimp height according

to Section 5. If the crimp height is not acceptable, adjust the crimp height as follows:

1. Remove the lockscrew from the ratchet adjustment wheel.

2. With a screwdriver, adjust the ratchet wheel from the front of the tool.

3. Observe the ratchet adjustment wheel.

If a tighter (smaller) crimp height is required, rotate the adjustment wheel counterclockwise to a

higher-numbered setting.

If a looser (larger) crimp height is required, rotate the adjustment wheel clockwise to a lower-

numbered setting.

4. Re-assemble the lockscrew.

5. Make a sample crimp.

If the crimp height is acceptable, the adjustment setting is correct. If the crimp height is unacceptable,

continue to adjust the ratchet, and again measure a sample crimp.

Figure 5

MAINTENANCE AND INSPECTION

7.1. Maintenance

Ensure that the tool frame and dies are clean by wiping them with a clean, soft cloth. Remove any debris with a

clean, soft brush. Do not use objects that could damage any components. When not in use, keep tool handles

closed to prevent objects from becoming lodged in the dies, and store in a clean, dry area.

7.2. Visual Inspection

Inspection of the dies should be made on a regular basis to ensure that they have not become worn or

damaged. Inspect the crimping chambers for flattened, chipped, worn, or broken areas. If damage or abnormal

wear is evident, the dies must be replaced. Refer to Section 8, REPLACEMENT and REPAIR.

408-9252

Rev N

5 of 6

REPLACEMENT AND REPAIR

Customer-replaceable parts are listed in Figure 1. Available separately, Repair Kit 679221-1 includes a

replacement lock nut and a variety of pins, rings, screws, and springs. If the dies are damaged or worn

excessively, they must be replaced. Parts other than those listed should be replaced by TE Connectivity to

ensure quality and reliability. For customer repair service or to order replacement parts, call 1-800-522-6752, or

fax your purchase order to 717-986-7605, or write to:

CUSTOMER SERVICE (038-035)

TE CONNECTIVITY CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

REVISION SUMMARY

Revisions to this instruction sheet include:

Revised with most up-to-date corporate logo, entity designation and outline structure.

Eliminated redundant Section 6 and included relevant parts in Section 5

Moved locations of Figure 3 and 4 and added Figure 6 designation

Revised many part numbers in Figure 6 and designated Micro SDE tool 2280380-[ ] as not

recommended.

408-9252

Rev N

6 of 6

Figure 6

PRO-CRIMPER III Hand Tool Frame 354940-1

(Instruction Sheet 408-9930)

SDE-SA Hand Tool 9-1478240-0

(Instruction Sheet 408-8851)

SDE Bench Terminator 539630-2, with Adaptor 1673663-2

(Customer Manual 412-94328)

626 Adaptor 679304-1

(Instruction Sheet 408-4070)

Battery Tool (Shouldered Die) 2217480-1 and -2

(Customer Manual 409-32031)

Battery Tool (Pin Die) 2217481-1 and -2

(Customer Manual 409-32032)

Micro SDE (Standard Die Envelope) Lithium Ion

Battery Powered Crimp Tool Kits 2280380-[ ]

Autres manuels pour PRO-CRIMPER III

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TE Connectivity Outils électriques

TE Connectivity

TE Connectivity 2395361-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2363592-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2390881-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2381460-1 Manuel utilisateur

TE Connectivity

TE Connectivity PRO- CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity 2155369 Manuel utilisateur

TE Connectivity

TE Connectivity HT40 Manuel utilisateur

TE Connectivity

TE Connectivity 2844990-1 Guide de référence

TE Connectivity

TE Connectivity 2393336-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2381114-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2063523-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2430768-1 Manuel utilisateur

TE Connectivity

TE Connectivity 1976330-1 Manuel utilisateur

TE Connectivity

TE Connectivity MATE-AX 2335290-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2390076-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2389862-1 Manuel utilisateur

TE Connectivity

TE Connectivity NanoMQS 2280687-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2393337-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2390276-1 Manuel utilisateur

TE Connectivity

TE Connectivity 1976330-1 Manuel utilisateur

TE Connectivity

TE Connectivity 46447 Manuel utilisateur

TE Connectivity

TE Connectivity 91904 Series Manuel utilisateur

TE Connectivity

TE Connectivity 2031676-1 Manuel utilisateur

TE Connectivity

TE Connectivity 1901343 Series Guide de référence

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel