TA Instruments Q1000 Manuel utilisateur

This procedure will cover the steps to properly pack up the Q1000/Q2000 DSC for

shipment.

Packing Materials Provided:

Cell shipping foam w/ clamp

Shipping plug

Autolid shipping foam

2 Rubber bands

4 Shipping hooks

Tools Required:

Phillips screwdriver

Flathead screwdriver

3/32” or 5/32” (depending on cooling device)

Heavy-duty tape

Strapping kit

NOTE: If this instrument is equipped with an RCS or LNCS, the flange temperature

must be at ambient temp before removing the cooling head.

1. Remove any samples from the cell area. Remove the dust cover and the sample

tray (if applicable).

2. Remove the waste bin and insert the shipping plug (Figure 1).

3. For Q1000:

a. On the LCD screen, press the “Control Menu” button.

b. Press the “Autolid” button so the lid will open.

For Q2000:

a. On the LCD screen, press the “CONTROL” button

b. Press the lid icon on the left hand side of the screen.

c. The control command should say “LID OPEN”.

d. Press “APPLY “button so the lid will open.

4. Remove the 4 screws that hold on the blue cell dress cover and remove the cover.

Page 1 of 1

5. Unplug the 2-pin heater power wire (RCS ONLY).

6. Remove the cooling unit (RCS, LNCS, FACS) from the cell (Figure 2).

7. Place the shipping foam over the cell (Figure 3). Tighten the shipping clamp.

8. Re-install the blue dress cover over the cell (Figure 4).

9. For Q1000:

a. On the LCD screen, press the “CONTROL MENU” button.

b. Next, press the “AUTOSAMPLER” button.

c. The autolid (over the cell) will automatically open (if not already). This is

normal.

d. Next, press the “TEST MODE” button and then the “SENSORS” button.

e. On this screen, you will see a button labeled “SHIP”. Pressing this button

will move the autosampler arm and insert the fingers into the shipping

plug (Figure 5).

f. Press the “EXIT” button until you are at the main menu.

g. Press the “AUTOLID” button to bring the lid down over the foam

covering the cell.

For Q2000:

a. On the LCD screen, press the “CALIB” button.

b. Press the autosampler icon.

c. Select the “MOTOR TEST” tab.

d. Press the “SHIP” button. Pressing this button will move the autosampler

arm and insert the fingers into the shipping plug (Figure 5).

e. Press the “CONTROL” button, to return to the control menu.

f. Press the lid icon on the left hand side of the screen.

e. The control command should say “LID CLOSE”.

g. Press “APPLY “button so the lid will close.

10. Now you will need to install the shipping foam between the autolid outer cover

and the arm (Figure 6).

11. Next, band down the autolid arm and autosampler arm using the rubber band and

hooks (Figures 7 & 8).

12. For Q1000:

a. Press the “Display Menu” button on the touch panel. Press the

“Shutdown” button.

For Q2000:

a. Press the “CONTROL” button on the touch panel.

b. Press the switch icon.

c. Scroll down to “SHUTDOWN”.

Page 2 of 2

13. Press the “APPLY” button. When the instrument says it okay to shutdown, turn

off the power switch on the back of the instrument.

14. Disconnect all cords, cables, and tubing to the instrument.

15. If shipping the instrument in the reusable TA plastic shipping container;

a. Place instrument in shipping container.

b. Place top portion of shipping container over the instrument. Note the

direction, the “FRONT” is labeled on both the top and bottom portions of

the container. Secure the latches on all of the sides.

c. Your instrument is now ready to ship.

16. If shipping the instrument in the cardboard shipping carton;

a. Carefully lift the instrument and remove the feet.

b. Place the instrument on the plastic pallet.

c. Secure instrument to pallet with 4 shipping bolts.

d. Place feet and accessories into accessory box and place box next to

instrument on pallet.

e. Place outside carton over pallet and seal with heavy-duty tape.

f. Using a strapping kit, secure outside carton to the plastic pallet.

g. Your instrument is now ready to ship.

TA Instruments strongly recommends using a Motor

Freight Carrier!

Page 3 of 3

Shipping plug

Figure 1

Figure 2

Page 4 of 4

Shipping Foam

Shipping clamp

Figure 3

Figure 4

Page 5 of 5

Autosampler Arm

Shipping Foam

Figure 5

Figure 6

Page 6 of 6

Rubberband

Shipping Hook

(One not shown)

Figure 7

Rubberband

Shipping Hooks

Figure 8

Page 7 of 7

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TA Instruments Instrument de mesure

TA Instruments

TA Instruments TGA5500 Manuel utilisateur

TA Instruments

TA Instruments Nano ITC Series Manuel utilisateur

TA Instruments

TA Instruments DHR Series Manuel utilisateur

TA Instruments

TA Instruments TMA 2940 Manuel utilisateur

TA Instruments

TA Instruments DISCOVERY XENON FLASH Manuel utilisateur

TA Instruments

TA Instruments ARES-G2 Manuel utilisateur

TA Instruments

TA Instruments DHR Series Manuel utilisateur

TA Instruments

TA Instruments TMA 2940 Manuel utilisateur

TA Instruments

TA Instruments AR 2000 Manuel utilisateur

TA Instruments

TA Instruments DSC Q Series Manuel utilisateur

TA Instruments

TA Instruments TMA 2940 CE Manuel utilisateur

TA Instruments

TA Instruments TMA Q400 Manuel utilisateur

TA Instruments

TA Instruments TGA 2950 Manuel utilisateur

TA Instruments

TA Instruments TGA 2050 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur