Synology FlashStation FS3600 Manuel
Hardware Installation Guide
Synology NAS FS3600
Table of Contents
Chapter 1: Before You Start
Package Contents 3
Synology FS3600 at a Glance 4
Hardware Specication 5
Optional Accessories 6
Safety Instructions 8
Chapter 2: Hardware Setup
Tools and Parts for Component Installation 9
Install Drives 9
Install Memory Modules 11
Install PCle Add-in Cards 13
Install and Remove Rail Kits 15
Expansion Unit Deployment and Topology 18
Start up Your Synology NAS 19
LED Indicator Table 20
Chapter 3: System Maintenance
Replace System Fan 21
Replace Power Supply Unit (PSU) 23
Initial Troubleshooting Guide 23
Chapter 4: Install DSM on Synology NAS
Install DSM with Web Assistant 24
Learn More 24
Synology_HIG_FS3600_20190812
2
Synology NAS FS3600 is an enterprise server consisting of both system hardware and the software operating
system, DiskStation Manager (DSM). This manual will guide you through all conguration aspects of your
FS3600, including the hardware components, setup procedures, system maintenance, and initial troubleshooting
instructions.
Note: All images below are for illustrative purposes only, and may dier from the actual product.
Package Contents
Main unit x 1 AC power cord x 2
Screws for 2.5” drives x 100
Before You Start 1
Chapter
3
3
4Chapter 1: Before You Start
Synology FS3600 at a Glance
81110
15 1614
13
12
9
17
No. Article Name Location Description
1 Power Button and Indicator
Front
1. Press to power on your FS3600.
2. To power o the FS3600, press and hold until you hear a beep sound
and the Power LED starts blinking.
2 Status Indicator Displays the status of the system. For more information, see "LED
Indicator Table".
3 Alert Indicator Displays warnings regarding fan or temperature. For more information,
see "LED Indicator Table".
4 Beep O Button Press to deactivate the beeping sound that is emitted when a malfunction
occurs.
5 Drive Status Indicator Displays the status of drives. For more information, see "LED Indicator
Table".
6 Drive Tray Install drives (hard disk drives or solid state drives) here.
7 Rail Kit Release Tab Push in and hold to release your FS3600 from the rail kit lock.1
8 Power Port
Back
Connect power cords here.
9 PSU Indicator and Beep O
Button
1. Displays the status of the power supply unit (PSU). For more
information, see "LED Indicator Table".
2. Press to deactivate the beeping sound that is emitted when a
malfunction occurs.
10 PSU Fan Disposes of excess heat and cools the PSU.
11 Console Port This port is reserved for manufacturing use only.
12 PCI Express Expansion Slot Supports one PCIe x8 add-on network interface card.
13 SAS OUT Port Connect Synology Expansion Unit to the SAS OUT port on the right side.2
14 1GbE LAN Port Connect RJ-45 network cables here.
15 10GBase-T LAN Port Connect RJ-45 network cables here.
16 USB 3.0 Port Connect external drives, USB printers, or other USB devices to your
FS3600 here.
17 RESET Button
1. Press and hold until you hear a beep sound to restore the default IP
address, DNS server, and password for the admin account.
2. Press and hold until you hear a beep sound, then press and hold
again until you hear three beep sounds to return the FS3600 to “Not
Installed” status so that DiskStation Manager (DSM) can be reinstalled.
1For more information about the rail kit installation, please refer to the Quick Installation Guide that comes with the rail kit.
2For more information about Synology Expansion Unit supported by your Synology NAS, please visit www.synology.com.
5Chapter 1: Before You Start
Hardware Specication
Item FS3600
Internal Drive 2.5" SAS drive (SSD and HDD) or SATA SSD x 24
Maximum Internal Raw
Capacity 92.16 TB (24 x 3.84 TB SSD)
External Device Port • USB 3.0 x 2
• SAS OUT x 1
LAN Port • 1GbE (RJ-45) x 4
• 10GBase-T (RJ-45) x 2
PCIe Slot Gen3 x8 slot (x8 link) x 1
Size (H x W x D) (mm) • 88 x 482 x 724 (with server ears)
• 88 x 430.5 x 692
Weight (kg) 14.9
Supported Client • Windows 7 onwards
•macOS 10.12 onwards
File System • Internal: Btrfs, ext4
• External: Btrfs, ext4, ext3, FAT32, NTFS, HFS+, exFAT1
Supported RAID Type • Basic • JBOD • RAID 0 • RAID 1
• RAID 5 • RAID 6 • RAID 10 • Synology RAID F1
Agency Certication • FCC Class A • CE Class A • BSMI Class A
• VCCI • EAC • RCM • RoHS Compliant
HDD Hibernation Yes
Scheduled Power On/O Yes
Wake on LAN Yes
Language Localization
Environment Requirement
• Line voltage: 100V to 240V AC
• Frequency: 50/60 Hz
•Operating Temperature: 32 to 95˚F (0 to 35˚C)
•Storage Temperature: -5 to 140˚F (-20 to 60˚C)
• Relative Humidity: 5% to 95%RH
Note: Model specications are subject to change without notice. Please refer to www.synology.com for the latest information.
1Support for exFAT can be enabled by purchasing and downloading exFAT Access in Package Center.
6Chapter 1: Before You Start
Optional Accessories
With Synology accessories, you can customize your Synology NAS to t dierent business environments without
worrying about compatibility and stability. Visit www.synology.com/compatibility for more information.
• Memory Module
Model Name Picture Description
D4RD-2666-16G 16GB DDR4-2666 ECC
Registered DIMM
D4RD-2666-32G 32GB DDR4-2666 ECC
Registered DIMM
Note: It is required to use D4RD-2666-16G with identical memory modules of the same capacity and frequency.
• PCIe Add-in Card
Model Name Picture Description
E10G18-T2 Dual-port, 10GbE RJ-45
Network Interface Card
E10G18-T1 Single-port, 10GbE RJ-45
Network Interface Card
E10G17-F2 Dual-port, 10GbE SFP+ Network
Interface Card
7Chapter 1: Before You Start
• Expansion Unit
Model Name Picture Description
RX1217sas
2U 12-bay Rackmount type
expansion unit, compatible with
3.5”/2.5” SAS/SATA drives
RX2417sas
2U 24-bay Rackmount type
expansion unit, compatible with
2.5” SAS/SATA drives
• Rail Kit
Model Name Picture Description
RKS1317 Sliding rail solutions
• Spare Part
Model Name Picture Description
Disk Tray (Type R1) 2.5" Drive Tray
FAN 80*80*32_6 System Fan Module
PSU 500W-RP
Module_2 Redundant PSU Module
PSU 500W-RP SET_2 Redundant PSU Set (Cage x 1, PSU
Module x 2)
8Chapter 1: Before You Start
Safety Instructions
Keep away from direct sunlight and away from chemicals. Make sure the environment does not
experience abrupt changes in temperature or humidity.
Place the product right side up at all times.
Do not place near any liquids.
Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or
aerosol cleaners.
To prevent the unit from falling over, do not place on carts or any unstable surfaces.
The power cord must plug in to the correct supply voltage. Make sure that the supplied AC voltage is
correct and stable.
To remove all electrical current from the device, ensure that all power cords are disconnected from
the power source.
Risk of explosion if battery is replaced with an incorrect type. Dispose of used batteries appropriately.
Tools and Parts for Component Installation
Please prepare the tools and parts below before setting up your Synology NAS:
• A screwdriver
• At least one 2.5” SSD (SAS/SATA) or HDD (SAS only) (please visit www.synology.com/compatibility for
compatible drive models).
Warning: If you install a drive that contains data, the system will format the drive and erase all existing data. Please
back up any important data before installation.
• Rail mounting kit (please see the Optional Accessories section to nd out the suitable rail kit for cabinet
installation)
Warning: We suggest mounting your Synology NAS on a cabinet before installing any drives since the heavy weight
will increase the installation diculty.
Install Drives
Please follow the steps below for drive installation:
1 Open the drive tray.
a Find the small button located on the bottom side of the drive tray handle. Press the button down, and the
drive tray handle will pop out.
b Pull the drive tray handle out as illustrated above.
2 Place the drive in the drive tray. Tighten screws into the four spots indicated below to secure the drive.
Hardware Setup
9
2
Chapter
10 Chapter 2: Hardware Setup
3 Insert the loaded drive tray into the empty drive bay.
Note: Make sure the tray is pushed in all the way. Otherwise, the drive might not be able to function properly.
4 Push the handle inward to secure the drive tray.
5 Push the switch on the drive tray handle to the bottom to lock the drive tray.
6 Repeat the steps above to assemble the other drives you have prepared.
7 Drives are numbered as shown below.
Note: We suggest installing drives of the same size to optimize drive capacity usage when creating RAID volumes.
Table des matières
Autres manuels Synology Stockage
Synology
Synology RackStation RS2414RP+ Manuel utilisateur
Synology
Synology DiskStation Series Manuel utilisateur
Synology
Synology DiskStation DS1517+ Manuel
Synology
Synology SA3610 Manuel utilisateur
Synology
Synology DS1813+ Manuel utilisateur
Synology
Synology DX513 Manuel utilisateur
Synology
Synology DiskStation DS418 16TB-IW Manuel
Synology
Synology DiskStation DS716+II Manuel utilisateur
Synology
Synology DS3617xsII Manuel
Synology
Synology DiskStation DS214se Manuel utilisateur
Synology
Synology DX513 Manuel utilisateur
Synology
Synology NAS DS220+ Manuel
Synology
Synology DiskStation DS110+ Manuel utilisateur
Synology
Synology DiskStation DS920+ Manuel
Synology
Synology DS-106 Series Manuel utilisateur
Synology
Synology DX513 Manuel utilisateur
Synology
Synology DiskStation DS3612xs Manuel utilisateur
Synology
Synology DiskStation DS216se Manuel utilisateur
Synology
Synology DiskStation DS3018xs Manuel
Synology
Synology RS2423+ Manuel utilisateur
Manuels Stockage populaires d'autres marques
Spectra Logic
Spectra Logic T-Series Spectra T50e Manuel utilisateur
Panasonic
Panasonic LKM-F931-1 Manuel utilisateur
Tabernus
Tabernus Enterprise Erase E2400 Manuel utilisateur
Rocstor
Rocstor COMMANDER 3F series Manuel utilisateur
HP
HP P9000 Manuel utilisateur
Western Digital
Western Digital Ultrastar Data60 Manuel utilisateur