Synology NAS DS2419+II Manuel

Synology NAS DS2419+II

Hardware Installation Guide

Table of Contents

Chapter 1: Before You Start

Package Contents

Synology NAS at a Glance

Safety Instructions

Chapter 2: Hardware Setup

Tools and Parts for Drive Installation

Install Drives

Start Up Your Synology NAS

Add a RAM Module on Synology NAS

Add a Network Interface Card

Replace System Fan

Chapter 3: Install DSM on Synology NAS

Install DSM with Web Assistant

Learn More

Appendix A: Specications

Appendix B: LED Indicator Table

Synology_HIG_DS2419+II_20210315

Thank you for purchasing this Synology product! Before setting up your new Synology NAS, please check the

package contents to verify that you have received the items below. Also, make sure to read the safety instructions

carefully to avoid harming yourself or damaging your Synology NAS.

Package Contents

Main unit x 1 AC power cord x 1

RJ-45 LAN cable x 2

Screws for 2.5" drives x 52

Drive tray key x 2

Before You Start 1

Chapter

4Chapter 1: Before You Start

Synology NAS at a Glance

1 2 3 4

No. Article Name Location Description

1Status Indicator

Front Panel

Displays the status of the system. For more information, see "Appendix B:

LED Indicator Table".

2Alert Indicator Displays warnings regarding fan or temperature. For more information, see

"Appendix B: LED Indicator Table".

3Power Button

1. Press to power on the Synology NAS.

2. To power o󰀨 the Synology NAS, press and hold until you hear a beep

sound and the Power LED starts blinking.

4LAN Indicator Displays the status of the network connection. For more information, see

"Appendix B: LED Indicator Table".

5Drive Status Indicator Displays the status of the installed drive. For more information, see "Appendix

B: LED Indicator Table".

6Drive Tray Install drives (hard disk drives or solid state drives) here.

7Drive Tray Lock Lock or unlock drive trays.

8Power Port

Back Panel

Connect the AC power cord here.

9Fan Disposes of excess heat and cools the system. If the fan malfunctions, the

Synology NAS will emit a beeping sound.

10 PCI Express

Expansion Slot Supports one PCIe x8 slot (x4 link) add-on card.

11 USB 3.0 Port Connect external drives or other USB devices to the Synology NAS here.

12 RESET Button

1. Press and hold until you hear a beep sound to restore the default IP

address, DNS server, and password for the admin account.

2. Press and hold until you hear a beep sound, then press and hold again

until you hear three beep sounds to return the Synology NAS to “Not

Installed” status so that DiskStation Manager (DSM) can be reinstalled.

13 Console Port This port is used for manufacturing use only.

14 Expansion Port Connect Synology Expansion Unit1to the Synology NAS here.

15 LAN Port Connect network cables here.

1For more information about Synology Expansion Unit supported by your Synology NAS, please visit www.synology.com.

5Chapter 1: Before You Start

Safety Instructions

Keep away from direct sunlight and away from chemicals. Make sure the environment does not

experience abrupt changes in temperature or humidity.

Place the product right side up at all times.

Do not place near any liquids.

Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or

aerosol cleaners.

To prevent the unit from falling over, do not place on carts or any unstable surfaces.

The power cord must plug in to the correct supply voltage. Make sure that the supplied AC voltage is

correct and stable.

To remove all electrical current from the device, ensure that all power cords are disconnected from

the power source.

Risk of explosion if battery is replaced with an incorrect type. Dispose of used batteries appropriately.

Tools and Parts for Drive Installation

• A screwdriver (only for 2.5"drives)

• At least one 3.5"or 2.5"SATA drive (please visit www.synology.com for compatible drive models.)

Warning: If you install a drive that contains data, the system will format the drive and erase all existing data. Please

back up any important data before installation.

Install Drives

1 Press the right part of the drive tray to pop out the handle.

2 Pull the drive tray handle in the direction as indicated below to remove the drive tray.

Hardware Setup

Chapter

7Chapter 2: Hardware Setup

3 Load drives in the drive trays.

• For 3.5" drives: Remove the fastening panels from the sides of the drive tray. Place the drive in the drive

tray. Then insert the fastening panels to secure the drive in place.

• For 2.5" drives: Remove the fastening panels from the sides of the drive tray and store them in a safe

place. Place the drive in the blue area (shown below) of the drive tray. Turn the tray upside down and tighten

the screws to secure the drive in place.

4 Insert the loaded drive tray into the empty drive bay.

Note: Make sure the tray is pushed in all the way. Otherwise, the drive might not be able to function properly.

5 Press the handle in ush with the front panel to hold the drive tray in place.

8Chapter 2: Hardware Setup

6 Insert the drive tray key into the drive tray lock, turn the key clockwise (to the “-” position) to lock the handle of

the drive tray, and then remove the key.

7 Repeat the steps above to assemble the other drives you have prepared.

8 Drives are numbered as shown below.

Note: If you want to create a RAID volume, we recommended that all installed drives are of the same size to make

the best use of drive capacity.

9Chapter 2: Hardware Setup

Start Up Your Synology NAS

1 Use the LAN cable to connect the Synology NAS to your switch, router or hub.

2 Connect one end of the AC power cord to the power port of the Synology NAS, and the other to the power

outlet.

3 Press the power button.

Congratulations! Your Synology NAS is now online and detectable from a network computer.

10 Chapter 2: Hardware Setup

Add a RAM Module on Synology NAS

The optional Synology DDR4 RAM module is designed for Synology NAS memory expansion. Follow the steps

below to install, check, or remove a RAM module on your Synology NAS.

To install the RAM module:

1 Press and hold the power button until you hear a beep sound to shut down your Synology NAS. Disconnect all

cables from your Synology NAS to prevent any possible damage.

2 Remove the side panel:

a Remove the 2 screws on the back of Synology NAS.

b Pull the side panel. Place the side panel to the side.

Note: When you remove the case, you expose sensitive internal components. Avoid touching anything other than the

memory assembly when you remove or add memory.

Table des matières

Autres manuels Synology Serveur

Synology

Synology DS101 Series Manuel utilisateur

Synology

Synology 406 Series Manuel utilisateur

Synology

Synology NAS SA3600 Manuel

Synology

Synology RackStatio RS3411xs Manuel utilisateur

Synology

Synology NAS RS3621xs+ Manuel

Synology

Synology RackStation RS1219+ Manuel

Synology

Synology DS723+ Manuel utilisateur

Synology

Synology NAS RS1221RP+ Manuel

Synology

Synology RackStation RS3614xs Manuel utilisateur

Synology

Synology NAS HD6500 Manuel

Synology

Synology RX410 Manuel utilisateur

Synology

Synology RackStation RS2818RP+ Manuel

Synology

Synology DiskStation DS410j Manuel utilisateur

Synology

Synology DS108j Manuel utilisateur

Synology

Synology NAS FS3400 Manuel

Synology

Synology NAS RS2421+ Manuel

Synology

Synology RX6022sas Manuel

Synology

Synology RackStation RS3614xs+ Manuel utilisateur

Synology

Synology RX1222sas Manuel

Synology

Synology DS207 Series Manuel utilisateur

Synology

Synology CS-406 Manuel utilisateur

Synology

Synology NAS FS3410 Manuel

Synology

Synology RackStation RS3618xs Manuel

Synology

Synology FX2421 Manuel

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur