Symmetry EN-7530 Manuel utilisateur
Symmetry EN-7530
Installation Guide
INFORMATION TO USER
CAUTION
RISK OF ELECTRIC SHOCK,
DO NOT OPEN
!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of un-insulated
“dangerous voltage” within the product‟s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
!
This symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
Symmetry EN-7500 Series EN-7530 Installation Guide
9600-0545 Issue 1.1 Page 3 of 21
Table of Contents
1. FEATURES........................................................................................................ 4
2. PACKAGE CONTENTS.................................................................................... 5
3. PART NAMES.................................................................................................... 6
3.1.Internal View..................................................................................................................... 6
4. INSTALLATION................................................................................................. 7
4.1. Installation Template...................................................................................................... 8
4.2. Manual adjustment for 3-axis movements.................................................................. 9
4.3. Setting the Image Attribute............................................................................................ 9
4.4. Operating the OSD Menu.............................................................................................. 9
5. CONNECTIONS............................................................................................... 10
5.1.Connectors...................................................................................................................... 10
6. CONFIGURATION........................................................................................... 13
6.1.Set up network environment ........................................................................................ 13
6.2. View video on web page.............................................................................................. 13
6.2.1. View video using IPAdmin Tool........................................................................... 13
6.2.2.View video using IP address................................................................................. 16
6.3. Reset............................................................................................................................... 16
6.4. Factory Default.............................................................................................................. 16
APPENDIX A: SPECIFICATIONS ...................................................................... 17
Summary................................................................................................................................ 17
Electrical Characteristics..................................................................................................... 18
Environmental Condition..................................................................................................... 18
Analytics................................................................................................................................. 19
APPENDIX B: POWER OVER ETHERNET....................................................... 20
PoE compatibility.................................................................................................................. 20
Power classification.............................................................................................................. 20
APPENDIX C: DIMENSIONS.............................................................................. 21
Symmetry EN-7500 Series EN-7530 Installation Guide
9600-0545 Issue 1.1 Page 4 of 21
1. FEATURES
Camera
Indoor/Outdoor Fixed Dome IP Camera (Vandal Proof)
High Quality Compression in real time streaming
Sony 1/3” Super HAD CCD & High Quality SS-HQ1 Full Kit Chip Set
Sony 1/3" Vertical Double Density Color CCD (Optional)
True Day / Night (ICR)
Improvement of color rolling suppression
Streaming
Dual streaming mode (with different codec/resolution/bit rate etc.)
De-interlacing on DSP
Burnt-in text supported
Unicast/Multicast supported
Video/Audio
Video compression: H.264/MPEG/MJPEG, 25/30FPS@D1(PAL/NTSC)
Audio compression: G.711(µLaw, aLaw)/PCM
Analog video out for external monitors
Video Motion Detection supported
2-way mono audio supported
Network
RTSP/ HTTP protocol supported
10/100 Base-T Ethernet
Additional Features
RS-485 supported
Micro SD card supported
PoE supported
Built-in Video Analytics
OSD supported
Analytics
Intelligent Detection (Included as basic)
VCA (Optional)
Symmetry EN-7500 Series EN-7530 Installation Guide
9600-0545 Issue 1.1 Page 5 of 21
2. PACKAGE CONTENTS
Unpack carefully and handle the equipment with care. The packaging contains:
Camera
DC power adaptor
Extension cable
(for LAN and power connector)
11 Pin terminal block
Hex wrench driver
Screws and Anchor blocks
Installation Template
Video BNC Cable
Quick Installation Guide
Surface Cushion
(for protection against dust)
Note
i
The above contents are subject to change without prior notice.
Symmetry EN-7500 Series EN-7530 Installation Guide
9600-0545 Issue 1.1 Page 6 of 21
3. PART NAMES
3.1. Internal View
1. 11 pin terminal block for D/I, D/O, audio, and serial communication
11 pin terminal block for D/I, D/O, Audio In /Out and serial communication. Refer to the
section “5.1. Connectors”for further information.
2. Reset
Reset switch is used for restarting or resetting the camera to Factory Default (FD).
Refer to the section “6.3. Reset”for more specific information.
3. Micro SD Card Socket
Memory card slot for external storage.
4. Extension Cable Socket
Socket for LAN and power connector.
5. LAN Connector (Ethernet)
RJ45 LAN connector for 10/100 Base-T Ethernet. This socket can also be used to
power the camera via PoE (Optional).
6. Power Adaptor Connector (DC 12V)
The camera needs a DC 12V 1A adapter for power supply.
①
②
③
④
* Models herein and their
appearance are subject to change
without any prior notice.
⑥
⑤
Symmetry EN-7500 Series EN-7530 Installation Guide
9600-0545 Issue 1.1 Page 7 of 21
4. INSTALLATION
Note
i
When assembling the main body of the camera and its dome cover,
make sure they fit each other into place.
1) Connect the LAN cable, power
supply cable, and the video loop out
cable with the camera.
2) Place the installation template on
the ceiling.
3) Drill three holes on the template
and insert anchor blocks into the
holes. Fasten the camera with
screws.
4) Put the dome cover on the main
body of the camera. Make sure the
main body and the cover fit each
other into place.
5) Fasten the cover with screws.
Symmetry EN-7500 Series EN-7530 Installation Guide
9600-0545 Issue 1.1 Page 8 of 21
Caution
!
The camera may fall off the ceiling even after the proper installation and
mounting. To prevent any accident, make sure the ceiling is firm and
stable enough to support the camera. If any reinforcement is needed,
consult with your safety personnel and proceed with the installation.
4.1. Installation Template
Symmetry EN-7500 Series EN-7530 Installation Guide
9600-0545 Issue 1.1 Page 9 of 21
4.2. Manual adjustment for 3-axis movements
After installation, manually adjust the inner mechanism. Perform 3-axis movements
manually by turning the inner mechanism as shown above, and check if it moves
correctly. .
4.3. Setting the Image Attribute
You can set the image attribute of camera through the webpage.
The menu of image attribute can be seen under Setup > Video & Audio > Video-in >
Attribute Setting. Brightness, contrast, hue, saturation and sharpness can be adjusted.
4.4. Operating the OSD Menu
To operate the OSD of camera, refer to the ”EN-7530 OSD Menu Control Manual”on
the CD supplied with your manual.
Symmetry EN-7500 Series EN-7530 Installation Guide
9600-0545 Issue 1.1 Page 10 of 21
5. CONNECTIONS
5.1. Connectors
Audio In / Out
The camera has a mono audio input and a mono audio output. As the output power for
the audio is low, an amplifier is needed (Do not use a headphone or earphone directly
to the camera).
Sensor (DI) connection
The camera provides 1 channel D/I. It can be connected to either a voltage type sensor
or a relay type sensor as the following figures. It can be selected by software.
Input voltage range: 0 VDC minimum to 24 VDC maximum
Input voltage threshold: 1 V
Caution
!
Do not exceed the maximum input voltage or relay rate.
Aout
Ain
Mic
Amp Speaker
Table des matières
Autres manuels Symmetry Caméra de sécurité
