Symbol LS 4208 Manuel utilisateur
Symbol LS4208
Quick Reference Guide
2 Symbol LS4208
©2007-2008 MOTOROLA, INC. All rights reserved.
Motorola reserves the right to make changes to any product to improve reliability,
function, or design.
Motorola does not assume any product liability arising out of, or in connection with, the
application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under
any patent right or patent, covering or relating to any combination, system, apparatus,
machine, material, method, or process in which Motorola products might be used. An
implied license exists only for equipment, circuits, and subsystems contained in
Motorola products.
MOTOROLA, the Stylized M Logo and Symbol and the Symbol logo are registered
trademarks of Motorola, Inc. Other product names mentioned in this manual may be
trademarks or registered trademarks of their respective companies and are hereby
acknowledged.
Motorola, Inc.
One Motorola Plaza
Holtsville, N.Y. 11742-1300
http://www.motorola.com/enterprisemobility
Warranty
For the complete Motorola hardware product warranty statement, go to:
http://www.motorola.com/enterprisemobility/warranty
Patents
This product is covered by one or more patents. For patent information go to:
http://www.motorola.com/enterprisemobility/patents
Quick Reference Guide 3
Introduction
The Symbol LS4208 scanner combines excellent scanning performance and advanced
ergonomics to provide the best value in a lightweight laser scanner. Whether used as a
hand-held scanner or in hands-free mode in a stand, the scanner ensures comfort and
ease of use for extended periods of time. Before programming the scanner, scan the
appropriate bar code(s), beginning on page 7, to communicate with the host.
Parts
Inserting and Removing the Interface Cable
To connect the interface cable, insert the interface cable’s modular connector into the
cable interface port.
To remove the interface cable, unplug the installed cable’s modular connector by
depressing the connector clip with the tip of a screwdriver.
Aiming
Interface cable
modular connector
To host
Beeper
LED
Trigger
Scan
Window Cable interface
port
Connector
clip
4 Symbol LS4208
Scanning
Beeper Definitions
The scanner issues different beep sequences and patterns to indicate status. The table
below defines beep sequences that occur during both normal scanning and while
programming the scanner.
Beeper Sequence Indication
Standard Use
Low/medium/high beep Power up.
Short high beep A bar code symbol was decoded (if decode beeper is
enabled).
4 long low beeps A transmission error was detected in a scanned symbol.
The data is ignored. This occurs if a unit is not properly
configured. Check option setting.
5 low beeps Conversion or format error.
Lo/hi/lo beep ADF transmit error.
Hi/hi/hi/lo beep RS-232 receive error.
Parameter Menu Scanning
Short high beep Correct entry scanned or correct menu sequence
performed.
Lo/hi beep Input error, incorrect bar code or “Cancel” scanned, wrong
entry, incorrect bar code programming sequence; remain
in program mode.
Hi/lo beep Keyboard parameter selected. Enter value using bar code
keypad.
012345 012345
012345
012345
Quick Reference Guide 5
LED Definitions
In addition to beeper sequences, the scanner communicates with the user using a
two-color LED display. The table below defines LED colors that display during
scanning.
Hi/lo/hi/lo beep Successful program exit with change in the parameter
setting.
Low/hi/low/hi beep Out of host parameter storage space. Scan Set Defaults
on page 7.
Code 39 Buffering
Hi/lo beep New Code 39 data was entered into the buffer.
3 Beeps - long high beep Code 39 buffer is full.
Lo/hi/lo beep The Code 39 buffer was erased or there was an attempt to
clear or transmit an empty buffer.
Lo/hi beep A successful transmission of buffered data.
Host Specific
USB only
4 short high beeps Scanner has not completed initialization. Wait several
seconds and scan again.
Scanner gives a power-up
beep after scanning a USB
Device Type.
Communication with the bus must be established before
the scanner can operate at the highest power level.
This power-up beep occurs
more than once.
The USB bus may put the scanner in a state where power
to the scanner is cycled on and off more than once. This is
normal and usually happens when the host PC cold boots.
RS-232 only
1 short high beep A <BEL> character is received and Beep on <BEL> is
enabled.
LED Indication
Off No power is applied to the scanner, or the scanner is on and ready to
scan.
Green A bar code was successfully decoded.
Red A data transmission error or scanner malfunction occurred.
Beeper Sequence Indication
6 Symbol LS4208
Troubleshooting
Problem Possible Cause Possible Solutions
Nothing happens
when the trigger is
pulled.
No power to the
scanner.
Check the system power. Ensure the power
supply is connected if the configuration
requires a power supply.
Interface/power
cables are loose.
Check for loose cable connections.
Laser comes on,
but symbol does
not decode.
Scanner is not
programmed for
the correct bar
code type.
Ensure the scanner is programmed to read
the type of bar code scanned.
Refer to the Symbol LS4208 Product
Reference Guide, p/n 72E-69413-xx, for
more information.
Bar code symbol is
unreadable.
Check the symbol to ensure it is not defaced.
Try scanning test symbols of the same bar
code type.
Distance between
scanner and bar
code is incorrect.
Move the scanner closer to or further from
the bar code.
Symbol is decoded
but not transmitted
to the host.
Scanner is not
programmed for
the correct host
type.
Scan the appropriate host type bar code.
Scanned data is
incorrectly
displayed on the
host.
Scanner is not
programmed to
work with the host.
Ensure proper host is selected.
Check the scanner’s host type parameters or
editing options.
For RS-232, ensure the scanner’s
communication parameters match the host’s
settings.
For a keyboard wedge configuration, ensure
the system is programmed for the correct
keyboard type, and the CAPS LOCK key is
off.
Ensure editing options (e.g., UPC-E to
UPC-A conversion) are properly
programmed.
Refer to the Symbol LS4208 Product
Reference Guide, p/n 72E-69413-xx, for
more information.
Quick Reference Guide 7
Programming Bar Codes
Following are some frequently used programming bar codes.
NOTE For additional host types, refer to the Symbol LS4208 Product
Reference Guide, p/n 72E-69413-xx, available on the LS4208 CD, or
on the Symbol website: http://www.motorola.com/enterprisemobility/manuals.
Set Defaults
Scan SET DEFAULTS to set all parameters to their default values.
SET DEFAULTS
Scanning Modes
Scan the appropriate bar code below to determine the scanning pattern.
•SINGLE LINE ONLY - No up and down scan line movement (no raster).
•MULTI-LINE SMART RASTER - The scan line begins as a single line and moves up
and down (rasters) when a partial scan of a bar code is detected, or no bar code is
decoded 500 ms after the trigger is pulled.
•MULTI-LINE ALWAYS RASTER (default) - Rastering (up and down scan line
movement) begins immediately.
SINGLE LINE ONLY
MULTI-LINE SMART RASTER
MULTI-LINE ALWAYS RASTER (Default)
8 Symbol LS4208
Host Type
If a Synapse cable is used (i.e., part number STIxx-xxxx), the scanner autodetects the
Synapse cable and there is no need to scan bar codes to enable the Synapse host.
If a USB interface is used, the scanner autodetects the USB and defaults to the HID
keyboard interface. See page 10 to select the IBM hand-held host type. Refer to the
Symbol LS4208 Product Reference Guide, p/n 72E-69413-xx, for additional USB host
types.
If a Keyboard Wedge, RS-232, Wand Emulation, Scanner Emulation, or IBM 46XX is
used, the appropriate host type must be scanned. Select the appropriate host type from
the bar codes that follow.
Keyboard Wedge Host Type
Country Keyboard Types (Country Codes)
IBM PC/AT and IBM PC COMPATIBLES
NORTH AMERICAN (Default)
FRENCH Windows
FRENCH CANADIAN Windows 95/98
GERMAN Windows
French Canadian Windows XP/2000
Quick Reference Guide 9
Country Keyboard Types (Country Codes)
RS-232 Host Types
SPANISH Windows
ITALIAN Windows
SWEDISH Windows
UK ENGLISH Windows
JAPANESE Windows
PORTUGUESE-BRAZILIAN Windows
STANDARD RS-232
ICL RS-232
10 Symbol LS4208
RS-232 Host Types
USB Host Types
IBM 46XX Host Types
NIXDORF RS-232 MODE A
NIXDORF RS-232 MODE B
FUJITSU RS-232
OPOS/JPOS
HID KEYBOARD EMULATION
IBM HAND-HELD USB
PORT 5B
PORT 9B
Autres manuels pour LS 4208
5
Table des matières
Autres manuels Symbol Lecteur de codes-barres
Symbol
Symbol DS 3408 Manuel d'installation et d'exploitation
Symbol
Symbol LS1900 Series Manuel d'installation et d'exploitation
Symbol
Symbol MiniScan MS-804FZY Guide de configuration rapide
Symbol
Symbol LL 425 Manuel utilisateur
Symbol
Symbol LS 3603 Manuel d'installation et d'exploitation
Symbol
Symbol Symbol LS2208 Manuel utilisateur
Symbol
Symbol LS 2104 Mode d'emploi
Symbol
Symbol LS9203 Manuel
Symbol
Symbol LS 9100 Manuel d'installation et d'exploitation
Symbol
Symbol 3100 Series Manuel d'installation et d'exploitation
Symbol
Symbol SPS 3000 Series Manuel
Symbol
Symbol CS1504 Manuel utilisateur
Symbol
Symbol DS6707-SR20007ZZR Manuel utilisateur
Symbol
Symbol SE955 Guide de configuration rapide
Symbol
Symbol LS4278 Manuel utilisateur
Symbol
Symbol CRD3100-1000 Manuel utilisateur
Symbol
Symbol LS1203 Manuel utilisateur
Symbol
Symbol LS3578 Manuel d'installation et d'exploitation
Symbol
Symbol LS 4208 Manuel utilisateur
Symbol
Symbol MC909X-K Manuel utilisateur
Manuels Lecteur de codes-barres populaires d'autres marques
POSMicro
POSMicro Datalogic PowerScan D7100 Manuel utilisateur
Marson
Marson MT780 Guide de configuration rapide
NCR
NCR RealPOS Manuel utilisateur
Motorola
Motorola SE3300 Guide de configuration rapide
Element
Element P130BT Manuel utilisateur
Motorola
Motorola Symbol LS3008 Manuel d'installation et d'exploitation
