SWIT Electronics CM-55C Manuel utilisateur
QUICK GUIDE
5.5″ 4K HDMI Monitor
CM-55C
INTERFACES AND BUTTONS
Power Switch
DC IN
Battery Input
BATT OUT
HDMI IN
Remote
Switch to“
|
”position to power on;
and switch to “o” position to power off
DC power input, 5～17VDC，Micro USB
External battery NP-F or LP-E6, 6V～8.4V
Battery output
HDMI input interface
compatible DVI1.0, HDMI Type-A
Remote control, headphone output,
2.5mm Stereo Jack
Headphone output jack, 3.5mm stereo Jack
SD card slot, the SD card is used to load the
customized LUT tables, and update the
monitor firmware.
SD Card Slot Remote Control
HDMI Input
Power Switch
DC Power Input
Micro USB
Headphone
Battery Input
Battery output
❶ Install the battery or connect the power cord.
❷ Switch the power switch to “一”position, the monitor will
be powered on.
* It will display the boot screen after power on for 3~4 seconds.
* The BATT OUT interface directly outputs battery power when
battery is mounted.
* Only use the adapter and the power cord specified by the
manufacture for your safety!
POWER ON
Joystick
Joystick provides five operation directions, Up Down, Left,
Right, and Straight Down. Use the joystick as a navigation
tool to scroll between scenes pages and set features.
BUTTONS OPERATION
: scroll it leftmost to enter into the monitor settings menu
: scroll it right to enter into a scene or create a scene mode
: scroll it up to enter into ZOOM mode
: cancel the settings, return to the previous menu or quit
menu settings.
: scroll it down to confirm the current operation or selection
JOYSTICK
SCENE MODE
Enter a Scene
It will display a scene as default after powered on. Scroll the
joystick right or left to switch among scenes.
Scroll the joystick down to return a scene when in ZOOM mode.
Scroll the joystick right to return a scene when in monitor
settings menu.
Add a Scene
Hold the joystick right for 3 seconds, it will prompt “Add
New MySet ” command in the bottom center of the
screen, press the joystick straight down to confirm the
operation. It supports up to 8 customized scenes.
The scene will be numbered in sequence, and the name will
be displayed at the left bottom of the screen, e.g., .
Delete a Scene
Scroll the joystick down in a scene, it will display the DELETE
command at the bottom of the screen, press the joystick
straight down to confirm deletion. The DELETE command is
not available when there is only one scene.
SCENE TOOL
Add a Tool in a Scene
In a scene, scroll the joystick down, it will pop up the “ADD
NEW TOOL” command. Press the joystick straight down to
confirm, it will display Tools Menu on the left side of the
screen, scroll the joystick up or down to select your desired
scene tool, and press the joystick straight down to confirm.
Enable/Disable a Tool
In a scene, press straight down the joystick to display the
scene tool, and then scroll the joystick left to close the
scene tool in current scene.
IMAGE ZOOM
Scroll up the joystick to enter into image zoom mode,
double(2X) or quadruple(4X) the image, and move the
starting position of the enlarged image.
❶ Enter ZOOM Mode
In a scene, scroll up the joystick to enter into image zoom
2X mode, and there will be a 2X zoom icon at the right
bottom corner of the screen, continue to scroll up the
joystick to to enter into image zoom 4X mode.
Scroll Up Once
Scroll Up Twice
❷ Adjusting Mode
Press straight down the joystick to move the starting
position of the enlarged image.
Then, the icon is changed, there will be four arrows at each
direction surrounding the center rectangle.
Press straight down the joystick to confirm the adjustment.
* In 2X or 4X zoom mode, press straight down the
joystick, it will recover and display the original image.
Rotate Screen
Hold the joystick left for 3 seconds to enter the monitor
settings menu;
Scroll down to select controls→DISPLAY ROTATE item,
and press straight down the joystick to display the
DISPLAY ROTATE submenu. Scroll right or left to set the
SCREEN ROTATE item to be 180, then the input image will
reverse vertically. Set the IMAGE ROTATE as the same way.
Restore the Factory Settings
Select monitor settings menu, and select system→
FACTORY RESET item, then scroll right to select EXECUTE
FACTORY RESET command, and press the joystick straight
down to confirm the selection to initialize the settings to
default values.
SWIT Electronics Co., Ltd.
Add: 10 Hengtong Road, Xin'gang, Nanjing Economic and
Technological Development Zone, Nanjing 210038, P.R.China
Tel: +86-25-85805753 Email: contac[email protected]c
SWIT Electronics Europe GmbH
Add: Hochstr. 17, 47228 Duisburg, Germany
Tel: +49(0)20659799339 Email: info@swit-europe.com
SWIT Electronics America, Inc
Add: 3350 Scott Boulevard 61-02, Santa Clara, CA 95054, USA
Tel: (408)260-8258, 1-866-986-SWIT(7948) Email: [email protected]
Table des matières
Autres manuels SWIT Electronics Moniteur
SWIT Electronics
SWIT Electronics M-1092H Manuel utilisateur
SWIT Electronics
SWIT Electronics M-1093F Manuel utilisateur
SWIT Electronics
SWIT Electronics BM-U175HDR Manuel utilisateur
SWIT Electronics
SWIT Electronics BM-U243 Manuel utilisateur
SWIT Electronics
SWIT Electronics S-1073F Manuel utilisateur
SWIT Electronics
SWIT Electronics FM-24DCI Manuel utilisateur
SWIT Electronics
SWIT Electronics BM-U Series Manuel utilisateur
SWIT Electronics
SWIT Electronics FM-21HDR Manuel utilisateur
SWIT Electronics
SWIT Electronics FM-17 Manuel utilisateur
SWIT Electronics
SWIT Electronics S-1273F Manuel utilisateur
