Swagelok BS20 Manuel utilisateur
BS(H)20
USER MANUAL
Read the complete manual before installing and using the regulator.
2
BS(H)20 User Manual
Rev.date: 20-09-2010
CONTENTS
1Introduction......................................................................................................................................... 4
1.1Description.................................................................................................................................... 4
2Installation........................................................................................................................................... 4
2.1 Points of attention before installation ........................................................................................... 4
3Operation............................................................................................................................................. 4
4Maintenance........................................................................................................................................ 5
4.1Disassembly ................................................................................................................................. 5
5Trouble shooting................................................................................................................................ 6
3
BS(H)20 User Manual
Rev.date: 20-09-2010
WARNING
INCORRECT OR IMPROPER USE OF THIS PRODUCT CAN CAUSE SERIOUS PERSONAL
INJURY AND PROPERTY DAMAGE.
Due to the variety of operating conditions and applications for this product, the user is solely
responsible for making the final proper decisions concerning the correct assembly and functioning of
the product and assuring that all the performance, safety and warning requirements are met.
•Users must be trained and equipped for the handling, use and servicing of pressure products
and systems.
•Users must contact their gas or liquid supplier for specific safety precautions and instructions.
•Gaseous media should be free of excessive moisture to prevent icing at high flow.
•Always wear the appropriate protective clothing, including safety glasses, gloves etc. if
required.
•Follow the applicable safety and maintenance procedures.
•Obey specific local regulations.
•Do not exceed the maximum inlet and outlet pressure of the product or its accessories.
•Operate within the temperature limits and other conditions specified for the product.
•Do not drop or damage the product in any other way. This may negatively effect the
performance of the product which can cause the product to malfunction.
•Venting fluids and gases can be dangerous. Vent to a safe environment away from people.
Ensure adequate ventilation.
•This product is not oxygen clean and therefore not suitable for oxygen service.
If there are questions or problems regarding the installation, operation and maintenance these should
be directed to the proper authority on site before continuing.
4
BS(H)20 User Manual
Rev.date: 20-09-2010
1 Introduction
The function of a backpressure regulator is to maintain constant and to control an inlet pressure with a
variable flow.
These series are self contained, spring loaded, manually adjustable regulators.
They are suitable for high pressure gases and liquids and will relieve accurately over a wide variable range.
The regulators are soft seated for leak tight shut-off in zero flow conditions.
Note however, that a backpressure regulator is not a shut-off valve and should not be used as such.
The maximum supply pressure is:
- 70 bar for models BS20
- 250 bar for models BSH20
The maximum outlet pressure is:
- 70 bar for models BS20
- 250 bar for models BSH20
- Flanges models: depends on the pressure rating of the flanges.
1.1 Description
The regulator comprises a body and spring housing joined together by bolts. The body has a removable
seat, and valve assembly.
A sensing element is inserted in the spring housing.
The regulators are in a high accuracy format with a large diaphragm or piston combined with a strong
spring. This gives a relatively high knob torque which could be undesirable for frequent readjustment type
applications.
2 Installation
Ensure that the regulator is installed in the proper flow direction. Fit the regulators with bspp parallel
connections, preferably with bonded seals:
- for BS(H)20: 2" bspp
- for BS(H)F20: see flange type on the applicable assembly drawing.
Avoid sealing compounds which harden. Be careful with anaerobic (Loctite type) compounds.
These compounds can run into the regulator and lock moving parts.
2.1 Points of attention before installation
Carefully clean all pipes and connections. Any swarf, lint, wire etc. may cause seat leakage.
If possible the system should contain a filter.
Shut-off valves should be installed.
3 Operation
- Controlled pressure settings are obtained by adjusting the setscrew. Rotating the screw clockwise
raises the set pressure while counterclockwise rotation lowers the set pressure.
- Gaseous media should be free of excessive moisture to prevent icing.
5
BS(H)20 User Manual
Rev.date: 20-09-2010
4 Maintenance
All regulators require maintenance at scheduled intervals. The only parts liable to deterioration are the valve
seat, O-rings, back-up rings and diaphragms.
Annual replacement of all soft parts is recommended under normal use.
More frequent maintenance may be required in heavy duty service.
4.1 Disassembly
Piston models.
- Turn set screw counter clockwise.
- Loosen bolts.
- Remove spring housing, set spring, spring guide.
- Loosen retaining ring.
- Remove the piston-valve assembly.
- Remove body plug and seat.
Now all soft parts are accessible for replacement.
Reverse the process for assembly.
Diaphragm models
- Turn setscrew counterclockwise.
- Loosen bolts.
- Remove spring housing, spring, spring guide.
- Loosen retaining ring.
- Remove the diaphragm-valve assembly.
- Remove body plug and seat.
All soft parts are now accessible for replacement.
To replace the diaphragm, unscrew clamp screw.
Reverse the process for assembly.
6
BS(H)20 User Manual
Rev.date: 20-09-2010
5 Trouble shooting
Problem: Constant leakage from the outlet port before the relief set pressure is reached.
Cause: A damaged valve and/or valve stem.
Solution: Replace the valve and/or the valve stem.
Problem: Constant leak of pressure into the spring housing discharging through the vent connection.
Cause: A damaged or ruptured diaphragm (if fitted) or a damaged piston.
Solution: Replace.
Problem: The regulator will not relief at the set point.
Cause: The valve stem is sticking or the control knob needs re-adjusting.
Solution: Replace.
Warranty Information
Swagelok products are backed by The Swagelok Limited Lifetime Warranty.
For a copy, visit swagelok.com or contact your authorized Swagelok representative.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Swagelok Contrôleurs
Swagelok
Swagelok KPP Series Caractéristiques techniques
Swagelok
Swagelok KHB Series Caractéristiques techniques
Swagelok
Swagelok RHPS Series Manuel utilisateur
Swagelok
Swagelok KSV Series Caractéristiques techniques
Swagelok
Swagelok LBS4 Manuel utilisateur
Swagelok
Swagelok RHPS Series Manuel utilisateur
Swagelok
Swagelok KBP Series Caractéristiques techniques
Swagelok
Swagelok RHPS Series Manuel utilisateur
Swagelok
Swagelok RHPS Series Manuel utilisateur
Swagelok
Swagelok KPB Series Caractéristiques techniques
Swagelok
Swagelok RHPS Series Manuel utilisateur
Swagelok
Swagelok PRS15 Manuel utilisateur
Swagelok
Swagelok RHPS Series Manuel utilisateur
Swagelok
Swagelok KFB Series Caractéristiques techniques
Swagelok
Swagelok BSH 10 Series Manuel utilisateur
Swagelok
Swagelok KCP Series Caractéristiques techniques
Swagelok
Swagelok KCB Series Caractéristiques techniques
Swagelok
Swagelok TBVS8 Manuel utilisateur
Swagelok
Swagelok RHPS Series Manuel utilisateur
Swagelok
Swagelok RHPS Series Manuel utilisateur
