Suptek MC4602 Manuel utilisateur
Model Number：MC4602
Display Size：up to 55＂
Maximum Load：45KG
Mounting Pattern：400mmX400mm
Tilt Range：15°
Profile：580mm-900mm
Product Components
Pedestal*1 Junction Plate*1Outer Pole*1 Inner Pole Connector*1 faceplate*1 Hang hook*2
Screw Package 1
Screw Package 2
A-M6*12 Semicircle
Hexagon*2
B-M6 Nut*2 C-M4 Allen Key*1 D-M8*50 Outer
Hexagonal Screw*2
F-M8 Nut*3 H-M8*45 Screw*1 I-M8
Locking Nut*2
A-Plastic
Anchors*4
B-Drilling
Screw*4
D-M8*25 Screw*4 E-M6*25 Screw*4 F-M5*25 Screw*4 G-M4*25 Screw*4 H-Φ5Washer*4 I-Φ6Washer*4
G-Φ8Washer*5E-M8*20*4
Spacer*4
C- Φ8 Spacer*4
The way of Connection 1
The way of Connection 2
Insert the outer pole into the center hole
of the pedestal as shown in the diagram.
This way of connection is for 360°rotation
adjustment.
Use Screw Package 1
The First Step:Pedestal And Outer Pole Connection(One way is for ±90°Front and rear adjustment;Another way is for
360°rotation adjustment; Customers can choose the way which is needed)
Installation Steps
Outer Pole
Pedestal
360°
The assembly of the Pedestal
and the Junction Plate is shown
in the diagram.
Use Screw Package 1
Junction Plate
Pedestal
C-M4 Allen Key
A-M6*12
Semicircle Hexagon
B-M6 Nut
The assembly of the Outer Pole and the
Junction Plate is shown in the diagram.
This way of connection is for ± 90° Front
and rear adjustment.
G-Φ8Washer
E-M8*20*4
Spacer
Pedestal
Junction Plate
F-M8 Nut D-M8*50 Outer
Hexagonal Screw
Customers can choose
installation angle which
is needed.
G
-
H-M
G -
C
D
E
F
G
HI
D
E
F
G
HI15°
3°
Pedestal
The Second Step: Install the Wall Piece
Place the pedestal against the wall, mark off the holes then drill. Insert plastic anchors into each hole,secure pedestal with self-drilling screw
as shown in the diagram
A-Plastic Anchors
B-Self-Drilling Screw
Use Screw Package 2
The Third Step:
Connection of Inner Pole Connector and Outer Pole
The Fourth Step:
Connection of Faceplate and Junction Plate
F-M8 Nut 8*45 Screw
8 Washer
Use Screw Package 1 Use Screw Package 1
Plastic knobs
I-M8 Self - Locking
Nut*2
8 Washer
The Fifth Step:Install the Hook And Display The Sixth Step:Install the Hook And Faceplate
Use Screw Package 2
Use Screw Package 2
no washer if use the screw D
no washer if use the screw D
no spacer with the flat back spacer needed with curved back
or
or
Hang the two hooks
into the faceplate
Tighten the bottom
screw,and stand up
the bottom of the faceplate.
Unscrew the plastic knob,
faceplate can be adjusted up and down,
adjust to the appropriate position and tighten again
Plastic
knobs
Please check the screws is fixed or not every two months .
after-sales@suptekmount.com
Autres manuels Suptek Support et étagère
Suptek
Suptek MA2720 Manuel utilisateur
Suptek
Suptek MD9401 Manuel utilisateur
Suptek
Suptek ML5074 Manuel utilisateur
Suptek
Suptek ML5074-3 Manuel utilisateur
Suptek
Suptek MA2720 Manuel utilisateur
Suptek
Suptek MD8SP Manuel utilisateur
Suptek
Suptek ML5074-2 Manuel utilisateur
Suptek
Suptek ML6802 Manuel utilisateur
Suptek
Suptek MD6411 Manuel utilisateur
Suptek
Suptek MD94X2 Manuel utilisateur
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
