Sun Oracle Netra SPARC T3-1B Manuel utilisateur

This guide describes the minimum steps required to install and power on Oracle’s Netra SPARC T3-1B server

module for the first time.

For more detailed installation information, refer to the online Netra SPARC T3-1B Server Module Installation Guide

and the installation guide for your Sun Netra 6000 modular system. Also read the latest Netra SPARC T3-1B

Server Module Product Notes to find out if any late-breaking issues impact installation requirements:

http://www.oracle.com/pls/topic/lookup?ctx=E21652-01&id=homepage

Shipping Kit Contents

▼Install Optional Components

♦Before installing the server module into the modular system chassis, install any optional components that

you ordered for the server module.

Optional components might already be installed in the server module you received. See the customer

information sheet for details. For instructions on installing optional components, refer to the documentation

for each component and the Netra SPARC T3-1B Server Module Service Manual.

Figure Legend

1Printed documentation

2Server module

3Shipping carton

4Customer information sheet (save this for MAC

addresses and other information)

Netra SPARC T3-1B Server Module

Getting Started Guide

▼Install the Server Module Into the Chassis

The server module is hot-pluggable in the chassis. The instructions in this guide assume that the Sun Blade

6000 modular system is installed, and is up and running.

1. Remove the filler panel from the desired server module slot in the chassis.

Be ready to insert the server module or a filler panel in the empty slot within 60 seconds.

2. Insert the server module in the chassis (panel 1) until it is about 1.5 cm (.5 in.) from the front of the

chassis.

The side of the server module with the service label faces to your right.

3. Extend the ejector levers (panel 2), then push the ejector levers in simultaneously until they lock in place

(panel 3).

4. Verify the server module insertion by checking the green OK LED on the server module (panel 4).

When the server module is plugged in, standby power is supplied to the service processor (SP). The front

panel LEDs blink three times, then the green OK LED on the front panel blinks for a few minutes. The server

module SP generates diagnostic messages as soon as the server module is connected to a powered modular

system.

Caution – For proper cooling, ensure that all slots are filled with a server module or a filler panel. Fill

all slots within 60 seconds after the modular system is connected to power.

▼Determine Your Connection Method

You can start, boot, and manage the server module using the Oracle Integrated Lights Out Manager (ILOM)

software that runs on the server module SP. You can also control the server module from Oracle ILOM

running on the chassis management module (CMM) of the modular system.

There are several ways that you can connect to the server module SP.

♦Connect to the server module using one of the methods shown in the following figure and table.

This guide uses method 1, but you can use the other methods as described in the Netra SPARC T3-1B Server

Module Installation Guide.

Method Connection Description

1 Ethernet

From: CMM NET MGT port

To: Your network

(This guide includes details on this method)

Ensure that the CMM NET MGT port is connected to your network.

From your network, log into Oracle ILOM on the CMM using the IP address

of the CMM. Use the Oracle ILOM proxy to navigate to the server module SP

Oracle ILOM interface. You can use the Oracle ILOM command-line interface

(CLI) or use the CMM Oracle ILOM web interface (as described in “Access

Oracle ILOM on the Server Module SP (Web Interface)” ).

2 Serial

From: CMM SER MGT port

To: Terminal device

Connect a terminal device to the CMM SER MGT RJ-45 port and use Oracle

ILOM to navigate to the server module SP Oracle ILOM interface. This

method only supports the Oracle ILOM CLI.

3 Serial

From: Server module SP UCP port

(dongle required)

To: Terminal device

Connect a UCP-3 dongle cable to the server module. Connect a terminal

device to the RJ-45 connector on the dongle cable. Communicate with Oracle

ILOM on the server module SP using the Oracle ILOM CLI.

▼Access Oracle ILOM on the Server Module SP (Web Interface)

This procedure is for method 1, which uses a web interface through the CMM to access the server module Oracle

ILOM CLI. You must know the CMM IP address to perform this procedure. This procedure also assumes you

have a DHCP environment. For other environments, see instructions in the SPARC T3-1B Server Module

Installation Guide.

1. Ensure that the CMM NET MGT port is connected and configured to communicate on your network.

Refer to the Sun Blade 6000 modular system documentation for details.

2. In a browser on the same network as the modular system, enter the IP address of the CMM.

For example, if your CMM has the IP address 129.99.99.99, direct your browser to that address. A login

window for Oracle ILOM will appear.

3. Log in to Oracle ILOM on the CMM by typing your user name and password.

The factory default Oracle ILOM root password is changeme.

You are now logged in to the CMM Oracle ILOM web interface.

4. Navigate to the server module SP.

a. Select the chassis view for the modular system.

b. Click on the image of the server module that you have installed in the modular system.

The slots in the modular system are numbered from 0 to 9.

5. Start the Remote Console.

a. Select Remote Control on the top menu.

b. Select the Redirection tab.

c. Click on Use serial redirection.

d. Click on Launch Remote Console.

6. Power on the server module.

a. Select the Remote Power Control tab.

b. Click on the menu in that tab and select Power On.

c. Select Save.

d. Select OK when you see this prompt: Are you sure you want to perform a Power On of the server.

The server module host is powered on for the first time. The server module hardware installation is complete

and the server module is ready to be configured to suit your needs. For details on the Oracle Solaris OS

configuration process, see the Netra SPARC T3-1B Installation Guide and the installation guides for your

version of Oracle Solaris OS.

▼Power On the Server Module Host

If you used a command line method to access the server module SP, rather than use the procedure in “Access

Oracle ILOM on the Server Module SP (Web Interface)” , you need to use this procedure to power on the server

module host.

1. Power on the server module host.

The server module initializes.

2. Switch communication to the server module host.

The server module might take several minutes to complete POST. If a boot device installed with the Oracle

Solaris OS is accessible locally, the server module boots. Otherwise, the system uses the boot net command

to seek a boot device on the network.

You are now connected to the server module host.

The server module hardware installation is complete and the server module is ready to be configured to suit

your needs. For details on the Oracle Solaris OS configuration process, see the Netra SPARC T3-1B Server

Module Installation Guide and the installation guides for your version of Oracle Solaris OS.

▼Check for the Latest OS, Patches, and Firmware

Later versions of OS, patches, and firmware might be available for your server module. Some features can

only be enabled when certain patches or firmware are installed. Install the latest available versions for the

best performance, security, and stability.

1. Review the SPARC T3-1B Server Module Product Notes at:

http://www.oracle.com/pls/topic/lookup?ctx=E21652-01&id=homepage

This document describes important product dependencies and late-breaking information.

2. Access the latest OS, patches, and firmware information from the system administration portal:

http://www.oracle.com/technetwork/systems/software-stacks/stacks/index.html

Under the Netra Carrier-Grade Systems heading, select the Netra SPARC T3-1B Server Module link.

-> start /SYS

Are you sure you want to start /SYS (y/n)? y

Starting /SYS . . .

-> start /HOST/console

Are you sure you want to start /HOST/console (y/n)? y

Serial console started. To stop, type #.

Accessing Additional Information

Find the documentation for Oracle’s Netra SPARC T3-1B server module at:

http://www.oracle.com/pls/topic/lookup?ctx=E21652-01&id=homepage

Product Documentation

You can view, print, or purchase a broad selection of documentation, including localized versions, at:

http://www.oracle.com/technetwork/documentation/index.html

Technical Support

If you have technical questions about this product that are not answered in this document, go to:

https://support.oracle.com

Task Document Title or URL

Review known issues, workarounds, and

new information.

Netra SPARC T3-1B Server Module Product Notes

Connect to server module for initial

installation and configuration.

Netra SPARC T3-1B Server Module Installation Guide

Set remote access. View system status and

event logs.

SPARC T3 Series Servers Administration Guide

Diagnose and troubleshoot the server

module. Remove and replace components.

Netra SPARC T3-1B Server Module Service Manual

Review safety information. Netra SPARC T3-1B Server Module Safety and Compliance Manual

Important Safety Information for Sun Hardware Systems

Access chassis-specific hardware and Oracle

ILOM information.

http://www.oracle.com/technetwork/documentation/netra-

blade-servers-252766.html

Access preinstalled OS information. http://www.sun.com/software/preinstall

Part No.: E21658-01,

Mfg No.: 7012752,

April 2011

Autres manuels pour Netra SPARC T3-1B

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Sun Oracle Serveur

Sun Oracle

Sun Oracle SF2EP Manuel d'installation et d'exploitation

Sun Oracle

Sun Oracle X3-2 Manuel utilisateur

Sun Oracle

Sun Oracle X3-2L Manuel technique

Sun Oracle

Sun Oracle Fire X4470 Manuel utilisateur

Sun Oracle

Sun Oracle Sun Dual 10GbE SFP+ PCIe ExpressModule Manuel utilisateur

Sun Oracle

Sun Oracle SPARC T4-4 Manuel utilisateur

Sun Oracle

Sun Oracle Netra 6000 Manuel utilisateur

Sun Oracle

Sun Oracle T5220 Manuel utilisateur

Sun Oracle

Sun Oracle Sun Blade 6048 Manuel de service

Sun Oracle

Sun Oracle SPARC T3-1 Manuel utilisateur

Sun Oracle

Sun Oracle Sun SPARC Enterprise M3000 Manuel de service

Sun Oracle

Sun Oracle SPARC T3-1 Manuel utilisateur

Sun Oracle

Sun Oracle X2-4 Manuel utilisateur

Sun Oracle

Sun Oracle NETRA SPARC T4-1 Manuel utilisateur

Sun Oracle

Sun Oracle Blade X4-2B Manuel utilisateur

Sun Oracle

Sun Oracle Netra X6270 Manuel utilisateur

Sun Oracle

Sun Oracle Netra SPARC T3-1BA Manuel d'installation et d'exploitation

Sun Oracle

Sun Oracle SPARC Enterprise M9000 Manuel utilisateur

Sun Oracle

Sun Oracle T5120 Manuel utilisateur

Sun Oracle

Sun Oracle Sun Ray 3i Client Manuel utilisateur

Sun Oracle

Sun Oracle Netra X4250 Manuel technique

Sun Oracle

Sun Oracle T4BLD Manuel d'installation et d'exploitation

Sun Oracle

Sun Oracle Fire X4440 Manuel utilisateur

Sun Oracle

Sun Oracle Blade X4-2B Manuel utilisateur

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur