Stuart Turner Mainsboost Plus Mode d’emploi

mainsboost

Read this manual carefully before commencing installation.

This manual covers all Mainsboost Plus vessels for vertical and horizontal units.

Mainsboost Plus

Mainsboost Plus Installation, Operation

& Maintenance Instructions

Please leave this instruction booklet with the home owner as it contains

important guarantee, maintenance and safety information

3 year guarantee on pump and ttings

CE compliant product

- 2 -

Cont ...

PRODUCT DESCRIPTION

Mainsboost Plus consists of three key assemblies, the Mainsboost vessel, charger MJ3

pump and upstream line-in kit.

APPLICATION

Mainsboost Plus is designed to offer stored clean, potable cold water under pressure for

all domestic or small commercial applications where mains water is insufficient to offer

consistent and reliable water services.

Installation parameters must not exceed the values given in the technical

specifications.

zMainsboost Plus system must not be used for

any other application without the written consent

of Stuart Turner Limited.

zThis appliance can be used by children aged from

8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of

experience and knowledge if they have beengiven

supervision or instruction concerning use of the

appliance in a safe way and understand the

hazards involved. Children shall not play with

the appliance. Cleaning and user maintenance

shall not be made by children without supervision.

zChildren should be supervised to ensure that they

do not play with the appliance.

Please read installation details carefully as they are intended to ensure this

product provides long, trouble free service. Failure to install the unit in

accordance with the installation instructions will lead to invalidation of the

warranty. These instructions must be left with the product.

STORAGE

If this product is not to be installed immediately on receipt, ensure that it is stored in a dry,

frost and vibration free location in its original packaging.

- 3 -

Cont ...

CONTENTS Page

Checklist ................................................................4

Introduction .............................................................6

Important Facts - read before commencing installation ...........................7

Location ................................................................8

Terminology .............................................................9

Conguration ............................................................10

Installation ..............................................................12

Electrical ................................................................17

Commissioning ...........................................................19

Technical Specication .....................................................22

Trouble Shooting .........................................................24

Guarantee ...............................................................25

- 4 -

Cont ...

CHECKLIST

Item Description Qty Item Description Qty

Package

1 ¼ “ BSP pressure gauge 2 Package

21 Mainsboost vessel 1

2 Lever isolating ball valve 1 Package

31 Pump 1

3Pressure vessel connector

fitting 1 2 Manifold Assy 1

46 bar pressure regulating

valve 1 3 Pressure relief valve 1

5 ¼ x ½ “ BSP Brass bush 1 4 Hose 2

6 Y pattern inline strainer 1 5 Sealing washer 2

7 Double check valve 1 6 Pump mounting bolt

assy 1 set

8 1¼ “ BSP Pressure gauge 1

Your product may vary slightly from the picture above.

Mainsboost Plus (Vertical)

IMPORTANT: Your Mainsboost Plus water performance system will be delivered

in a minimum of three boxes on one pallet. Please check the contents within

24 hours of receipt and if any component is damaged, please contact Stuart

Turner Ltd immediately.

Package 2

Mainsboost vessel

Fig. 3

Package 1

Upstream line-in kit

Fig. 1

Package 3

MJ3 pump

Fig. 2

- 5 -

Cont ...

CHECKLIST

Mainsboost Plus (Horizontal) (available in MBP 200SH and MBP 250SH vessels only)

Mainsboost Plus horizontal is supplied with the pump assembly pre-assembled onto the

cylinder.

Your product may vary slightly from the picture above.

Item Description Qty Item Description Qty

Package

1 ¼ “ BSP pressure gauge 2 Package

21 Pump assembly 1

2 Lever isolating ball valve 1 2 Pump bracket 1

3Pressure vessel connector

fitting 1 3 Mainsboost vessel 1

46 bar pressure regulating

valve 1 4 Mounting cradles 1

5 ¼ x ½ “ BSP Brass bush 1 5 Hose 2

6 Y pattern inline strainer 1

7 Double check valve 1

8 1¼ “ BSP Pressure gauge 1

928 mm x 28 mm x 22 mm

Tee 1

Package 1

Upstream line-in kit

Fig. 4

Package 2

MJ3 pump

Fig. 5 4

5 (Hoses supplied

loose shown as such)

- 6 -

Cont ...

1 INTRODUCTION

1.1 Congratulations on buying a Mainsboost Plus system, designed to offer

consistent and reliable water services throughout the property and the only

system available that is patent protected No. GB2349908.

1.2 Patents, Trademarks & Trade Names:

‘Mainsboost’ ‘Mainsboost Plus™’ and ‘Mainsboost Charger’ are

registered Trademarks of Stuart Turner Ltd.

The use of this system is patent protected and the Mainsboost Plus vessel

cannot be mixed with other accumulator systems without prior approval from

Stuart Turner Ltd.

The Mainsboost Plus vessels have special characteristics and the use of other

vessels in this application could prove to be detrimental to the design and

performance of the system and the patent.

Stuart Turner Ltd will treat any infringement of the patent very seriously and

therefore recommend that any questions regarding application be brought to the

company for consideration.

1.3 How the Mainsboost Plus System works:

The Mainsboost Plus pressure vessel stores water from the rising main in a

sealed water chamber, separated from the air space by a rubber diaphragm and

pressurised to an optimum setting. When water is drawn off by downstream

services, the water from the mains is supplemented by the water from the

Mainsboost Plus unit to provide a balanced supply at consistent pressure to

downstream services.

The Mainsboost Plus pipework manifold incorporates a unique ‘green energy’

bypass. If the incoming mains water supply delivers more than 12 l/min this

bypass should be left open to allow any additional flow rate to pass directly into

the Mainsboost pressure vessel via the integral non-return valve. If the

incoming flow rate is less that 12 l/min the bypass valve should be left closed

in order to ensure optimum efficiency of the Charger MJ3 pump.

- 7 -

Cont ...

2 IMPORTANT FACTS READ BEFORE COMMENCING INSTALLATION

A. Commissioning

2.11 Ensure the pump is primed as described in the priming section before starting,

damage to the shaft seal will result otherwise. See Section 8.16 -

Commissioning.

B. Water temperature

This unit is designed for cold water applications only which should not exceed the

following values:

2.12 The maximum allowable water temperature is 35 oC.

2.13 The minimum allowable water temperature is 4 oC.

C. Pipework - General

2.14 Secure pipework: Ensure pipework to and from the Mainsboost Plus is

independently supported & clipped to prevent forces being transferred to inlet

and outlet branches of pump. Flexible hoses supplied must be used.

2.15 Flux: Solder joints must be completed and flux residues removed prior to pump

installation (flux damage will void any warranty).

2.16 Pipework design: Care should be taken in the design of pipework runs to

minimize the risk of air locks e.g. use drawn bends rather than 90obends.

D. Plumbing Installation Regulations

2.17 The plumbing installation must comply with the current water and building

regulations.

2.18 The plumbing installation must be installed by a qualified person.

2.19 The electrical installation must be carried out in accordance with the current

national electrical regulations.

2.20 The electrical installation must be installed by a qualified person.

E. Mainsboost vessel

2.21 Ensure the Mainsboost vessel is installed correctly before operating the unit, to

avoid damage to the pumps/controls.

Do not attempt to dismantle the Mainsboost vessel

The Mainsboost vessel is pressurised to a pre-set level at the factory see

Section 8.12 - Commissioning for details.

- 8 -

Cont ...

3 LOCATION - GENERAL

3.11 Access: For emergencies and maintenance the Mainsboost Plus

must be easily accessible.

3.12 Protection: The system must be located in a dry position, and

protected from freezing. Avoid environments which have a high

ambient temperature, high humidity or excessive condensation

and salt damage, etc.

3.13 Ventilation: Ensure an adequate air flow to cool the pump.

Separate the pump from other appliances that generate heat.

3.14 Safety: The motor casing can become very hot under normal

operating conditions. Care must be taken to ensure it cannot be

touched during operation.

3.15 Water retention: Site the pump in a location where in the unlikely

event of a water leak, any spillage is contained or routed to avoid

electrics or areas sensitive to water damage.

3.16 Static inlet pressure: Ensure the static inlet head at the pump does not

exceed the values shown in the table under point 8.14.

3.17 Incoming mains water pressure: The incoming water pressure of at least

0.1 bar is required.

3.18 Ensure that location of the unit allows adequate space to give reasonable access

to all parts to accommodate service/commissioning.

3.19 Ambient temperature: The pump must be sited in a location where the

maximum ambient temperature does not exceed 40 oC.

3.20 Pipework: Pipework should be sized to ensure optimum performance of the

system.

3.21 Direction of flow: See Fig. 6 (vertical), Fig. 7 (horizontal) to identify the suction

and discharge connections.

Vertical

Fig. 6

Suction

Discharge

Horizontal

Fig. 7

Suction

Discharge

- 9 -

Cont ...

4 TERMINOLOGY

4.11 System Designation:

It is important to understand what upstream and downstream refers to before

starting the installation.

4.12 Upstream

The term ‘Upstream’ refers to the system configuration from the consumer’s

stopcock to the point where the supply reaches the inlet port of the Mainsboost

Plus Pump.

4.13 Downstream

The term ‘Downstream’ refers to the system configuration from the outlet tapping

on the Mainsboost Plus Pump, along the distribution header (if configured in

this way) and into the distribution pipework and outlets. This includes hot and

cold services where both are present (see Fig. 8).

Fig. 8 System designation

- 10 -

Cont ...

5 CONFIGURATION

5.11 Mainsboost Plus is a very flexible solution, offering a patent protected packaged

system to suit any type or size of building no matter how large or small the

demand is. The following illustrations depict just some of the most typical

installations.

5.12 Single occupancy application:

Use of Mainsboost Plus in a

house offers water on

demand whilst giving

maximum flexibility. As can

be seen the upstream

line-in kit has to be fitted on to

the rising main but the vessel/

pump can be fitted wherever

there is a space, for example;

utility, kitchen, upstairs

cupboard or loft, providing

adequate provisions are taken

for the weight, frost protection

etc (see Fig 9).

Where height restrictions exist

the MPB 200SH and

MBP 250SH litre Mainsboost

Plus can be supplied for

horizontal installation.

5.13 Multiple occupancy application:

Often affected by poor water

supplies Mainsboost Plus

offers the perfect solution.

For multiple occupancy

buildings again the

upstream line-in kit is located

next to the rising main and

sized to meet the demand of

the entire building. Each

apartment then has its own

vessel and pump located

within the property, sized to

meet the apartments own

demand (see Fig. 10).

Fig. 9

Fig. 10

Table des matières

Autres manuels Stuart Turner Système d'eau

Stuart Turner

Stuart Turner Mainsboost MB 100SV Mode d’emploi

Manuels Système d'eau populaires d'autres marques

Spirotech

Spirotech SPIROVENT SUPERIOR S250 Manuel utilisateur

Culligan

Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water... Manuel utilisateur

A.O. Smith

A.O. Smith Dura-Max AJH - 1000A - P Manuel utilisateur

Microline

Microline T.F.C.-4 Manuel

Eureka Forbes

Eureka Forbes Aquaguard Select Manuel utilisateur

Cetetherm

Cetetherm AquaEfficiency Manuel utilisateur

CB Tech

CB Tech CB-VOC Manuel utilisateur

Vaillant

Vaillant auroFLOW plus VPM 15 D Manuel utilisateur

resideo

resideo Braukmann HS10S Manuel utilisateur

Gude

Gude INOX 100/24 Manuel utilisateur

Mono

Mono Eco 1-60 Manuel

SpectraPure

SpectraPure Drinking Water Kit Manuel utilisateur

HydroCare

HydroCare Dual Action Manuel utilisateur

NEXT pool

NEXT pool STERILOR Cu/Ag Schéma de câblage

Alpha

Alpha SolarSmart 150 Guide de l'utilisateur

TA FRISTAR3 Manuel utilisateur

GÜDE

GÜDE HWA 800 K Manuel utilisateur

Rainfresh

Rainfresh UCS2 Manuel utilisateur