Stiga 110 Combi Pro Manuel utilisateur

STIGA PARK

2WD

110 Combi Pro

125 Combi Pro

8211-0546-03

1/3

24 Nm

ENGLISH EN

1 GENERAL

This symbol indicates WARNING. Seri-

ous personal injury and/or damage to

property may result if the instructions

are not followed carefully.

You must read these instructions for use

and the machine’s safety instructions

carefully.

1.1 Symbols

The following symbols appear on the machine.

They are there to remind you of the care and atten-

tion required in use.

This is what the symbols mean:

Warning!

Read the instruction manual and the safety

manual before using the machine.

Warning!

Do not insert your hands or feet under the

cover when the machine is in operation.

Warning!

Watch out for discarded objects. Keep on-

lookers away.

Warning!

Before starting repair work, remove the

spark plug cable from the spark plug.

1.2 References

1.2.1 Figures

The figures in these instructions for use are num-

bered 1, 2, 3, etc.

Components shown in the figures are marked A, B,

C, etc.

A reference to component E in figure 5 is written

“5:E”.

1.2.2 Headings

The headings in these instructions for use are num-

bered in accordance with the following example:

“2.3.2” is a subheading to “2.3” and is included un-

der this heading.

When referring to headings, only the number of the

heading is normally specified. E.g. “See 2.3.2”.

2 DESCRIPTION

2.1 General

The cutting deck is intended for use on Stiga’s 2-

wheel drive Park machines.

The cutting deck is supplied in one of the follow-

ing versions:

• With manual adjustment of cutting height.

• With electrical adjustment of cutting height.

2.2 Controls, 125 Combi Pro

2.2.1 Cutting height adjustment

The cutting height can be adjusted between 25 and

90 mm.

Electrical cutting height adjustment

The setting can be adjusted infinitely variably us-

ing a switch on the machine.

Manual cutting height adjustment

The setting can be adjusted to a number of fixed

positions using the lever. See fig. 1.

2.2.2 Incline forwards

The rear section of the cutting deck can be raised

12 mm by moving the two pins down one hole

from the basic setting. See fig. 2.

2.2.3 Rear mounting

The cutting deck’s rear section is secured with the

pins in fig. 2.

2.2.4 Mounting in implement lifter

The deck is mounted in the implement lifter with a

chain and snap hooks.

One snap hook is intended for the working position

and can be moved in the chain links to set the lift-

ing force.

The other snap hook is intended for the washing

position.

3 ASSEMBLY

3.1 Installing

1. Place the cutting deck in position in front of the

machine.

2. Install the deck mounts on the machine’s steer-

ing knuckles. See fig. 3.

3. Remove the pins and the washers on both sides.

See fig. 2.

4. Screw the arms into each other. See fig. 4.

5. Suspend the cutting deck in the implement lift-

er. See fig. 5.

6. If the deck has electrical cutting height adjust-

ment, connect the cable to the machine’s front

right socket. See fig. 7.

ENGLISH

3.2 Belt

The cutting deck’s rear section should rest on the

floor (it should not be lifted or secured).

Install the belt as follows:

1. Set the maximum cutting height.

2. Locate the belt around the machine’s belt pulley

(8:B).

3. Tension the belt with the belt idler (8:A)B. The

belt idler should be on the left side of the belt

viewed from the driver’s position.

4. Lift up and secure the rear section of the cutting

deck.

On machines with 17” wheels: Install the wash-

ers and the pins in the top hole. See fig. 2.

On machines with 16” wheels: Install the wash-

ers and the pins in the middle hole. See fig. 2.

3.3 Tyre pressure

Adjust the air pressure in the tyres as follows:

Front: 0.6 bar (9 psi).

Rear: 0.4 bar (6 psi).

4 USING THE MACHINE

Check that the grass that is to be cut is

completely free of foreign objects such

as stones etc.

4.1 Cutting height

The best cutting results are achieved when the

when the top third of the grass is cut off. I.e. 2/3 of

the length of the grass remains. See fig. 9.

If the grass is long and has to be cut significantly,

cut twice using different cutting heights.

Do not use the lowest cutting heights if the lawn

surface is uneven. This would entail a risk of the

blades being damaged against the surface and the

lawn’s top layer of soil being removed.

4.2 Incline

The cutting deck’s rear section can be lifted so that

the deck has a greater forward incline than that

provided by the basic setting. This incline affects

the cutting results as follows.

4.2.1 No incline

When the deck is in the basic setting, the best

mulching effect and good dispersion of the cut

grass are achieved. The basic setting is recom-

mended for normal grass.

4.2.2 Incline

When the cutting deck is inclined forwards, the

mulching effect is reduced while the cut grass is

dispersed better.

Inclining forwards is recommended for thicker

grass.

4.3 Mowing advice

In order to achieve optimum mowing results, fol-

low the advice below:

• Cut frequently.

• Run the engine at full throttle.

• The grass should be dry.

• Use sharp blades.

• Keep the underside of the cutting deck clean.

125 Combi Pro can cut the grass in the following

two ways:

• Mulching: composting and spreading.

• Rear ejection: ejects the grass in a line behind

the deck.

The deck is set for mulching on delivery. In order

to eject the grass in a line behind the deck, the plug

in fig. 6 must be removed.

Set the deck in service position (see 5.3) in order to

remove/install the plug.

5 MAINTENANCE

5.1 Preparation

All service and all maintenance must be carried out

on a stationary machine with the engine switched

off.

Prevent the machine from rolling by al-

ways applying the parking brake.

Stop the engine.

Prevent unintentional starting of the

engine by disconnecting the spark plug

cable from the spark plug and remov-

ing the ignition key.

5.2 Washing position

1. Activate the parking brake.

2. Set the implement lifter in transport position.

3. Set the highest cutting height.

4. Remove pins and washers. See fig. 2.

5. Grip the front edge of the deck and lift up. Hook

on the chain so that the deck is pointing diago-

nally upwards. See fig. 10.

It is absolutely forbidden to start the engine

when the deck is in the washing position.

Reset in accordance with 3.2, point 4.

ENGLISH EN

5.3 Service position

1. Activate the parking brake.

2. Set the implement lifter in transport position.

3. Set the highest cutting height.

4. If the deck has electrical cutting height adjust-

ment, disconnect the cable from the machine.

See fig. 7.

5. Remove pins and washers. See fig. 2.

6. Hook the belt idler arm on the mount (8:C)

7. Force the belt off the centre pulley (8:B).

8. Grip the front edge of the deck and lift up. Lift

until the deck is completely vertical and rest the

rear edge on the floor. See fig. 11.

Reset in accordance with 3.1.

5.4 Cleaning

The underside of the deck must be cleaned after

each use.

Set the deck in washing position.

Clean the underside of the deck carefully. Use a

high-pressure washer, scraper and/or brush.

When the surfaces are completely dry and clean,

touch up the paintwork. Use durable yellow paint

intended for metal outdoors.

5.5 Wheels

125 Combi Pro is fitted with two lubricating cups

(12:D) for the vertical shafts.

The grease nipples must be lubricated with univer-

sal grease after 50 hours of operation.

5.6 Replacing blades, fig. 13

Wear protective gloves when changing

blade(s) to avoid cutting yourself.

Check that the blades are always sharp.

This produces the best cutting results.

Always check the blade(s) after a collision. If the

blade system has been damaged, defective parts

should be replaced.

Always use genuine spare parts. Non-

genuine spare parts can entail a risk of

injury, even if they fit the machine.

The full blade is replaced when the edges

are worn.

Install the new blade with the punched text facing

down.

Tightening torque: 24 Nm

5.7 Wear protection

There are two wear protection devices on the un-

derside of the cutting deck to protect it. These can

be replaced if necessary.

6 SPARE PARTS

STIGA genuine spare parts and accessories are de-

signed specifically for STIGA machines. Please

note that ‘non-genuine’ spare parts and accessories

have not been checked or approved by STIGA:

The use of such parts and accessories

can affect the function and safety of the

machine. STIGA accepts no responsi-

bility for damage or injuries caused by

such products.

7 DESIGN REGISTRATION

This product or parts thereof is covered by the fol-

lowing design registration:

Sweden: 66 166

Germany: 499 11 740.9

France: 577 251-253, 577 439-443

USA: 435 564

GGP reserves the right to make alterations to the

product without prior notification.

www.stiga.com

GGP Sweden AB

Box 1006

SE-573 28 TRANÅS

Autres manuels pour 110 Combi Pro

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Stiga Tondeuse à gazon

Stiga

Stiga DECK PARK 107 M HD EL - 4WD Manuel utilisateur

Stiga

Stiga PARK 121 M Manuel utilisateur

Stiga

Stiga MP2 504 Series Manuel utilisateur

Stiga

Stiga CP1 434 Series Manuel utilisateur

Stiga

Stiga 420 Manuel utilisateur

Stiga

Stiga MP 84 Series Manuel utilisateur

Stiga

Stiga PLUS Manuel utilisateur

Stiga

Stiga CR 434 Series Manuel utilisateur

Stiga

Stiga MP1 504 Series Manuel utilisateur

Stiga

Stiga Autoclip 720S Manuel utilisateur

Stiga

Stiga READY 13-2715-16 Manuel utilisateur

Stiga

Stiga SRSA01 Manuel utilisateur

Stiga

Stiga TH 122 Series Manuel utilisateur

Stiga

Stiga GRASSLAND MOWER 53 CM Manuel utilisateur

Stiga

Stiga MJ 66 Manuel utilisateur

Stiga

Stiga COLLECTOR 45 COMBI EL Manuel utilisateur

Stiga

Stiga VILLA 107M Manuel utilisateur

Stiga

Stiga Park series Manuel utilisateur

Stiga

Stiga Cruiser 480 Li 80 series Manuel utilisateur

Stiga

Stiga FMC 112 Manuel utilisateur

Stiga

Stiga CP1 430 Li 48 series Manuel utilisateur

Stiga

Stiga Combi 53 S Manuel utilisateur

Stiga

Stiga 100C E Manuel utilisateur

Stiga

Stiga ZERO TURN MOWER 915333 Manuel utilisateur

Manuels Tondeuse à gazon populaires d'autres marques

RHINO

RHINO 1958 Manuel utilisateur

Wolf Garten

Wolf Garten Compact plus 40 B Manuel utilisateur

Cub Cadet

Cub Cadet LTX 1045 Manuel utilisateur

Craftsman

Craftsman 917.378461 Manuel utilisateur

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manuel utilisateur

Challenge

Challenge CH18V2 Instructions de fonctionnement

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manuel utilisateur

DEWEZE

DEWEZE ATM-725 Manuel d'utilisation

Weed Eater

Weed Eater 180083 Manuel utilisateur

Husqvarna

Husqvarna Poulan Pro PP185A42 Manuel utilisateur

Better Outdoor Products

Better Outdoor Products Quick Series Manuel utilisateur

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manuel d'utilisation

MTD

MTD 795, 792, 791, 790 Manuel utilisateur

Toro

Toro Groundsmaster 3505-D Manuel utilisateur

Dennis

Dennis FT 610 Manuel utilisateur

AIRFORCE

AIRFORCE F-15 Gen 3 Manuel utilisateur

MTD

MTD 126-220-000 Manuel utilisateur

Toro

Toro 74806 Manuel utilisateur