StarTech.com ICRS232BT1 Manuel utilisateur

Serial to Bluetooth Adapter

ICRS232BT1 Instruction Manual

Actual product may vary from photo

Serial (RS-232) to Bluetooth Class 1 Adapter

FFCCCCCCoommpplliiaanncceeSSttaatteemmeenntt

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

UUsseeooffTTrraaddeemmaarrkkss,,RReeggiisstteerreeddTTrraaddeemmaarrkkss,,aanndd

ootthheerrPPrrootteecctteeddNNaammeessaannddSSyymmbboollss

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and

do not represent an endorsement of a product or service by StarTech.com, or an

endorsement of the product(s) to which this manual applies by the third-party company in

question. Regardless of any direct acknowledgement elsewhere in the body of this

document, StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this

manual and related documents are the property of their respective holders.

TTaabblleeooffCCoonntteennttss

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Pairing with Windows XP SP2 embedded Bluetooth driver . . . . . . . . .2

Local Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Configuration: Role - Master or Slave . . . . . . . . . . . . . . .3

Remote MAC Address . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Configuration: Security . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Configuration: UART Configure . . . . . . . . . . . . . . . . . . . .4

Configuration: Adapter Name . . . . . . . . . . . . . . . . . . . . . .5

Automatic Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

More detail on initial baud rate setting . . . . . . . . . . . . . . .5

Remote Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Configuring the adapter following remote setup . . . . . . . .8

Configuration: Role - Master or Slave . . . . . . . . . . . . . . . .8

Configuration: Security . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Configuration: UART Configure . . . . . . . . . . . . . . . . . . . .8

Configuration: Adapter Name . . . . . . . . . . . . . . . . . . . . . .9

Automatic Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Instruction Manual

IInnttrroodduuccttiioonn

Thank you for purchasing a Bluetooth-to-Serial (RS-232 or RS-422/485) Adapter.

Featuring Bluetooth wireless technology, the serial adapter provides cable-free Serial

connections between your Bluetooth equipped PC and serial devices. This product is

compliant with Bluetooth v1.2 and allows you to wirelessly connect your computer and

RS-232 or RS-422/485 devices 100 meters apart.

FFeeaattuurreess

• Compliant with Bluetooth standard version 1.2

• Support for Microsoft Windows 98SE, Me, 2000, XP and 2003

• Operating distance of up to 100 meters in free space

• Bluetooth Class I (20 dbm)

• SPP profile supported

• Easy operation and setting up

BBeeffoorreeYYoouuBBeeggiinn

System Requirements

• Operating System: Windows 98SE, ME, 2000, XP or above

Mac OS 8.6 or above

• An available USB port (USB 1.1 or higher)

• A Bluetooth-enabled computer

Contents

This package should contain:

• USB to Serial Cable (1)

• Driver CD (1)

• User Manual (1)

Instruction Manual

IInnssttaallllaattiioonn

The following information explains how to configure the Bluetooth-to-Serial Adapter and

pair it with a Bluetooth host device. Please note that these instructions assume that a

second Bluetooth device is present, and attached to the PC with which you want the

Bluetooth-to-Serial Adapter to communicate. Please refer to the Accessories listed on

page 12 for compatible Bluetooth devices.

Pairing with Windows XP SP2 embedded Bluetooth driver

Prior to using the Bluetooth-to-Serial Adapter, configuration is required to pair the

devices to achieve an exclusive connection between them using the Bluetooth Address

and PIN code. Once the pairing process is complete and power has been added to the

device and PC with which it is communicating, the Bluetooth-to-Serial Adapter will

automatically attempt to link or be linked with another paired Bluetooth device wirelessly,

as if a cable were connecting the devices.

There are two ways to configure your Bluetooth-to-Serial Adapter: Local setup and

Remote setup.

Local Setup:

Local set up can be done by connecting a Bluetooth to Serial Adapter to your PC. You

can connect the PC COM port to a Bluetooth to Serial Adapter directly, or through an

RS-232 or RS-422/485 converter cable.

1. Connect the Bluetooth to Serial Adapter to your PC COM Port (e.g. COM1, COM2).

2. Insert the accompanying power adapter into the adapter port. Plug the remaining end

into an available power outlet.

3. Push the Mode Button until the MODE LED lights light up (yellow color), indicating that

the adapter is in Configuration Mode. In this mode, the Bluetooth to Serial Adapter is

working in Slave state waiting to be linked with other Bluetooth devices.

Instruction Manual

Mode

Button

Power Port

4. Insert the CD driver into the CD-ROM drive, and browse to X: \ Bluetooth \

BTRS232.exe, where Xis the designated CD-ROM drive. Double-click on the

BTRS232.exe file to begin configuration.

5. Select the PC COM Port to which the Bluetooth to Serial Adapter is connected.

If this is the first time you are configuring the Bluetooth to Serial Adapter, you can choose

the default Baud Rate : 115200. The local PC will use this baud rate to connect with your

Bluetooth to Serial Adapter.

6. Press the Connect Button on the adapter.

Please note: the connection will fail if the wrong COM port is connected or Baud Rate is

not set correctly.

Configuration:Role - Master or Slave (Default)

Depending on the applications, there are two states under which Bluetooth to Serial

Adapter can operate, while in DATA mode - Master and Slave. If you are using a USB

Bluetooth Dongle to pair with a Bluetooth to Serial adapter, then the Bluetooth to Serial

Adapter can be set to either Master or Slave state. If you are using two Bluetooth to

Serial Adapters paired together, one of them requires being set to Master and the other

needs to be set as Slave.

Master - Trying to link with other Bluetooth devices.

Slave - Waiting to be linked with other Bluetooth devices.

Master state :

If you choose this state, then you must enter the Bluetooth

MAC Address of the remote Bluetooth device (e.g.

000272463b86) with which this Bluetooth to Serial Adapter

will be paired and connected. Default is none.

Slave State (Default):

Discoverable (Default) - If Discoverable is enabled, the

Bluetooth to Serial Adapter can be found by searching for

Bluetooth Devices on the PC. If it is disabled, then it can

not be found. This feature will prevent other Bluetooth

hosts or devices from creating a link with it accidentally, if it

has previously been configured to pair with another device.

Instruction Manual

Remote MAC Address:

Enabling this feature allows you to enter the Bluetooth

MAC Address of the remote Bluetooth device

(e.g.000272463b86) to which the Bluetooth to Serial

Adapter will be linking. If it is disabled or MAC address is

left empty, any remote Bluetooth device can pair with the

Bluetooth to Serial Adapter. Once the necessary changes

have been made, please click the Save button, followed by

Yes and OK on the following screens respectively.

Please note: Be sure to click the Save button in each

modification parameter, or settings will be lost.

Configuration: Security

Secure Connection (Default PIN = 1234). Disabling this

function will allow other Bluetooth devices to connect with

this Bluetooth to Serial Adapter without confirming a PIN

code. If it is enabled, then you should enter a PIN code

(length <=12 digits). By default this feature is enabled and

the PIN code is 1234.

PIN stands for Personal Identification Number. Enter the

PIN code, keeping it the same as the remote Bluetooth

device, so the two devices can be paired together.

Once you have made your selection, please click on the

Save button.

Configuration: UART Configure

Change UART parameters, Bluetooth to Serial Adapter

will use them to connect with a RS-232 or RS-422/485

device later.

Baud Rate: 9600 ~ 460800 (Default 115200)

Stop Bit: One/Two (Default One)

Parity Bit: None/Odd/Even (Default None)

Following selection, please press the Save Button.

Please note : Maximum Baud Rate: 460.8 Kbps.

Instruction Manual

Configuration: Adapter Name

Enter a Device Name for your Bluetooth to Serial Adapter

(length <= 31 alphanumeric characters). For example:

“Bluetooth to Serial Adapter”.

Once you have entered this information, please press the

Save Button, followed by the Disconnect button.

Automatic Connection:

Remove your Bluetooth to Serial Adapter from the PC COM port, and connect it to your

RS-232 or RS-422/485 device.

Push the MODE button to change from Configuration mode to DATA mode. The MODE

LED will turn off.

Following this, automatic connection will begin. If configured in the Master state, the

Bluetooth to Serial Adapter will scan its proximity for a Bluetooth device that has the

matching MAC address and PIN code. If found, it will establish the wireless link

automatically and the Bluetooth LED (blue color) on the adapter will become illuminated.

If configured in the Slave state, the Bluetooth to Serial Adapter will wait for another

Bluetooth device to create a link with it.

More Detail on Initial Baud Rate Setting

1)When power is applied to the Bluetooth to Serial Adapter, it will try to link (Master) or

be linked (Slave) with another Bluetooth device with a matching MAC address or PIN

code and build a link between them. If another Bluetooth device cannot be found

(e.g. its power is turned off), the initial baud rate of the Bluetooth to Serial Adapter

will be set to 115200 (default).

If you forgot any previous settings for the Bluetooth to Serial Adapter, and want to

reconfigure it, simply turn off the power of the other Bluetooth devices, and power on

your Bluetooth to Serial Adapter individually. Because it is impossible for your

Bluetooth to Serial Adapter to establish a link with its paired Bluetooth device (it is

turned off), the baud rate of the Bluetooth to Serial Adapter will default to 115200.

You can then use 115200 baud to connect the Adapter with your PC, then change its

settings accordingly.

2)When power is applied to a Bluetooth to Serial Adapter and the paired Bluetooth

device is found and automatic connection has been made between them, the BLUE

Bluetooth LED on the Bluetooth to Serial Adapter will light up, and the baud rate of the

Bluetooth to Serial Adapter will be the value which was previously input in UART

Configure in the previous section.

When the BLUE Bluetooth LED is illuminated on the Adapter, and you want to local

set up your Bluetooth to Serial Adapter after entering into Configuration mode (both

Instruction Manual

blue and yellow LEDs illuminated), you must remember the baud rate and use it to

connect with the COM port previously selected.

3)When power is applied to the Bluetooth to Serial Adapter, and a new baud rate is

entered and saved under UART Configure and then push MODE button to get into

DATA mode, push the MODE button again to enter into Configuration mode, where the

baud rate will be the one most recently entered.

RReemmootteeSSeettuupp

This setup can be used when you connect the Bluetooth to Serial Adapter remotely to an

RS232 device (e.g. a Modem), and you want to configure using a local PC. The local PC

will require a USB Bluetooth Dongle as well as the required driver installation. The

following illustrates a remote setup with Microsoft Windows XP SP2 embedded Bluetooth

drivers. Before using remote setup, be sure to pair the Bluetooth to Serial Adapter and

USB Bluetooth Dongle successfully.

Please note: If you are using Widcomm or IVT Bluetooth drivers, the following pairing

steps will be different from the software you used. Although the steps are different, you

still can follow these instructions to start the same functions on your Bluetooth software.

1. Please insert your USB Bluetooth

Dongle into an available PC USB

Port. Windows will install the

drivers automatically.

2. Enter the control panel and double-

click the Bluetooth Devices icon.

3. Push the MODE button. The

MODE LED (yellow color) will light.

Please click Add to search for the

Bluetooth device to which the

Adapter is connected.

Please note : The Bluetooth to Serial Adapter can

easily be found if it is configured in DATA/Slave mode,

however it will not be found in DATA/Master mode.

4. When the Add Bluetooth Device Wizard launches,

please select My device is set up and ready to be

found. Click Next to continue.

5. The Windows Bluetooth Device Wizard will find

the Bluetooth to Serial Adapter. Please select the

new device, and click Next to continue.

Instruction Manual

6. You will be asked to input the Bluetooth to Serial

Adapter PIN code. If this is the first time the adapter

is being configured, the PIN code is set to factory

default as “1234”. As such, enter “1234” in this step.

If the PIN code was previously configured, the

most recent PIN code must be entered. Click Next to

continue.

Please note: If your PIN code is not correct, the

Bluetooth devices will not pair together. Bluetooth to

Serial Adapter default PIN code is “1234”. If you had

modified it before and forgot the PIN code, please reset

your Bluetooth to Serial Adapter and follow the

aforementioned steps to configure the PIN code.

7. Windows will then verify your PIN code. If the PIN code is

correct, the Bluetooth to Serial Adapter and USB Bluetooth

Dongle will pair together, and the Bluetooth LED (Blue color)

will become illuminated. Click Finish to complete pairing.

8. To determine the COM port to which the Adapter is assigned,

please select the COM Ports tab

Please note : If you want to check the Bluetooth to Serial

Adapter MAC address, you can click the Bluetooth to Serial

Adapter and select the Hardware tab. Click on Properties to

display the MAC Address.

9.To locate the USB Bluetooth Dongle MAC address:

Select Generic Bluetooth Radio device on the Hardware

tab, and click Properties as shown in the picture on the right.

The Generic Bluetooth Radio Properties page will pop up.

Click on the Advanced button, to display the USB Bluetooth

Dongle MAC address

Instruction Manual

Table des matières

Autres manuels StarTech.com Adaptateur

StarTech.com

StarTech.com 8STDKT30CHPD Manuel utilisateur

StarTech.com

StarTech.com USB32HD4 Manuel utilisateur

StarTech.com

StarTech.com PEXESAT32 Manuel utilisateur

StarTech.com

StarTech.com TBT3TBTADAP Manuel utilisateur

StarTech.com

StarTech.com 8ST102BUSBCMULTIP Manuel utilisateur

StarTech.com

StarTech.com USB32VGAPRO Manuel utilisateur

StarTech.com

StarTech.com DKT31CHPDL Manuel utilisateur

StarTech.com

StarTech.com SSPMSVESA Manuel utilisateur

StarTech.com

StarTech.com ICUSB422 Manuel utilisateur

StarTech.com

StarTech.com 104B-USBC-MULTIPORT Manuel utilisateur

StarTech.com

StarTech.com USB External Sound Card Adapter Manuel utilisateur

StarTech.com

StarTech.com PEXM2SAT32N1 Manuel utilisateur

StarTech.com

StarTech.com USBA-BLUETOOTH-V5-C2 Manuel utilisateur

StarTech.com

StarTech.com US1GC30SFP Manuel utilisateur

StarTech.com

StarTech.com CDP2HD4K60SA Manuel utilisateur

StarTech.com

StarTech.com IDE44 Manuel de référence

StarTech.com

StarTech.com ST2000PEXPSE Manuel utilisateur

StarTech.com

StarTech.com PEX300WN2X2 Manuel utilisateur

StarTech.com

StarTech.com PCI100MMSC Manuel utilisateur

StarTech.com

StarTech.com IP2DVI Manuel utilisateur

StarTech.com

StarTech.com USBBT1EDR2 Manuel utilisateur

StarTech.com

StarTech.com USB867WAC22 Manuel utilisateur

StarTech.com

StarTech.com PEX2S552B Manuel utilisateur

StarTech.com

StarTech.com ICUSB2321FIS Manuel utilisateur

Manuels Adaptateur populaires d'autres marques

PCB Piezotronics

PCB Piezotronics 090B274 Manuel utilisateur

Auvidea

Auvidea J20 Manuel du produit

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuel utilisateur

Akribis

Akribis ITF-21-BISS-MIT Manuel utilisateur

Tenda

Tenda W54U Manuel utilisateur

ROHO

ROHO AGILITY Manuel utilisateur

PROLiNK

PROLiNK WN2001 Manuel utilisateur

Hawking

Hawking HUF2 Manuel utilisateur

Airlink101

Airlink101 AWLC4030 Manuel utilisateur

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuel utilisateur

Philips

Philips SWA4554S/10 Manuel utilisateur

JVC

JVC TS-C9D2B Manuel d'instructions

NETGEAR

NETGEAR A6100 Manuel utilisateur

D-Link

D-Link DWA-121 Manuel utilisateur

Philips

Philips SWA2037 Manuel utilisateur

Basalte

Basalte 0610-20 Manuel utilisateur

Yealink

Yealink EHS40 Manuel utilisateur

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuel utilisateur