Star Trac 728-0006 Manuel
LCD Attachment
Installation and
Service Manual
2
1
Table of Contents
Parts List ................................................................................................2
Hardware Kits ........................................................................................3
Bike, Cross Trainer and Stepper Start ....................................................4
Steps in Assembling the Bracket ............................................................5
Installation Instructions (Bike, Cross Trainer & Stepper) .......................6
Installation Instructions (Bike, Cross Trainer & Stepper) Cont’d ............7
Installation Instructions (Bike, Cross Trainer & Stepper) Cont’d ............8
Installation Instructions (Bike, Cross Trainer & Stepper) Cont’d ............9
Final Installation (Bike, Cross Trainer & Stepper) .................................10
Treadmill Start ......................................................................................11
Steps in Assembling the Bracket ..........................................................12
Treadmill Installation Instructions .......................................................13
Treadmill Installation Instructions (Cont’d) .........................................14
Treadmill Installation Instructions (Cont’d) .........................................15
Treadmill Installation Instructions (Cont’d) .........................................16
Treadmill Installation Instructions (Cont’d) .........................................17
Final Installation (Treadmill) .................................................................18
Maintenance Requirements ..................................................................19
Club Owner Guide ................................................................................20
Club Owner Guide (Cont’d) ..................................................................21
A/V Installer’s Guide .............................................................................22
A/V Installer’s Guide (Cont’d) ..............................................................23
A/V Installer’s Guide (Cont’d) ..............................................................24
A/V Installer’s Guide (Cont’d) ..............................................................25
A/V Installer’s Guide (Cont’d) ..............................................................26
A/V Install - Wire Management ............................................................27
2
2
All Kits include:
Before installing the TV bracket verify that you have the proper kit according to the list above and that all the
parts are included. If any of the items are missing call StarTrac at 800-503-1221 to order a replacement kit.
Parts List (All Machines)
Product Model ...................................................................................Kit Part Number
Pro Tread .......................................................................................................715-3628
Pro Stepper ....................................................................................................711-3178
Pro Bike Upright .............................................................................................718-5079
Pro Bike Recumbent ......................................................................................720-0087
CrossTrainer ...................................................................................................721-1093
Neck Mounting support assembly
(Crossbow)
Mounting braces
(Wings)
Monitor Interface
(Gooseneck)
Clamp top and bottom with pad Wire management
*Not included in kit 715-3628 (Pro Tread)
3
3
Hardware Kits
Kit No.728-0005 (Hardware Kit for Bikes, Stepper and CrossTrainer)
Kit No.728-0006 (Hardware Kit for Pro Treadmills)
4
Bike, CrossTrainer and Stepper
5
5
Steps in Assembling the Bracket
Bike, CrossTrainer and Stepper
This pictorial view shows the assembly of the TV bracket in. The following
pages describe the install process.
(Final assembled bracket)
6
6
Installation Instructions
Tools required for Bike, CrossTrainer, and Stepper (not supplied):
• 5mm or 3/16” Allen wrench (Crossbow and clamp screws)
• 1/8” or 3mm Allen wrench (Neck screws)
• #2 Phillips Screwdriver (Wing screws)
• 7/16” or 11MM open end wrench (Cross bow screws)
Bike, CrossTrainer and Stepper
1
Remove the four screws from the display.
(Screws are no longer needed)
2
Attach the wings into the back of the display using
the Phillips head screws.
NOTE: The longer screws go in the 2 bottom
holes and the shorter screws in the 2 top holes.
Failure to follow this will result in damage to the
display.
Align the wings on the crossbow so the curved edge
is facing the inside and the smooth edge on the
outside as shown in the diagram.
7
7
Installation Instructions (Cont’d)
Bike, CrossTrainer and Stepper
3
- Attach the crossbow to the wings.
- Tighten the two nuts with the 7/16” or 11MM open
end wrench as shown.
4
Slide the top mounting plate on the neck and align the
top plate notch with the neck base notch.
Make sure top plate sits fl ush on the notch.
8
8
Installation Instructions (Cont’d)
Bike, CrossTrainer and Stepper
5
NOTE: Before tightening, make sure
base of bracket neck is flush with
fitness product.
NO YES
5
- Insert the rubber pad onto the bottom mounting plate
and attach the plate around the neck of the product.
- Using the remaining 4 screws, attach the bottom and
top mounting plates together.
- Check fit and alignment and make any necessary
adjustments, tighten all the screws securely.
Continued
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Star Trac Support et étagère
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
