Stanley NEOBOLT COLLAR CROPPER Manuel utilisateur
USER MANUAL
NEOBOLT COLLAR CROPPER
NEOBOLT COLLAR CROPPER
1
ENGLISH
CONTENT
1. Safety..............................................................................................................................................................2
2. Technical specications.................................................................................................................................2
3. Package contents:..........................................................................................................................................2
4. Cutter setup: ..................................................................................................................................................3
5. Cutter use ....................................................................................................................................................... 4
6. Tool disassembly...........................................................................................................................................5
7. Tool assembly.................................................................................................................................................6
8. Tool maintenance ..........................................................................................................................................7
2
ENGLISH
NEOBOLT COLLAR CROPPER
1. SAFETY
• Before use, read and understand safety and operating instructions both the hydraulic equipment and the
collar cropper tool.
• Always use eye protection when using this tool.
• Use of protective gloves is recommended.
• Avoid placing hands in potential pinch points, as tool will move while cutting.
• Verify that equipment is in good working condition and properly set up before using.
2. TECHNICAL SPECIFICATIONS
Neobolt size
3/8” 12mm 12mm/ 1/2” 1/2” 5/8”
Cropper Assembly 65120-00061 65120-00060 65110-00059 65110-00054 65110-00055
Use with Avdel AV5 Huck SF20 Avdel AV30 Avdel AV15 Avdel AV30
Hydraulic pressure (bar) Alum: 190
Seel: 490 400 180 400 350
Cropper Stroke (mm) 30 50 41 32 41
Cropper weight (kg) 0.48 0.86 2.4 1 1.5
Cropper Dia/Length (mm) 27 / 108 38 / 71 60 / 150 43 / 98 48 / 118
3. PACKAGE CONTENTS
One Neobolt collar cropper assembly.
3
ENGLISH
Neobolt cropper components:
Neobolt size
65120-00061 65120-00060 65110-00059 65110-00054 65110-00055
Item Quantity 3/8” 12mm 12mm/ 1/2” 1/2” 5/8”
O-ring* 1 1 6510-00463 65110-00460 65110-00431 65110-00431 65110-00432
Jaw* 2 6 65110-00327 65110-00213 65110-00171 65110-00171 65110-00309
Cutter* 3 1 65110-00326 65110-00211 65110-00452 65110-00167 65110-00311
Jaw holder 4 1 65110-00328 65110-00212 65110-00451 65110-00172 65110-00310
Nut 5 1 65110-00329 - 65110-0454 65110-00291 65110-00313
Nose Hsg 6 1 65110-00330 - 65110-00453 65110-00173 65110-00312
* Typical wear items
4. CUTTER SETUP
Set pump to required pressure (See section 2 for required pressure)
Connect tool to hydraulic pump, use extension hose if required.
Mount cutter into hydraulic tool (See section 2 for tool selection)
• Remove o-ring from front of hydraulic tool.
• Thread cutter clockwise (hand tight – Do not use wrench) into tool rod, until it bottoms out.
4
ENGLISH
• Thread retaining nut clockwise into tool body (hand tight – Do not use wrench), until it bottoms out.
• Cycle tool twice and retighten retaining nut if needed.
• Verify that pintail from Neobolt pin ts inside the jaws.
• Tool is now ready to use.
5. CUTTER USE
• Verify that pump pressure has been set to desired value
• Check tool to verify that jaws are intact and free of debris. Also check cutting surfaces for damage.
5
ENGLISH
• Place tool against fastener to be cut. Pin tail must be fully inserted into cutter. Tool must be aligned with
the fastener to be removed.
OK INCORRECT
• Press trigger to start cutting. Release button once collar is fully cut.
• Remove tool from fastener.
• Separate collar from pin to remove fastener.
6. TOOL DISASSEMBLY
• Unthread nose housing from cutter.
• Push jaw holder into cutter and slide out of the cutter. Jaws should fall out of cutter.
6
ENGLISH
7. TOOL ASSEMBLY
• Slide o-ring into jaw holder as shown.
• Apply light coat of moly-lithium grease to inside of cutter.
• Place jaws into jaw holder as shown, keeping them aligned with side grooves.
• Insert jaws and jaw holder into cutter, until jaws emerge out of the other side of cutter.
7
ENGLISH
• Slide retaining nut into nose housing and thread nose housing (hand tight – Do not use wrench) into
cutter.
8. TOOL MAINTENANCE
For optimal performance, it is critical that the tool is kept clean and in good working order.
Cleaning frequency will depend on usage and operating conditions.
To clean tool:
• Disassemble tool.
• Clean components. Inspect for damage and replace any damaged components.
• Apply alight coat of moly-lithium grease to inside of cutter using acotton swab.
• Reassemble tool.
8
ENGLISH
STANLEY Engineered Fastening
4 Shelter Rock Lane
Danbury, Connecticut,
United States, 06810
Tel. 877 364 2781
Fax 800 225 5614
Holding your world together®
Find your closest STANLEY Engineered Fastening location on
www.stanleyEngineeredFastening.com/contact
For an authorized distributor nearby please check
www.stanleyEngineeredFastening.com/econtact/distributors
© 2020 Stanley Black & Decker, Inc.
Avdel®, Avex®, Avibulb®, Avinox®, Avseal®, Bulbex®, Hemlok®, Interlock®, Klamp-Tite®, Monobolt®, POP®,
ProSet®, Stavex®and T-Lok®are registered trademarks of Stanley Black & Decker, Inc. and its aliates. The names and
logos of other companies mentioned herein may be trademarks of their respective owners. Data shown is subject
to change without prior notice as a result of continuous product development and improvement policy. Your local
STANLEY Engineered Fastening representative is at your disposal should you need to conrm latest information.
Manual Number Issue C/N
65124-00007 A 20242
Table des matières
Autres manuels Stanley Outils électriques
Stanley
Stanley FATMAX SFMCE520 Manuel utilisateur
Stanley
Stanley FATMAX FMES550 Manuel utilisateur
Stanley
Stanley FATMAX SFMCE100B Manuel utilisateur
Stanley
Stanley TT46 Manuel utilisateur
Stanley
Stanley 150704XSTN Manuel utilisateur
Stanley
Stanley WS10 Manuel utilisateur
Stanley
Stanley PROSET PB3400 Manuel utilisateur
Stanley
Stanley FATMAX FMC011S2 Manuel utilisateur
Stanley
Stanley STRR1200 Manuel utilisateur
Stanley
Stanley SB25PT-05 Manuel utilisateur
Stanley
Stanley SXH1530 Manuel utilisateur
Stanley
Stanley SDR1400 Manuel utilisateur
Stanley
Stanley FATMAX V20 LITHIUM ION SBW920 Manuel utilisateur
Stanley
Stanley Fat max Manuel utilisateur
Stanley
Stanley WS10 Mode d’emploi
Stanley
Stanley FATMAX FMC041 Manuel utilisateur
Stanley
Stanley FATMAX V20 SFMCD715 Manuel utilisateur
Stanley
Stanley 73200 Guide de dépannage
Stanley
Stanley Fatmax FME670 Manuel utilisateur
Stanley
Stanley 76001 Manuel utilisateur
