Standard Horizon Matrix GX2000 Manuel utilisateur

Page 1GX2000S/GX2100S

MATRIX GX2000/GX2100

25 Watt VHF/FM

Marine Transceiver

Owner's Manual

GX2000/GX2100Page 2

QUICK REFERENCE GUIDE I

You can do the basic operation in numerical order of the illustration below.

[PTT]S

WITCH

Speak into the

microphone in a

normal voice level

while pressing this

switch.

[TT

T]/ [SS

S]K

Selects the operating

channel.

[H/L]B

UTTON

When pressed,

toggles the transmit

power between High

(25W) and Low (1W).

[SQL]K

NOB

Move this control

clockwise to squelch

or counter clockwise

un-squelch the radio.

[PWR/VOL]K

NOB

Press and hold this knob until the LCD

turns on, and adjust the audio level.

[CH]K

NOB

Selects the operating channel.

[16/9]B

UTTON

yPress to recall chan-

nel 16.

yPress and hold to

recall channel 9.

[16/9]B

UTTON

yPress to recall

channel 16.

yPress and hold to

recall channel 9.

ICROPHON

Page 3GX2000/GX2100

[DISTRESS]B

UTTON

Note: for this key to

operate a MMSI must

be programmed.

Lift the red cover,

press the Distress but-

ton once, then press

and hold until the ra-

dio alarms.

QUICK REFERENCE GUIDE II

[CALL/MENU]B

UTTON

yPress to access the

“DSC MENU”.

yPress and hold to

access the “SETUP

MENU”.

[CH]K

NOB

ySelect the operating

channel.

ySelect the item in

the “SETUP MENU”

and “DSC MENU”.

yWhen the “SETUP

MENU” or “DSC

MENU” is selected,

pressing this knob

saves a selection.

[CLR/WX]B

UTTON

yPress to cancel the

menu selection.

yPress and hold to

recall the last-used

NOAA Weather

Channel.

ROGRAMMABLE

These three keys

functions can be cus-

tomized by the Setup

Menu mode.

The factory defaults

are [PA/FOG], [IC],

and [SCAN]key.

[AIS]B

UTTON

Press to change the

display to AIS (Auto-

matic Identification

System) mode

GX2000/GX2100Page 4

QUICK INSTALLATION GUIDE I

DESKTOP MOUNTING OVERHEAD MOUNTING

DESKTOP/OVERHEAD MOUNTING THE RADIO

The supplied universal mounting bracket allows desktop or overhead nounting.

Use a 13/64” (5.2-mm) bit to drill the holes to a surface which is more 0.4 inch

(10 mm) thick and can support more than 3.3 lbs (1.5 kg) and secure the

bracket with the supplied screws, spring washers, flat washers, and nuts.

ELECTRICAL CONNECTIONS

GPS Receiver

Plotter ConnectionRadio Wires

External Speaker

Green

Purple

Red Black

NMEA OUT

NMEA COMMON

NMEA IN

( )

Blue

Shield

White

12 V Battery

Page 5GX2000/GX2100

QUICK INSTALLATION GUIDE II

FLUSH MOUNTING

Bracket

Adjusting Screw

Lock-washer nut combination

FLUSH MOUNTING THE RADIO

The optional MMB-84 Flush-Mount Bracket allows flush mounting the radio to

your vessel.

1. To assist in flush mounting, a template has been included. Use this tem-

plate to assess the mounting location.

2. Use the template to mark the location where the rectangular hole is to be

cut. Confirm the space behind the dash or panel is deep enough to accom-

modate the transceiver (at least 6.7 inches or 17 cm deep).

There should be at least 1/2 inch (1.3 cm) between the transceiver’s heatsink

and any wiring, cables or structures.

3. Cut out the rectangular hole and insert the transceiver.

4. Fasten the brackets to the sides of the transceiver with the lock washer nut

combination; so that the mounting screw base faces the mounting surface.

5. Turn the adjusting screw to adjust the tension so that the transceiver is

tight against the mounting surface.

GX2000/GX2100Page 6

1 GENERAL INFORMATION

1.1 INTRODUCTION

The STANDARD HORIZON GX2000/2100 is a VHF/FM Marine Transceiver

designed for use in the frequency range of 156.025 to 163.275 MHz. The

GX2000/2100 can be operated from 11 to 16 VDC and has a switchable RF

output power of 1 watt or 25 watts.

The GX2100 is equipped with the AIS (Automatic Identification System) re-

ceiver and its display program which enables to identify and avoid other large

vessels nearby your vessel. The GX2100 is equipped with the display pro-

gram of the AIS too. Threrfore, the GX2000 also enables to identify and avoid

other large vessels nearby your vessel, if the AIS receiver (not supply) is

commected.

The GX2000/GX2100 is capable of DSC (Digital Selective Calling) Class D

operation and an Enhanced second station RAM+ mic (CMP30 remote-con-

trol speaker/microphone with display) or VH-310 Handset. Class D operation

allows continuous receiving of Digital Selective Calling functions on channel

70 even if the radio is receiving a call.

The GX2000/GX2100 operates on all currently-allocated marine channels

which are switchable for use with USA, International, or Canadian regulations.

It has an emergency channel 16 which can be immediately selected from any

channel by pressing the red [16/9]key. NOAA Weather channels can also be

accessed immediately by Press and holding the [CLR(WX)] key with channel

selection.

Other features of the GX2000/GX2100 include: 30W PA/Fog, multi-station

intercom, scanning, priority scanning, submersible speaker mic, high and low

voltage warning, and GPS repeatability.

2 PACKING LIST

When the package containing the transceiver is first opened, please check it

for the following contents:

yGX2000 or GX2100 Transceiver

yMounting Bracket and attaching hardware

yOwner’s Manual

yWarning Sticker

yPower Cord

Page 7GX2000/GX2100

3 OPTIONS

MMB-84 .........................................................................Flush-Mount Bracket

CMP30B/W ............... Remote-Access Microphone (RAM+ Mic, Black/White)

VH-310 .................................................. Remote Handset (available in Black)

CT-100 ............................................... 23-foot Extension Cable for RAM+ Mic

CVS2500 ...............................................................................Voice Scrambler

MLS-310 .............. 10W amplified External Speaker with on/off Volum control

MLS-300 ...................................................................... External Loudspeaker

101W ............................................................... Mini White Extension Speaker

220SW ..................................................................... 4.5” Round Hail/PA Horn

240SW ........................................................ 5” x 8” Rectangular Hail/PA Horn

MEK-4 .... Microphone Extension Kit (to remote front panel mic to rear panel)

4 SAFETY / WARNING INFORMATION

This radio is restricted to occupational use, work related operations only where

the radio operator must have the knowledge to control the exposure condi-

tions of its passengers and bystanders by maintaining the minimum separa-

tion distance of 0.89 m (2.92 feet). Failure to observe these restrictions will

result in exceeding the FCC RF exposure limits.

Antenna Installation:

The antenna must be located at least 0.89 m (2.92 feet) away from passen-

gers in order to comply with the FCC RF exposure requirements.

Lithium Battery Included:

This radio contains a Lithium Battery. At the end of radio’s useful life, under

various state and lows, it may be illegal to dispose of Lithium Battery into the

municipal waste stream. Check with your local solid waste officials for details

in your area for recycling options or proper disposal.

ON-LINE WARRANTY REGISTRATION

Please visit www.standardhorizon.com to register the GX2000/

GX2100 Marine VHF. It should be noted that visiting the Web site from

time to time may be beneficial to you, as new products are released

they will appear on the STANDARD HORIZON Web site.

PRODUCT SUPPORT INQUIRIES

If you have any questions or comments regarding the use of the

GX2000/GX2100, you can visit the STANDARD HORIZON Web site

to send an E-Mail or contact the Product Support team at 800-767-2450

M-F 7:00-5:00PST.

GX2000/GX2100Page 8

5 FCC RADIO LICENSE INFORMATION

Standard Horizon radios comply with the Federal Communication Commis-

sion (FCC) requirements that regulate the Maritime Radio Service.

5.1 STATION LICENSE

An FCC ship station license is no longer required for any vessel traveling in

U.S. waters (except Hawaii) which is under 20 meters in length. However, any

vessel required to carry a marine radio on an international voyage, carrying a

HF single side band radiotelephone or marine satellite terminal is required to

have a ship station license. FCC license forms, including applications for ship

(605) and land station licenses can be downloaded via the Internet at http://

www.fcc.gov/Forms/Form605/605.html. To obtain a form from the FCC, call

(888) 225-5322.

5.2 RADIO CALL SIGN

Currently the FCC does not require recreational boaters to have a Ship Radio

Station License. The USCG recommends the boats registration number and

the state to be used.

5.3 CANADIAN SHIP STATION LICENSING

You may need a license when traveling in Canada. If you do need a license

contact their nearest field office or regional office or write:

Industry Canada

Radio Regulatory Branch

Attn: DOSP

300 Slater Street

Ottawa, Ontario

Canada, KIA 0C8

5.4 FCC / INDUSTRY CANADA INFORMATION

The following data pertaining to the transceiver is necessary to fill out the li-

cense application.

Type Acceptance ......................................................................... FCC Part 80

Output Power ...............................................1 Watt (low) and 25 Watts (high)

Emission ......................................................................... 16K0G3E, 16K0G2B

Frequency Range .................................................... 156.025 to 163.275 MHz

FCC Type Number ................................................................... K6630443X3D

Industry Canada Type Approval ............................................ 511B-30443X3S

Page 9GX2000/GX2100

6 FCC NOTICE

NOTICE

Unauthorized changes or modifications to this equipment may void com-

pliance with FCC Rules. Any change or modification must be approved

in writing by STANDARD HORIZON.

NOTICE

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to ra-

dio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be de-

termined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equpmet into an outlet on a circuit different from that to

which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

GX2000/GX2100Page 10

7 GETTING STARTED

7.1 ABOUT VHF RADIO

The radio frequencies used in the VHF marine band lie between 156 and 158

MHz with some shore stations available between 161 and 163 MHz. The ma-

rine VHF band provides communications over distances that are essentially

“line of sight” (VHF signals do not travel well through objects such as buildings,

hills or trees). Actual transmission range depends much more on antenna type,

gain and height than on the power output of the transmitter. On a fixed mount

25W radio transmission expected distances can be greater than 15 miles, for

a portable 5W radio transmission the expected distance can be greater than 5

miles in “line of sight”.

7.2 SELECTING AN ANTENNA

Marine antennas are made to radiate signals equally in all horizontal direc-

tions, but not straight up. The objective of a marine antenna is to enhance the

signal toward the horizon. The degree to which this is accomplished is called

the antenna’s gain. It is measured in decibels (dB) and is one of the major

factors in choosing an antenna. In terms of effective radiated power (ERP),

antennas are rated on the basis of how much gain they have over a theoretical

antenna with zero gain. A 3 foot, 3dB gain antenna represents twice as much

gain over the imaginary antenna.

Typically a 3 foot 3dB gain stainless steel whip is used on a sailboat mast. The

longer 8 foot 6dB fiberglass whip is primarily used on power boats that require

the additional gain.

Autres manuels pour Matrix GX2000

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Standard Horizon Émetteur-récepteur

Standard Horizon

Standard Horizon HX851 Manuel utilisateur

Standard Horizon

Standard Horizon HX270E Manuel utilisateur

Standard Horizon

Standard Horizon HX400 Manuel utilisateur

Standard Horizon

Standard Horizon Eclipes DSC GX1000S Manuel utilisateur

Standard Horizon

Standard Horizon ECLIPSE DSC+ GX1200E Manuel utilisateur

Standard Horizon

Standard Horizon Eclipse DSC+ GX1100S Manuel utilisateur

Standard Horizon

Standard Horizon HX270S Manuel utilisateur

Standard Horizon

Standard Horizon HX270S Manuel utilisateur

Standard Horizon

Standard Horizon HX760S Manuel utilisateur

Standard Horizon

Standard Horizon HX870 Manuel utilisateur

Standard Horizon

Standard Horizon HX851 Manuel utilisateur

Standard Horizon

Standard Horizon HX290 Manuel utilisateur

Standard Horizon

Standard Horizon HX380 Manuel utilisateur

Standard Horizon

Standard Horizon HX210 Manuel utilisateur

Standard Horizon

Standard Horizon HX320E Manuel utilisateur

Standard Horizon

Standard Horizon Hx750s Manuel utilisateur

Standard Horizon

Standard Horizon Intrepid LE GX1265S Manuel utilisateur

Standard Horizon

Standard Horizon 30063X30 Manuel utilisateur

Standard Horizon

Standard Horizon HX890 Manuel utilisateur

Standard Horizon

Standard Horizon GX2400GPS Manuel utilisateur

Standard Horizon

Standard Horizon QUANTUM GX6500E Manuel utilisateur

Standard Horizon

Standard Horizon Matrix GX2000 Manuel utilisateur

Standard Horizon

Standard Horizon HX400 Manuel utilisateur

Standard Horizon

Standard Horizon HX600S Manuel utilisateur

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Kenwood

Kenwood ProTalk TK-3201 Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Kenwood

Kenwood TK-3180 Manuel d'utilisation et d'entretien

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Kenwood

Kenwood TK-2217 Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Kenwood

Kenwood TS-590SG Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur