Standard Horizon HX760S Manuel utilisateur

FCC ID:K6630323X30

IC:511B-30323X30

Vertex Standard Co.,Ltd.1

HX760S Operating Manual

Congratulations on your purchase of the HX760S! Whether this is your first portable marine VHF

transceiver, or if you have other STANDARD HORIZON equipment, the STANDARD HORIZON

organization is committed to ensuring your enjoyment of this high performance transceiver, which

should provide you with many years of satisfying communications even in the harshest of

environments. STANDARD HORIZON technical support personnel stands behind every product

sold, and we invite you to contact us should you require technical advice or assistance.

We appreciate your purchase of the HX760S, and encourage you to read this manual thoroughly, so

as to learn and fully understand the capabilities of the HX760S.

NOTE

Water resistance of the transceiver is assured only when the battery pack is attached to the

transceiver and MIC/SP cap is installed in the MIC/SP jack.

WARNING

This radio is capable of transmitting on Marine VHF.

The FCC allows the use of VHF Marine band on water areas only. However the FCC does not

allow the use of the VHF Marine band when on land. If persons use the VHF Marine Band on

land and interfere with others communicating, the FCC will be notified and search for the

interference. Responsible parties found to be transmitting on the VHF Marine Band on land could

be fined up to $10,000 for the first offense.

RF EXPOSURE SAFETY STATEMENT

SAFETY INFORMATION

Your wireless handheld portable transceiver contains a low power transmitter. When the

Push-to-Talk (PTT) button is pushed, the transceiver sends out radio frequency (RF) signals. In

August 1996, the Federal Communications Commission adopted RF exposure guidelines with

safety levels for hand-held wireless devices.

This device is authorized to operate at a duty factor not to exceed 50% (this corresponds to 50%

transmission time and 50% reception time).

WARNING: To maintain compliance with the FCC’s RF exposure guidelines, this transmitter and

its antenna must maintain a separation distance of at least 1 inch (2.5 centimeters) from your face.

Speak in a normal voice, with the antenna pointed up and away from the face at the required

separation distance.

If you use a headset accessory for this radio, with the radio worn on your body, use only the

Vertex Standard belt clip for this transceiver, and ensure that the antenna is at least 1 inch (2.5

centimeters) from your body when transmitting.

Use only the supplied antenna. Unauthorized antennas, modifications, or attachments could

damage the transmitter, and may violate FCC regulations.

FCC AND CANADA RADIO LICENSE INFORMATION

Standard Horizon radios comply with the Federal Communication Commission (FCC) and

FCC ID:K6630323X30

IC:511B-30323X30

Vertex Standard Co.,Ltd.2

Industry-Canada requirements that regulate the Maritime Radio Service.

MARITIME STATION LICENSE

An FCC ship station license is no longer required for any vessel traveling in U.S. waters which uses

a VHF marine radio, RADAR or EPIRB, and which is not required to carry radio equipment.

However, any vessel required to carry a marine radio on an international voyage, carrying a HF

single side band radiotelephone or marine satellite terminal. FCC license forms, including

applications for ship (506) and land station licenses can be downloaded via the Internet at

www.fcc.gov/forms. To obtain a form from the FCC, call (888) 225-5322.

MARINE RADIO CALL SIGN

Currently the FCC does not require recreational boaters to have a Ship Radio Station License. The

USCG recommends the boats registration number and the state to be used.

CANADIAN SHIP STATION LICENSING

You may need a license when traveling in Canada. If you do need a license contact their nearest field

office or regional office or write:

Industry Canada

Radio Regulatory Branch

Attn: DOSP

300 Slater Street

Ottawa, Ontario

Canada, KIA 0C8

FCC/INDUSTRY CANADA INFORMATON

The following data pertaining to the transceiver is necessary to fill out the license application.

FCC Type Accepted: Part 80

Output Power with FNB-V99LI: 1.0/2.5/5.0/6.0 W (Low/Mid/High/Nor)

Emission: 16K0G3E

Frequency Range: 156.025 to 163.275MHz

FCC Type Number: K6630323X30

Industry Canada Type Approval: 511B-30323X30

FCC NOTICE

Unauthorized changes or modifications to this equipment may void compliance with FCC Rules.

FCC ID:K6630323X30

IC:511B-30323X30

Vertex Standard Co.,Ltd.3

Any change or modification must be approved in writing by STANDARD HORIZON, a Marine

Division of VERTEX STANDARD.

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

・ Increase the separation between the equipment and receiver.

・ Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

・ Consult the dealer or an experienced marine electronics technician for help.

1. GENERAL INFORMATION

1.1 INTRODUCTION

The HX760S is a SUBMERSIBLE FLOATING 6-Watt portable two way marine transceiver. The

transceiver has all allocated USA, International, or Canadian channels. It has emergency channel 16

which can be immediately selected from any channel by pressing the [16/9] key. NOAA (National

Oceanic and Atmospheric Administration) Weather channels can also be accessed immediately by

pressing the [WX] key.

The HX760S includes the following features: Memory Scanning, Priority Scanning, NOAA Weather

Alert, Battery Saver, easy-to-read large LCD display, EEPROM memory back-up, Battery Life

displayed on LCD, and a transmit Time-Out Timer (TOT).

The HX760S transmitter provides a full 6 Watt of transmit power and is selectable to 5, 2.5, and 1

Watt to assist the user in ensuring maximum battery life.

In addition, the HX760S can communicate your voice and receiving signal between the optional

BH-2 Bluetooth®Head Set and the transceiver, with the Bluetooth®technology.

The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and

any use of such marks by Vertex Standard Co., Lit. is under license.

2. ACCESSORIES

2.1 PACKING LIST

When the package containing the transceiver is first opened, please check it for the following

contents:

・ HX760S Transceiver

FCC ID:K6630323X30

IC:511B-30323X30

Vertex Standard Co.,Ltd.4

・ CAT460 Antenna

・ FNB-V99LI 7.4 V, 1150 mAh LI-ion Battery Pack

・ CD-39 Charger Cradle for HX760S

・ NC-88B 120VAC Wall Charger for CD-39

・ E-DC-19A DC Cable with 12 V Cigarette Lighter Plug for CD-39

・ CLIP-19 Belt Clip

・ Owner’s Manual

2.2 OPTIONS

・ MH-73A4B Speaker/Microphone

・ MH-57A4B Mini Speaker/Microphone

・ VC-24 VOX Headset

・ VC-27 Earpiece/Microphone

・ CD-39 Charger Cradle

・ FNB-V99LI 7.4 V, 1150 mAh LI-ion Battery Pack

・ FBA-38 Alkaline Battery Case

・ E-DC-19A DC Cable with 12 V Cigarette Lighter Plug

・ NC-88B/C/UÚ230-240 VAC Wall Charger for the FNB-V99LI

・ E-DC-6 DC Cable; plug and wire only

・ CN-3 Radio-to-Ship’s-Antenna Adapter

Ú: “B” suffix is for use with 120 VAC, “C” suffix is for use with 230-240 VAC, and “U” suffix is

for use with 230 VAC.

Note: Before operating the HX760S for the first time, it is recommended that the battery be charged.

Please see section “4.1.4 USING THE CD-39 CHARGER CRADLE” for details.

3. ABOUT THIS RADIO

3.1 ABOUT THE VHF MARINE BAND WARNING

The radio frequencies used in the VHF marine band lie between 156 and 158 MHz with NOAA

Weather stations available between 161 and 163 MHz. The marine VHF band provides

communications over distances that are essentially “Line of sight” Actual transmission range

depends much more on antenna type, gain and height than on the power output of the transmitter.

On a fixed mount 25 W radio transmission expected distances can be greater than 15 miles, for a

portable 6 W radio transmission the expected distance can be greater than 5 miles in “Line of

sight”.

The user of a Marine VHF radio is subject to severe fines if the radio is used on land. The

reasoning for this is you may be near an inland waterway, or propagation anomalies may cause

your transmission to be heard in a waterway. If this occurs, depending upon the marine VHF

channel on which you are transmitting, you could interfere with a search and rescue case, or

FCC ID:K6630323X30

IC:511B-30323X30

Vertex Standard Co.,Ltd.5

contribute to a collision between passing ships. For VHF Marine channel assignments refer to

page 26 section 11.

4. GETTING STARTED

If the radio has never been used, or its charge is depleted, it may be charged by connecting the

CD-39 Charger Cradle with the NC-88 battery charger, as shown in the illustration. If 12V DC

power is available, the optional E-DC-19A DC Cable with 12 V Cigarette Lighter Plug or the

optional E-DC-6 DC Cable may be used for charging the battery. The NC-88, E-DC-19A, and

E-DC-6 will charge a completely discharged FNB-V99LI battery pack in about 8 hours.

4.1 BATTERIES AND CHARGERS

The FNB-V99LI is a high performance LI-ion battery providing high capacity in a compact package.

CAUTION

To avoid risk of explosion and injury, FNB-V99LI battery pack should only be removed, charged

or recharged in non-hazardous environments.

4.1.1 BATTERY SAFETY

Battery packs for your transceiver contain LI-ion batteries. This type of battery stores a charge

powerful enough to be dangerous if misused or abused, especially when removed from the

transceiver. Please observe the following precautions:

DO NOT SHORT BATTERY PACK TERMINALS: Shorting the terminals that power the

transceiver can cause sparks, severe overheating, burns, and battery cell damage. If the short is of

sufficient duration, it is possible to melt battery components. Do not place a loose battery pack on or

near metal surfaces or objects such as paper clips, keys, tools, etc. When the battery pack is installed

on the transceiver, the terminals that transfer current to the transceiver are not exposed. The

terminals that are exposed on the battery pack when it is mounted on the transceiver are charging

terminals only and do not constitute a hazard.

DO NOT INCINERATE: Do not dispose of any battery in a fire or incinerator. The heat of fire may

cause battery cells to explode and/or release dangerous gases.

Battery Maintenance

For safe and proper battery use, please observe the following:

・ Battery packs should be charged only in non-hazardous environments;

・ Use only STANDARD HORIZON-approved batteries;

・ Use only a STANDARD HORIZON, (a Marine Division of VERTEX STANDARD) approved

charger. The use of any other charger may cause permanent damage to the battery.

・ Follow charging instructions provided with the chargers.

・ Keep the battery contacts clean.

FCC ID:K6630323X30

IC:511B-30323X30

Vertex Standard Co.,Ltd.6

Battery Storage

Store the batteries in a cool place to maximize storage life. Since batteries are subject to

self-discharge, avoid high storage temperatures that cause large self-discharge rates. After extended

storage, a full recharge is recommended.

Battery Recycling

DO NOT PLACE USED BATTERIES IN YOUR REGULAR TRASH!

LI-ION BATTERIES MUST BE COLLECTED, RECYCLED OR DISPOSED OF IN AN

ENVIRONMENTALLY SOUND MANNER.

The incineration, land filling or mixing of LI-ion batteries with the municipal solid waste stream is

PROHIBITED BY LAW in most areas.

Return batteries to an approved LI-ion battery recycler. This may be where you purchased the

battery.

Contact your local waste management officials for other information regarding the environmentally

sound collection, recycling and disposal of LI-ion batteries.

4.1.2 BATTERY INSTALLATION/REMOVAL

1. To install the battery pack, insert the battery pack into the battery rest on the bottom of the

transceiver, then turn the Battery Pack Lock to the “LOCK” position with a coin.

2. To remove the battery pack, turn the transceiver off, open the Battery Pack Lock on the bottom

of the transceiver, then slide out the battery from the transceiver.

NOTE

The battery lock must be set to “LOCK” position to ensure water integrity and from the battery

coming loose.

4.1.3 BATTERY CHARGING

1. Turn the transceiver off.

2. Insert the DC plug from the NC-88 into the DC jack on the CD-39 rear panel, then plug the

NC-88 into the AC line outlet.

3. Insert the HX760S (with the battery pack) into the CD-39; the antenna should be at the left side

when viewing the charger from the front.

4. If the HX760S is inserted correctly, the Red “CHARGING” indicator will glow. A

fully-discharged pack will be charged completely in approximately 8 hours.

5. When charging is completed, the red LED indicator will change to green.

CAUTION

The CD-39 is NOT designed to be waterproof. Do not attempt to charge in water hazardous

locations.

NOTE

The CD-39 is only designed for the charging of the HX850S’ battery, and is not suitable for other

FCC ID:K6630323X30

IC:511B-30323X30

Vertex Standard Co.,Ltd.7

purposes. The CD-39 may contribute noise to TV and radio reception in the immediate vicinity,

so we do not recommend its use adjacent to such device.

5. CONTROLS AND INDICATORS

5.1 CONTROLS AND SWITCHES NOTE

This section defines each control of the transceiver. For detailed operating instructions, refer to

section “6 BASIC OPERATION” Refer to illustrations for the location of the following controls,

switches, and connections.

1. ANT Jack (Top Panel)

The supplied CAT460 flexible antenna is attached here.

2. MIC/SP Jack (Top Panel)

The jack accepts the optional MH-73A4B Speaker/Microphone, MH-57A4B Mini

Speaker/Microphone, VC-24 VOX Headset, or VC-27 Earpiece/Microphone. When this jack is

used, the internal speaker and microphone are disabled.

3. PTT (PUSH-TO-TALK) Switch

When pushed activates the transmitter.

4. Keypad

[VOL] Key

Press this key to activate the volume adjusting mode. Press the [S] or [T] key to adjust the

receiver audio volume level.

[SQL] Key

Press this key to activate the squelch adjusting mode. Press the [S] or [T] key to adjust the

squelch threshold level.

Press and hold this key for 3 seconds to open the squelch, allowing you to monitor the

operating channel. Release the key to resume normal (quiet) monitoring.

[S(UP)] Key

This key is used to change the operating channel, receiver volume level, and squelch threshold

level.

Press the key momentarily, the channel (or level) increases one step. Holding the key, the

channel (or level) increases continuously.

[T(DOWN)] Key

This key is used to change the operating channel, receiver volume level, and squelch threshold

level.

Press the key momentarily, the channel (or level) decreases one step. Holding the key, the

channel (or level) decreases continuously.

FCC ID:K6630323X30

IC:511B-30323X30

Vertex Standard Co.,Ltd.8

[WX] Key

Immediately recalls the last-used NOAA (National Oceanic and Atmospheric Administration)

Weather Channel from any channel location. Recalls the previously- selected working channel

when the [WX] key is pressed again.

Secondary use:

When the [16/9] key is held and the [WX] key is pressed, the radio will change the marine band

between the USA, International, and Canadian channels.

[SCAN(DW)] Key

Starts scanning and priority scanning of programmed channels. When scanning, press and hold

this key to turn on and off priority scan ("P" icon is shown on the bottom left side of the display

during Priority scanning).

[H/L(LOCK)] Key

Press this key to toggle the transmitter output power between “Normal” (6 Watts), “High” (5

Watts), “Medium” (2.5 Watts), and “Low” (1 Watt) power. This key does not function on the

“Transmission Inhibited” and “Low power only” channels.

Secondary use:

Hold down this key to lock the keypad (except the PTT, [VOL], [SQL], [POWER], and

[H/L(LOCK)] keys) so that they are not accidentally changed. The “KEY” icon will appear at

the bottom right corner on the display, to indicate that the functions are locked. Hold down this

key until the “KEY” icon disappears to unlock the radio.

[16/9] Key

Pressing this key immediately recalls channel 16 from any channel location. Holding down this

key recalls channel 9. Pressing this key again reverts to the previous selected working channel.

[MEM] Key

Press this key to memorize the selected channel for scanning. When pressed a “MEM” icon will

be shown on the LCD display indicating the channel has been saved to scan memory. The scan

memory is only used with the Marine and WX channels.

To delete the channel from scan memory, select the channel and press this key until “MEM” is

removed from the display.

Secondary use:

To enable the SOS Strobe light, turn off radio, press and hold this key while turning on. To turn

off strobe light, turn radio off and back on.

[POWER] Key

Press and hold this orange key for three seconds to toggle the transceiver’s power on and off.

[PRESET] Key

Immediately recalls one of up to 10 user preset memories for each band (shown as “0” - “9” on

FCC ID:K6630323X30

IC:511B-30323X30

Vertex Standard Co.,Ltd.9

the LCD). Pressing this key repeatedly scrolls through the preset memory channels.

5. TX/BUSY Indicator

This indicator glows green when a signal is being received and red when transmitting. When

the Emergency feature is activated, this indicator blinks the internationally-recognized Morse

Code “S.O.S” message.

6. Thermo Sensor

To measure a water temperature, soak this point in water several minutes.

NOTE

It may take a few minutes for the temperature register correctly.

NOTE

The temperature sensor may not display the correct temperature when the temperature of the

radios inside is high; for example, while the transmission mode or high receiver audio output.

7. Microphone

The internal microphone is located here.

8. Speaker

The internal speaker is located here.

9. Battery Pack Lock (Bottom side)

Turn the Battery Pack Lock to the “OPEN” position for battery removal.

5.2 INDICATORS

1. Information Bar

The temperature or battery voltage indicates here.

2. “H”/“M”/“L” Indicators

“H” indicates High power (5 Watts); “M” indicates Medium power (2.5 Watts); and “L” is for

Low power (1 Watt). “Blank” in this location indicates Normal power (6 Watts).

3. VOL Indicator

This indicator shows the receiver audio volume level.

4. SQL Indicator

This indicator shows the squelch level.

5. “SCN” Indicator

This indicator appears when the Scan is activated.

6. “DW” Indicator

This indicator appears when the Dual Watch is activated.

7. “P” Indicator

This indicator shows the channel is in the “Priority Channel”.

8. USA/INTL/CAN Indicator

These indicators show the “band” of operation for the particular channel. “USA” indicates the

FCC ID:K6630323X30

IC:511B-30323X30

Vertex Standard Co.,Ltd.10

USAband; “INTL” indicates the International band; and “CAN” indicates the Canadian band.

9. “TX” Indicator

This indicator appears during transmission.

10. “WX” Indicator

This indicator appears when a NOAA weather channel is selected.

11. “MEM” Indicator

This indicator shows the channel is in the transceiver’s “Scan Memory”.

12. Channel Display

The operating channel is shown on the LCD in both the transmission and reception modes.

13. Battery Indicator

When the battery charge is almost depleted, a “BATTERY” icon will appear on the display.

When this icon appears, it is recommended that you charge the battery soon.

14. “KEY” Indicator

When the “KEY” icon is shown on the LCD, all keys are disabled except for the PTT, [VOL],

[SQL], [POWER], and [H/L(Lock)] keys.

6. BASIC OPERATION

6.1 PROHIBITED COMMUNICATIONS

The FCC prohibits the following communications:

・ False distress or emergency messages:

・ Messages to “any boat” except in emergencies and radio tests;

・ Messages to or from a vessel on land;

・ Transmission while on land;

・ Obscene, indecent, or profane language (potential fine of $10,000).

6.2 INITIAL SETUP

1. Install the battery pack on the transceiver (see section “5.1.2 BATTERY

INSTALLATION/REMOVAL”).

2. Install the antenna onto the transceiver; hold the bottom end of the antenna, the screw it onto

the mating connector on the transceiver until it is snug. Do not over-tighten.

NOTE

Water resistance of the transceiver is assured only when the battery pack is attached to the

transceiver and MIC/SP cap is installed in the MIC/SP jack.

6.3 RECEPTION

1. Press and hold the [POWER] key for two seconds to turn the transceiver on. The DC supply

Autres manuels pour HX760S

Table des matières

Autres manuels Standard Horizon Émetteur-récepteur

Standard Horizon

Standard Horizon INTREPID + GX1270S Manuel utilisateur

Standard Horizon

Standard Horizon HX850S Manuel utilisateur

Standard Horizon

Standard Horizon ECLIPSE + GX1250SA Manuel utilisateur

Standard Horizon

Standard Horizon Eclipes DSC GX1000S Manuel utilisateur

Standard Horizon

Standard Horizon HX471S Manuel utilisateur

Standard Horizon

Standard Horizon HX40 Mode d’emploi

Standard Horizon

Standard Horizon Intrepid LE GX1265S Manuel utilisateur

Standard Horizon

Standard Horizon MATRIX Series Manuel utilisateur

Standard Horizon

Standard Horizon HX210 Manuel utilisateur

Standard Horizon

Standard Horizon HX600S Manuel utilisateur

Standard Horizon

Standard Horizon GX2400GPS Manuel utilisateur

Standard Horizon

Standard Horizon HX600S Manuel utilisateur

Standard Horizon

Standard Horizon HX751 Manuel utilisateur

Standard Horizon

Standard Horizon Quantum GX5000S Manuel utilisateur

Standard Horizon

Standard Horizon 30063X30 Manuel utilisateur

Standard Horizon

Standard Horizon HX370SAS Manuel utilisateur

Standard Horizon

Standard Horizon HX870E Manuel utilisateur

Standard Horizon

Standard Horizon Eclipse DSC+ GX1200 Manuel utilisateur

Standard Horizon

Standard Horizon QUEST-X GX1500E Manuel utilisateur

Standard Horizon

Standard Horizon HX300 Manuel utilisateur

Standard Horizon

Standard Horizon PHANTOM Series PS2000 Manuel utilisateur

Standard Horizon

Standard Horizon HX300 Manuel utilisateur

Standard Horizon

Standard Horizon QUEST+ GX1256S Manuel utilisateur

Standard Horizon

Standard Horizon HX851 Manuel utilisateur

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Kenwood

Kenwood ProTalk TK-3201 Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Kenwood

Kenwood TK-3180 Manuel d'utilisation et d'entretien

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Kenwood

Kenwood TK-2217 Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Kenwood

Kenwood TS-590SG Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur