Stagg HEADBANGER10 MK3 Manuel utilisateur

USER

MANUAL

HEADBANGER10

MK3

SLI MHW HB10

Table of Contents

1.BEFORE USAGE

This package contains

Unpacking

Introduction

Specifications

Features

2.INSTALLATION

Installation requirements

Power Connection

DMX Serial Data Link

3. OPERATION

Menu Map

Operating Instructions

DMX Channels

1. BEFORE USAGE

This package contains

•1x HeadBanger 10 MK3

•1x Power Cable

•1x User Manual

Unpacking

•Thank you for purchasing this product, it has been thoroughly tested

and has been shipped in perfect operating condition.

•Carefully check the packaging for damage that may have occurred during

shipping.

•If the packaging appears to be damaged, carefully inspect your fixture

for any damage and be sure all equipment necessary to operate the unit has

arrived intact.

•If damage has been found or parts are missing, please contact your vendor or

our customer support number for further instructions.

Introduction

•This fixture can operate in six different operating modes: DMX control, sound

active, automatic, manual setup, infrared remote control or in a Master/Slave

configuration

•This product comes with several built-in programs that can be used while

operating as a single unit or with multiple units linked in a master/slave

configuration

•For best results use fog or special effects smoke to enhance the beam

projection

•Warning! To prevent or reduce the risk of electrical shock or fire, do not

expose this unit to rain or moisture

•Warning! This product may cause severe eye damage. Avoid looking

directly into the light source at all times!

Specifications

•Voltage: AC100V～240V, 50-60Hz

•Power Consumption: 80W

•Light source: 7x 10W RGBW 4 in 1 LED

•Beam angle: 25°

•Max output @1m: 6100 Lux

•PAN 540°, Tilt 270° with 16bit control

•DMX channels: 9 or 14 DMX Channels

•Packing Dimensions: 210x210x140mm

•Net weight: 2,75 Kg

Features

•3PIN XLR DMX in and out

•IEC power in

•4 control modes: DMX512, automatic programs, sound control, master/slave

•LCD display for easy setup

•Indoor operation temperature range: -20°C～+40°C

•Dimmer: 0-100%

•Strobe 0-10Hz

Please Note: Specifications and improvements in the design of this unit and this

manual are subject to change without any prior written notice.

2. INSTALLATION

Installation requirements

•The product can be hung or placed on a solid surface

•If you install the light in a hanging position, always use a suitable mounting

position and a clamp or screw that is strong enough to hold the product

without stress. Always use a safety wire to secure the light.

•Always keep a distance of minimum 0.5 m (1.6 ft.) to all objects or persons

•Installation should always be done by a trained professional.

•Make sure the light always has good ventilation

•It is recommended to always use 110 Ohm DMX cable to prevent data

corruption of your DMX control signal

Power connection

The equipment has an auto-switching power supply that can accommodate a

wide range of input voltages. The only thing necessary to do before powering on

the unit is to make sure the line voltage you are applying is within the range of

accepted voltages. This equipment will accommodate between 100V and 240v

AC 50-60HZ. It is possible to daisy chain the power connection from one fixture

to the next. We recommend not connecting more than 30 fixtures on one 16A

220V socket and not more than 15 fixtures on one 16A 110V socket.

Color

Connection

Brown

AC live wire

Blue

AC zero curve

Green/Yellow

AC ground wire

DMX Serial Data Link

1. Connect the male 3pin DMX input of the first fixture to the female 3pin DMX

output of the lighting controller using 110 Ohm DMX cable, for example a Stagg

Commandor 10 (skip this step when not using a controller)

2. Connect the output of the first fixture to the input of the next fixture using 110

Ohm DMX cable. Repeat this process until you reach your last fixture. Here it is

recommended to connect a DMX terminator to the output of the last fixture in the

chain.

3. OPERATION

Menu Map

Dxxx

DMXAddress

001-512

MAFA

Slow automatic mode

SLOU

Fast automatic mode

FASt

Master sound mode

MStS

Stand-Alone Control

MStc

Slave mode

SlAu

PAN

PAN normal mode

PAN

PAN reverse mode

rPAN

TIL

TILT normal mode

TIl

TILT reverse mode

rTIl

dIS

Normal display Mode

dIS

Reversed display

rdIS

14CH

14 channels mode

14CH

9 channels mode

9CH

PA54

Max pan rotation 540°

PA54

Max pan rotation 360°

PA36

Max pan rotation 180°

PA18

TI27

Max tilt rotation 270°

TI27

Max tilt rotation 180°

TI18

Max tilt rotation 90°

TI09

REST

Reset device

REST

LOAD

Load factory setting

LOAD

DMX daisy-chain example

Operating Instructions

Take note: All changes made to the unit become active and saved when pressing

the “OK” button. Screen turn automatically off after 5 seconds of inactivity. The

unit will then display the active running mode or the DMX address when DMX

input is detected.

DMX Address Setup

•

Press MENU, until “Dxxx” is displayed, then press ENTER

•Change the DMX address by pressing UP or DOWN

•Press ENTER to save the DMX address

Modes Selection

•Press MENU, then UP or DOWN until one of the following mode is displayed,

then press ENTER

oMASL / SLOU: Master automatic slow mode. The HeadBanger

will play automatic sequences with slow movements.

oMAFA / FASt: Master automatic fast mode. The HeadBanger will

play automatic sequences with fast movements.

oMStS: Master sound mode. The HeadBanger will play automatic

sequences controlled by the ambient sound or music.

oMStc: Machine Stand-alone Control. Second automatic mode to

use the HeadBanger as stand-alone machine without any slaves

in the daisy-chain

oSlAu: Slave mode. This unit will follow the “Master” behavior of

the daisy chain.

•Select your desired mode with UP or DOWN and press ENTER to confirm.

Tilt and pan reverse mode

•Press MENU, then UP or DOWN until “Pan” or “TIL” is displayed, then press

ENTER.

•"rPan" or “rTIL”: The unit inverts the pan (horizontal) or tilt (vertical) movement

(up becomes down and left becomes right)

•"Pan" or “TIL”: The unit's PAN movement is run normally.

•Press ENTER to confirm

Display Inversion

•Press MENU, then UP or DOWN until “DISP” or “rDIS” is displayed, then

press ENTER

•By pressing ENTER, the unit's display can be inverted so that when the light

is hung upside-down, the display will still be properly readable by the user.

Channels modes

•Press MENU, then UP or DOWN until “14CH” or “9CH” is displayed, then

press ENTER

•You can choose between 9 or 14 dmx channels modes using the UP or

DOWN buttons, press ENTER to confirm.

9 Channels

Channel

function

0-255

Pan

0-255

Tilt

0-7

8-134

135-239

240-255

None

Dimmer

Strobe

Full on

0-255

Movements Speed

150-200

Reset

14 Channels

Channel

Function

0-255

Pan

0-255

Pan fine

0-255

Tilt

0-255

Tilt fine

0-255

Movements speed

0-7

8-134

135-239

240-255

None

Dimmer

Strobe

Full on

0-255

0-7

8-21

22-34

35-49

Color1

Color2

Color3

Color4

50-63

64-77

78-91

92-105

106-119

120-134

135-147

148-161

162-175

176-189

190-203

204-217

218-231

232-255

Color5

Color6

Color7

Color8

Color9

Color10

Color11

Color12

Color13

Color14

Color15

Color16

Color17

Color Jump change

0-255

Speed

0-7

8-22

23-37

38-53

54-67

68-82

83-97

98-112

113-127

128-142

143-157

158-172

173-187

188-202

203-217

218-232

233-255

No function

Auto 1

Auto 2

Auto 3

Auto 4

Auto 5

Auto 6

Auto 7

Auto 8

Sound 1

Sound 2

Sound 3

Sound 4

Sound 5

Sound 6

Sound 7

Sound 8

150-255

Reset

Max PAN Rotation Setup

•Press MENU, then Up or DOWN until “PAxx“ is displayed, then press ENTER

•You can reduce the maximum horizontal rotation range to 540° (PA54), 360°

(PA36) or 180° (PA18) using the UP or DOWN buttons, press ENTER to

confirm.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Stagg Équipement d'éclairage

Stagg

Stagg HYPERNOVA SDJ-HYPERNOV1 Manuel utilisateur

Stagg

Stagg KINGPAR 1 Manuel utilisateur

Stagg

Stagg HEAD BANGER 10 SLI MHW HB10 Manuel utilisateur

Stagg

Stagg Ecopar 630 31 Manuel utilisateur

Stagg

Stagg FlatPar 4 Manuel utilisateur

Stagg

Stagg SLI-MHBHH10 Manuel utilisateur

Stagg

Stagg TRITON SDJ-TRITON Manuel utilisateur

Stagg

Stagg HeadHunter10 SLI-MHBHH10 Manuel utilisateur

Stagg

Stagg TAGGER 30 Manuel utilisateur

Stagg

Stagg Hyperion 5R Manuel utilisateur

Stagg

Stagg HEADBANGERXT SLI MHW HBXT Manuel utilisateur

Stagg

Stagg Truss34 Manuel utilisateur

Stagg

Stagg EcoParXS Manuel utilisateur

Stagg

Stagg EcoPar6 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur