SSV Embedded Systems IGW/936-L Manuel utilisateur

LTE Router

IGW/9

with

eSOM/3517

First Steps

SSV Embedded Systems

Dünenweg 5

D-30419 Hannover

Phone: +49 (0)511/40 000-0

Fax: +49 (0)511/40 000-40

Emai : sa [email protected]

Document Revision: 1.4

Date: 2018-08-29

LTE Router IGW/936-L – First Steps

D oc u m e n t R e v i s i o n 1 . 4

CONTENT

INTRODUCTION ............................................................................................................... 3

1.1

Checklist ................................................................................................................................. 3

1.2

Conventions ........................................................................................................................... 3

SAFETY GUIDELINES ..................................................................................................... 4

REQUIRED EQUIP ENT ................................................................................................. 5

SI CARD ......................................................................................................................... 6

CONNECTIONS ................................................................................................................ 7

5.1

LTE Antenna ........................................................................................................................... 7

5.2

Ethernet Link .......................................................................................................................... 8

5.3

Serial Ports COM2 and COM3 ................................................................................................

5.4

Power Supply ....................................................................................................................... 10

OPERATION ................................................................................................................... 11

6.1

Booting the IGW/ 36-L ........................................................................................................ 11

6.2

Accessing the SSV/WebUI .................................................................................................... 11

6.3

Accessing the SSV/WebUI with DHCP enabled ................................................................... 12

6.4

LTE Modem Configuration ................................................................................................... 14

6.5

WAN Configuration .............................................................................................................. 15

6.6

Firewall Configuration ......................................................................................................... 16

6.7

LAN1 Configuration .............................................................................................................. 17

6.8

LAN2 Configuration .............................................................................................................. 18

Access via Telnet .................................................................................................................. 1

6.10

Access via FTP ...................................................................................................................... 20

TECHNICAL DATA ......................................................................................................... 22

PINOUT SCREW TER INALS ....................................................................................... 22

LED FUNCTIONS ........................................................................................................... 23

TROUBLE SHOOTING IP ADDRESS PROBLE S ....................................................... 24

HELPFUL LITERATURE ................................................................................................ 25

CONTACT ............................................................................................................................. 25

DOCU ENT HISTORY ......................................................................................................... 25

LTE Router IGW/936-L – First Steps

D o c u m e n t R e v i s i o n 1 . 4

1 INTRODUCTION

This documentation gives you an overview about the initial operation and the first steps of

use with the LTE Router IGW/9 6-L.

1.1 Checklist

Compare the content of your IGW/9 6-L start-up package with the checklist below.

If any item is missing or appears to be damaged, please contact SSV!

 LTE Router IGW/9 6-L

 1x LTE antenna

 Adapter cable with power and RS2 2 connector

 Plug-in power supply

 Screwdriver

 Documentation

 CD-ROM for eSOM/ 517

IMPORTANT!

You will need further equipment to operate the IGW/9 6-L! Please refer to chap-

ter 3.

1.2 Conventions

Convention

Usage

bold

Important

terms

monospace

Filenames,

Pathnames, program code, command lines

Table 1: Conventions used in this docu ent

LTE Router IGW/936-L – First Steps

D o c u m e n t R e v i s i o n 1 . 4

2 SAFETY GUIDELINES

Please read the following safety guidelines carefully! In case of property or personal

da age by not paying attention to this anual and/or by incorrect handling, we do not

assu e liability. In such cases any warranty clai expires.

• The power supply should be in immediate proximity to the device.

• The power supply must provide a stable output voltage between 11 – 28 VDC. The out-

put power should be at least 2.5 W.

• Please pay attention that the power cord or other cables are not squeezed or damaged

in any way when you set up the device.

• Do NOT turn on the power supply while connecting any cables, especially the power

cables. This could cause damaged device components! First connect the cables and

THEN turn the power supply on.

• The installation of the device should be done only by qualified personnel.

• Discharge yourself electrostatic before you work with the device, e.g. by touching a

heater of metal, to avoid damages.

• Stay grounded while working with the device to avoid damage through electrostatic

discharge.

• The case of the device should be opened only by qualified personnel.

LTE Router IGW/936-L – First Steps

D o c u m e n t R e v i s i o n 1 . 4

3 REQUIRED EQUIPMENT

To operate the IGW/9 6-L the following hardware is required:

• a valid SIM card with an appropriate mobile tariff. Please refer to chapter 4 to see how

the SIM card is inserted.

• one Ethernet cross-over cable or two Ethernet patch cables and a switch.

To configure the IGW/9 6-L a PC with the following features is required:

• Windows 7 or higher

• Web browser (e.g. Firefox, Chrome)

• Telnet/SSH client (e.g. TeraTerm)

• FTP client (e.g. FileZilla)

• 10/100 Mbps Ethernet network controller and TCP/IP configuration

• CD-ROM drive

LTE Router IGW/936-L – First Steps

D o c u m e n t R e v i s i o n 1 . 4

4 SIM CARD

The internal SIM card of the IGW/9 6-L can be changed through the slot on the backside.

To insert the SIM card just push it by hand as deep as possible into the slot.

Please note:

Pay attention to the correct orientation of the SIM card like shown in fig. 1!

Then use a screw driver to push it gently further into the slot until you here a soft "click".

Figure 1: Inserting the SIM card

To remove the SIM card just push it gently with a screw driver until you hear a soft "click"

(see fig. 2). The SIM card is ejected a few millimeters and can be pulled out easily by hand.

Figure 2: Re oving the SIM card

LTE Router IGW/936-L – First Steps

D o c u m e n t R e v i s i o n 1 . 4

5 CONNECTIONS

For a quick and easy start with the IGW/9 6-L there are a few cable connections necessary.

The following chapters describe how these connections have to be made.

5.1 LTE Antenna

Connect the LTE antenna with the IGW/9 6-L like shown in fig. 3 and place it where the LTE

signal strength is high.

Figure 3: Connecting the LTE antenna

Please note:

The best LTE signal strength is achieved by using two antennas. Please contact SSV if

you want to order a second LTE antenna.

LTE Router IGW/936-L – First Steps

D o c u m e n t R e v i s i o n 1 . 4

5.2 Ethernet Link

The Ethernet link between the PC and LAN1 of the IGW/9 6-L can be made on two ways:

• Direct with an Ethernet cross-over cable like shown in fig. 4.

• With two standard Ethernet patch cables over a hub or switch like shown in fig. 5.

Figure 4: Ethernet link with cross-over cable

Please note:

For the Ethernet connection in fig. 4 it is absolutely required to use a cross-over ca-

ble. Do not use an ordinary patch cable. Ethernet patch and cross-over cables are in

most cases visual indistinguishable. But the internal wiring is fully different. Mixing

up these types of cables leads to LAN errors. Hence pay attention to the label of the

cable or packing.

Figure 5: Ethernet link with hub or switch

The IP address of the LAN1 interface is ex-factory set to 192.168.0.126.

LTE Router IGW/936-L – First Steps

D o c u m e n t R e v i s i o n 1 . 4

5.3 Serial Ports COM2 and COM3

You can create an RS485 serial link on port COM2 and COM of the IGW/9 6-L.

An RS2 2 serial link is only possible on port COM .

Figure 6: Serial links on COM2 and COM3

Termina

Signa

COM

RS485 Serial Port RX /TX+

COM2

RS485 Serial Port RX /TX

Signal

Ground

Table 2: Screw ter inals COM2

Termina

Signa

COM

Serial Port: TXD (RS2 2), RX/TX

(RS485)

COM

Serial Port: RXD (RS2 2), RX/TX+ (RS485)

Signal Ground

Table 3: Screw ter inals COM3

Please note:

The RS485 (officially called TIA/EIA-485-A) connection between your IGW/9 6-L and

the field devices needs termination resistors on both ends for proper operation. The

IGW/9 6-L does not offer internal ter ination resistors. Please make sure, that the

RS485 cable connection is equipped with external termination resistors.

LTE Router IGW/936-L – First Steps

D o c u m e n t R e v i s i o n 1 . 4

5.4 Power S pply

The IGW/9 6-L needs a supply voltage of 11 – 28 VDC to work.

Connect the cables of an appropriate power supply to provide the system with the neces-

sary power like shown in fig. 7.

Figure 7: Power supply for the IGW/936-L

Termina

Signa

Vin (11 .. 28 VDC)

GNDin

Table 4: Screw ter inal power

CAUTION!

Providing the IGW/9 6-L with a higher voltage than the regular 11 – 28 VDC could cause

damaged device components!

Do NOT turn on the power supply while connecting it with the IGW/9 6-L. This could cause

damaged device components! First connect the power supply and THEN turn it on.

Table des matières

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité