Sper scientific 850011 Manuel utilisateur

Chroma Light Meter

850011

Instruction Manual

Chroma Light Meter - 850011

The contents of this manual may not be reproduced

or transmitted in any form or by any means electronic,

mechanical, or other means that do not yet exist or may

be developed, including photocopying, recording, or

any information storage and retrieval system without the

express permission from Sper Scientic.

TABLE OF CONTENTS

PRODUCT INTRODUCTION .................... 4

SAFETY INFORMATION ........................ 5

LCD AND CONTROL PANEL .................... 7

REAR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

PROBE ..................................... 8

MEASUREMENT PROCEDURE .................. 9

MAINTENANCE ............................. 26

BATTERY REPLACEMENT .................... 27

SPECIFICATIONS ............................ 28

WARRANTY ................................ 30

PRODUCT INTRODUCTION

• Illuminance in Lux or FC

• Color temperature and correlated color temperature

• Custom reference value of color di󰀨erence

Enables precise measurement of illuminance, color

temperature, correlated color temperature or color di󰀨er-

ence simultaneously shown on a backlit display. Excellent

for art galleries and museums, lm and TV studios, lighting

manufacturers, stores and designers. Meets CIE photopic

spectral response and color temperature. Lux and foot

candle selectable with general or LED light modes and a

hold function. Comes in a protective foam lined carrying

case complete with a tripod screw, magnetic mount, 9V

battery and instructions. N.I.S.T. traceable certicate of

compliance available (for lux and foot candles only).

Weight: 16 oz (453g)

Dimensions: 5 ½” x 2” x 1” (140 x 49 x 29 mm)

SAFETY INFORMATION

Read the following safety information carefully before at-

tempting to operate or service the meter. Only qualied

personnel should perform repairs.

Safety Symbols

CE Certication.

This instrument conforms to the following standards:

EN61326: Electrical equipment for measurement, control

and laboratory use.

IEC61000-4-2: Electrostatic discharge immunity test.

IEC61000-4-3: Radiated, radio-frequency, electromagnetic

eld immunity test.

IEC61000-4-8: Power frequency magnetic eld immunity

test.

Tests were conducted using a frequency range of 80-

1000MHz with the instrument in three orientations. The

average error for the three orientations is ±3% at 3V/m

throughout the spectrum.

However, between 180-500MHz at 3V/m, the instrument

permissive loss of performance is specied by the

specications.

Restrict to use of six substances within electrical and

electronic equipment (EEE), thereby contributing to the

protection of human health and the environment.

Precautions

Be sure to adhere to the following points to avoid injury.

• Please read the manual carefully to ensure safe and

correct use of this meter before using. Please reread if

necessary.

• Do not immerse the meter in water.

• Do not disassemble or modify the meter.

• Do not attempt to repair it yourself if the meter

malfunctions.

• Only qualied personnel may do it.

• Do not press, push or strike the LCD and sensor head.

• Do not use the meter in places where ammable or

near re.

• Do not use this meter in environments outside the

range of: 32ºF (0°C) to 122ºF (50°C) at Relative

Humidity no higher than 80%.

• When not in use, close the receptor cover.

• Be aware the accumulation of irradiations would cause

the sensor continue to age. Please keep away the light

source and cover with the cap when the unit is not in use.

• If the meter will not be used for a long time, remove the

battery and close the receptor cover.

• Never use organic solvents to clean the meter. (such

as thinner, benzene, etc.)

A. Data Hold Symbol

B. SET Function Symbol

C. Low Battery Symbol

D. Measuring Symbols of

Primary Reading

E. Measuring Symbols of

Secondary Reading

F. Measuring Symbols of

Tertiary Reading

G. Illuminance Unit

(lx or fcd) Symbol

H. Primary Reading

I. Color Temperature

Unit (K) Symbol

J. Secondary Reading

K. Light Source Symbol

(FL, INC or LED) (522)

L. Tertiary Reading

M. Unit / Down Button

N. Mode Button

O. (Color Di󰀨erence) /

Up Button

P. Power and Hold Button

LCD AND CONTROL PANEL

REAR

PROBE

Q. Tripod Socket

R. Battery Cover

S. Magnet Position

T. Anti-slippery Pad

U. Receptor Head

V. Receptor Cover

W. Grip

OPERATION INSTRUCTION

Main Function

Power On/O󰀨

Press and hold the Power button for 2 seconds to turn the

meter on and all of symbols will appear for 2 seconds on

the LCD. After power-on, the meter will measure and show

the readings on the LCD continuously. Press and hold the

Power button for 2 seconds again to turn the meter o󰀨.

Measuring Units

Press the button to select the illuminance (Ev) unit:

Lux (lx) or foot-candle (fcd).

Measuring light source selection(522)

After power-on, select the type of light sources to be

measured.

In the CT or CT display mode, press button

for 3 seconds to select di󰀨erent light source three dif-

ferent light sources can be selected: FL(Fluorescent),

INC(Incandescent) and LED.

The CT value will be more accurate when the selected light

source corresponds to the light source is being measured.

“----”, indicates that the measured CT value exceeds the

light source’s dened value. Please select a di󰀨erent light

source mode.

Data Hold

While measuring, press the HOLD button once to freeze

the display. HOLD will appear on the LCD. Press HOLD

button again to resume measuring.

Table des matières

Autres manuels Sper scientific Instrument de mesure

Sper scientific

Sper scientific 840005 Manuel utilisateur

Sper scientific

Sper scientific 850039 Manuel utilisateur

Sper scientific

Sper scientific 800046 Manuel utilisateur

Sper scientific

Sper scientific 300037 Manuel utilisateur

Sper scientific

Sper scientific 840007 Manuel utilisateur

Sper scientific

Sper scientific 840046 Manuel utilisateur

Sper scientific

Sper scientific 840064 Manuel utilisateur

Sper scientific

Sper scientific 840087 Manuel utilisateur

Sper scientific

Sper scientific 800052 Manuel utilisateur

Sper scientific

Sper scientific 860041 Manuel utilisateur

Sper scientific

Sper scientific 300003 Manuel utilisateur

Sper scientific

Sper scientific 840024 Manuel utilisateur

Sper scientific

Sper scientific 840006 Manuel utilisateur

Sper scientific

Sper scientific 840018 Manuel utilisateur

Sper scientific

Sper scientific WBGT Manuel utilisateur

Sper scientific

Sper scientific 300001 Manuel utilisateur

Sper scientific

Sper scientific 840062 Manuel utilisateur

Sper scientific

Sper scientific 840065 Manuel utilisateur

Sper scientific

Sper scientific 850023 Manuel utilisateur

Sper scientific

Sper scientific 840029 Manuel utilisateur

Sper scientific

Sper scientific 850070 Manuel utilisateur

Sper scientific

Sper scientific 850026 Manuel utilisateur

Sper scientific

Sper scientific 850020 Manuel utilisateur

Sper scientific

Sper scientific 840021 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur