Sper scientific 800020 Manuel utilisateur
1
Bluetooth Datalogging
Thermo-Hygrometer
800020
Instruction Manual
2
TABLE OF CONTENTS
INTRODUCTION ................................................................ 3
FEATURES.......................................................................... 4
MATERIALS SUPPLIED .................................................... 4
FRONT PANEL DESCRIPTION......................................... 5
LCD DISPLAY ..................................................................... 6
SET UP................................................................................ 7
MEASUREMENT PROCEDURES................................... 12
SOFTWARE INSTALLATION........................................... 17
DATALOGGING.................................................................. 19
POWER SUPPLY.............................................................. 24
CARE AND MAINTENANCE............................................ 25
SPECIFICATIONS ............................................................ 26
WARRANTY ...................................................................... 28
3
INTRODUCTION
This Sper Scientic Bluetooth Datalogging Therm-
Hygrometer with dewpoint and wet bulb (Model 800020)
accurately measures the ambient air while streaming
instantly to any iOS or Android smartphone. This
multiparameter meter also has a contact thermocouple
port to detect surface temperatures. All parameters have
an optional audible and visible alarm that can be seen at a
distance. The large backlit LCD simultaneously displays all
values while concurrently streaming to a smartphone and/
or a computer. Up to 32,000 complete data records with
GMP compliant date/time stamping can be stored in the
meter and later downloaded or conveniently e-mailed if a
PC is unavailable at the time. All data can be viewed and
stored in Excel format or you can use our unique graphing
tools in the included software to view and analyze the data.
Calibrate to known standards using the oset function for
humidity, ambient air temperature, and ice-point. The meter
comes ready to use with a protective foam-lined carrrying
case, Type K beaded wire probe, micro USB cable, a built-
in easel stand, 4 AAA batteries, and instruction manual.
FCC ID: 2AB7UBTXX0
This device and enclosed comply with part 15 of the FCC
Rules. Operation is subject to the two following conditions:
(1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
4
FEATURES
• Large LCD screen
• Measures in °C, °F, or Kelvin
• Customizable high and low alarms for all parameters
• Maximum/minimum/average values
• Oset function for all parameters
• 32,000 data points
• Direct upload of data to EXCEL, text, or graph les
• Customizable data graphing
• Automatic shuto
• Backlight
• Bluetooth® streaming and data sharing
MATERIALS SUPPLIED
• Datalogging Thermometer
• Micro USB Cable
• One K-type Beaded Wire Probe
• Free Software Download at:
www.sperdirect.com/software.htm
• Free App Download at:
• Instruction Manual
• Four AAA batteries
• Carrying Case
• Bluetooth® 7-pin adapter
5
FRONT PANEL DESCRIPTION
1. Ambient Temperature
and Humidity Probe
2. LCD Display
3. POWER Button
4. LEFT Arrow and MIN/
MAX
5. RECALL Memory Button
6. SET Button
7. Backlight Button
8. Up Arrow and Hold Button
9. Right Arrow and UNIT
Selection
10.Down Arrow and REC
Button
11. MEM Button
12.Thermocouple Input
13.Bluetooth® Chip
14.Micro USB Port
15.Bluetooth door
16.Tilt Stand
17.Battery Chamber
6
LCD DISPLAY
1. Thermocouple Type Selected
2. Bluetooth Activated
3. Wet Bulb Active on T1
4. Current RH Reading
5. Auto Power-o is Enabled
6. Low Battery Indicator
7. Min/Max/Average Activated
8. Dew Point Active on T1
9. Current Ambient Air T1 Reading
10. Current Thermocouple Reading T2
7
SETUP
Note…
Install the Bluetooth adapter as described on page 11.
Meter On and O
1. Press POWER to turn the meter on.
2. Press and hold POWER for 3 seconds to turn the meter o.
Setup Mode
1. Press POWER to turn the meter on.
2. Press SET to enter Setup Mode.
3. Press MEM to save each setting choice and continue
cycling through the setup options.
Note…
After each change is made, pressing SET will also save
the setting but will exit Setup Mode. The meter will return to
Normal Mode if the SET button is pressed..
Bluetooth Selection
1.
Press SET to enter Setup Mode
.
2. “bluetooth” appears on the display along with the word
“on” or “o”. Press
▲or ▼ to select “on”
3. Press MEM to save the selection and toggle to the next
setting. Otherwise, press SET to exit setup mode.
Thermocouple Type
1. Press SET to enter Setup Mode
.
2. Press MEM to toggle through the settings until “Type” appears
on the display along with the thermocouple type.
Press
▲or ▼ to cycle through K, J, E, T, N, R, and S types.
3. Press MEM to save the selection and toggle to the next
setting. Otherwise, press SET to exit setup mode.
8
Unit of Measure
1. Press SET to enter setup mode.
2. Press MEM to toggle through the settings until “Unit”
appears on the display along with ashing symbols for
°C, °F, or K. Press
▲or ▼ to cycle to your desired
temperature unit.
3. Press MEM to save the selection and toggle to the next
setting. Otherwise, press SET to exit setup mode.
Time Interval
The time interval range for data storing is 1 second to 60
minutes 59 seconds. The time interval denes how often a
reading is taken during record mode.
1. Press SET to enter setup mode.
2. Press MEM to toggle through the settings until “Int”
appears on the display along with the time interval in
minutes and seconds.The minutes ash on the display.
3. Press ▲or ▼ to adjust the minutes.
4. Press ◄ or ►to move the cursor to the required number
of seconds. The seconds will ash.
5. Press ▲or ▼ to adjust the seconds.
6. Press MEM to save the selection and toggle to the next
setting. Otherwise, press SET to exit setup mode.
Oset Values
All parameters can be adjusted to compensate for probe
errors. The oset range is ± 5°C or ± 9°F.
1. Press SET to enter setup mode.
2. Press MEM to toggle through the settings until OFFSET
appears at the bottom of the screen. Press ▲or ▼to
increase or decrease the oset value as compared to
a known standard such as an ice bath or humidity salt
chamber.
9
3. Press ◄ or ► to advance to the next parameter.
4. Press MEM to save the selection and toggle to the next
setting. Otherwise, press SET to exit setup mode.
Audible and Visible Alarms
High and low alarm values may be set for all parameters.
1. Press SET to enter setup mode.
2. Press MEM to toggle through the settings until ALARM
appears at the bottom of the screen. Press ▲or ▼ until
the word “On” appears on the screen.
3. Press MEM to advance into the alarm settings.
4. Use the ◄ or ► to advance through the placeholders and
the ▲or ▼ buttons to change the numbers. Press MEM
to save the selection and toggle to the next parameter.**
**Note: The alarm function is either on for all parameters
or o for all parameters. The best way to alarm only one
parameter is to set the values of the unwanted parameters
to something not possible during your measurement period.
For example, if you don’t want the humidity to alarm, set the
high for 99% and the Low for 0%.
5. Continue to set the High and Low alarms using the ▲or ▼
buttons for each parameter.
6. Press MEM to save the selection and toggle to the
next setting. Otherwise, press SET to exit setup mode.
10
Programming the Automatic shut o
1. Press SET to enter setup mode.
2. Press MEM to toggle through the settings until the
auto-power o icon appears in the upper left corner along
with the word “o” or “on.”
3. Press ▲or ▼ until the word “On” appears on the screen.
4. Use the ◄ or ► arrows to toggle through the available shut
o times. The meter can be preset to shut o automatically
after 10 minutes, 30 minutes, or hour increments of 1, 2, 4 or 8.
5. Press MEM to save the selection and toggle to the next
setting. Otherwise, press SET to exit setup mode.
Setting the Date and Time
1. Press SET to enter setup mode.
2. Press MEM to toggle through the settings until the Year,
Date, and time appear on the screen, along with the
word “SET”.
3. Press ▲or ▼ to adjust the year.
4. Use the ◄ or ► to advance to the date.
5. Press ▲or ▼ to adjust the date and time after advancing
to it.
6. Once the date and time have been set, press MEM
to save the selection and toggle to the next setting.
Otherwise, press SET to exit setup mode.
Table des matières
Autres manuels Sper scientific Instrument de mesure
Sper scientific
Sper scientific 840022 Manuel utilisateur
Sper scientific
Sper scientific 850051 Manuel utilisateur
Sper scientific
Sper scientific 800015 Manuel utilisateur
Sper scientific
Sper scientific 850068 Manuel utilisateur
Sper scientific
Sper scientific 850081 Manuel utilisateur
Sper scientific
Sper scientific 840046 Manuel utilisateur
Sper scientific
Sper scientific 840021 Manuel utilisateur
Sper scientific
Sper scientific 840087 Manuel utilisateur
Sper scientific
Sper scientific 300037 Manuel utilisateur
Sper scientific
Sper scientific 840003 Manuel utilisateur
Sper scientific
Sper scientific 840080 Manuel utilisateur
Sper scientific
Sper scientific 800021 Manuel utilisateur
Sper scientific
Sper scientific 800012 Manuel utilisateur
Sper scientific
Sper scientific 860045 Manuel utilisateur
Sper scientific
Sper scientific 300005 Manuel utilisateur
Sper scientific
Sper scientific 840021 Manuel utilisateur
Sper scientific
Sper scientific 850006 Guide d'installation et d'utilisation
Sper scientific
Sper scientific 840060 Manuel utilisateur
Sper scientific
Sper scientific 850003 Manuel utilisateur
Sper scientific
Sper scientific 900019 Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur