Spektrum DX Series Manuel utilisateur

Spektrum DXs Transmitter

Stick Mode Change Guide

You can change transmitter modes among Modes 1, 2, 3 and 4. This conversion requires both a

programming and a mechanical change

Please note that your DXs transmitter may need an update to perform this function. Make sure that it

is on version 1.29 or higher

Update Instructions

***Required Equipment***

- Windows based PC or Laptop with USB Port

- Spektrum USB Programmer (SPMA3065)

- SPMA3068 Adapter (not included with models that came equipped with DXs)

1. Download the Spektrum PC programmer Application and Install –Link here

2. Plug in Spektrum USB programmer cable into open USB Port

3. Open Spektrum PC Programmer Application on your PC

4. In the Top left corner of the App there is a Login button, use this to login to your

Spektrum Account or to create a new account

5. Plug the servo lead end of the USB programmer into the adapter and then plug

adapter into port on your DXs and power on

6. At this time, you should be presented with the Software Update Screen Menu

a. Here you are presented with the Serial Number and you can register the device to

your account by clicking Check for Update

7. Click Check for Update and choose the most recent update at the top of the list

a. Click Update and the transmitter will update. Please wait until the process

is complete before powering down and unplugging cables

Need help? Go to these links for a hands-on video walkthrough to

update transmitters via USB Cable –Click here

Spektrum DXs Transmitter

Stick Mode Change Guide

Stick Mode Change Instructions via Trim Programming

1. To enter trim programming mode, push and hold the Aileron and Rudder trim buttons outward

while you power ON the DXS transmitter.

2. 1 of the 4 Battery level indicator LEDs will light up Green. This indicates the current Stick Mode

selected

The LED will glow BLUE

when in Mode Change

programming mode

Press the A button to

save your selection. The

transmitter will power

down automatically

Mode 1

Mode 2 (default)

Mode 3

Mode 4

Use the Right Up

Trimmer to select your

desired Stick mode

Spektrum DXs Transmitter

Stick Mode Change Guide

Mechanical Conversion

Mechanical conversion is required to change between Modes 1 and 2 or between Modes 3 and 4.

The mechanical conversion consists of the following steps:

1. Change the Throttle Ratchet

2. Adjust the Elevator Centering Screw

CAUTION: Always power off the transmitter, disconnect and remove the battery before adjusting

stick tension or friction straps. Not doing so could result in property damage or injury

Changing the Throttle Ratchet

1. Disconnect the battery holder or optional battery

from the transmitter and set aside.

2. Remove the six Phillips head screws that secure the

rear transmitter case half.

3. Put the transmitter face down on a piece of foam or

a towel and remove the rear case.

CAUTION: Use care to not pull or disconnect any of

the wires attached to the back transmitter half.

4. Locate the silver throttle friction straps on both

gimbals. One strap engages a serrated section on the

gimbal for a ratcheted throttle, while the other strap

engages the smooth section on the gimbal.

5. To change the throttle ratchet, loosen the throttle strap so it does not touch the throttle gimbal.

Tighten the opposite throttle strap to engage the desired throttle ratchet.

Adjusting the Elevator Centering Screw

When changing between Modes 1 and 2, or between Modes 3 and 4, you must adjust the elevator

centering screw.

1. Hold the Elevator or Throttle stick in the full up or

full down position when you are adjusting the elevator

centering screw. Holding the gimbal stick reduces the

load on the elevator centering mechanism and makes

it easier to adjust the centering screw.

2. Locate the gimbal where the elevator centering

spring is engaged. Use a Phillips screwdriver to tighten

the elevator centering screw. Tightening the screw will

disengage the centering spring.

3. Using a Phillips screwdriver, loosen the opposite

elevator centering screw until the lever engages.

Table des matières

Autres manuels Spektrum Télécommande

Spektrum

Spektrum DX3C Manuel utilisateur

Spektrum

Spektrum DSM Manuel utilisateur

Spektrum

Spektrum AR635 Manuel utilisateur

Spektrum

Spektrum SLT3 3CH Manuel utilisateur

Spektrum

Spektrum DX5 PRO Manuel utilisateur

Spektrum

Spektrum DX8 Manuel utilisateur

Spektrum

Spektrum DX18 Manuel utilisateur

Spektrum

Spektrum DX3C Guide de démarrage rapide

Spektrum

Spektrum DX5C Manuel utilisateur

Spektrum

Spektrum DX6I Mode d'emploi

Spektrum

Spektrum DX18 Manuel utilisateur

Spektrum

Spektrum DX7 Manuel utilisateur

Spektrum

Spektrum DX3S Manuel utilisateur

Spektrum

Spektrum DX8 Manuel utilisateur

Spektrum

Spektrum DX9 Manuel utilisateur

Spektrum

Spektrum SR3300T Manuel utilisateur

Spektrum

Spektrum DSM DX5C Manuel utilisateur

Spektrum

Spektrum DX6R Manuel utilisateur

Spektrum

Spektrum DX3 Manuel utilisateur

Spektrum

Spektrum DX8 Manuel

Spektrum

Spektrum DX3R Manuel utilisateur

Spektrum

Spektrum DX3E Manuel utilisateur

Spektrum

Spektrum DX3S Manuel utilisateur

Spektrum

Spektrum NX7e Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation