Spektrum DX8 Manuel

Spektrum DX8 - DLG Setup in Sailplane mode

Sailplane mode has been made available since April 2013. If you have not updated their firmware,

please visit http: www.spektrumrc.com to get the firmware and setup instruction. This instruction set is

mainly used for setting up a Discus Launch Glider (DLG) with flaperons using a Spektrum DX8 on any

6ch receivers.

Note: Setup may differ according to each pilot's preference and below is a setup to start.

System Setup Page (switch x on with Roller Switch pressed down)

Model Name

Give your model a name. Maximum allowed characters = 10

By holding the roller switch and turning on the power switch, the TX will go in to the System Setup page.

Select an available model.

Model ype

Select Sailplane mode and confirm YES.

Warning: All previous data in the selected model will be lost after confirmation.

Wing ype

Wing: Dual Ail Tail: Normal Motor: Inhibit

Switch Select Setup

The Trainer Bind button is on the left of the aerial. The Trainer Bind button will be used for my launch

preset. For the pushbutton to function as the preset, you need to assign them to an Aux. I assigned

Aux2.

Note: You need to set "Aux2:lnh” before you can set "Trainer: Aux2"

Flight Mode Setup

I only have 3 flight modes:

Launch

Cruise

Thermal

If this is the case, select "2 or 3 Flight Modes" and assign your preferred switch (I use F Mode)

Now the System Setup is completed. Press back button to exit Setup to Main Panel.

----------------------------------------------------------------------------------------------------------------------------------------

Press roller switch to enter into Function List Menu.

Servo setups

Set all your servos so that all surfaces are centred and throws are as required.

Control Motor R Ail Elev Rudd Gear L Ail Aux2 Aux3

Travel 100 100 45 45 70 85 128 128 100 100 45 45 100 100 100 100

Sub Trim 0 7R 0 6R 0 7R 0 0

Reverse

Speed

N or R N or R N or R N or R N or R N or R N or R N or R

Starting setups which may need changing later

These Sub Trims will vary as you find the Zero Centring for each control

Set Reverse so that your servos travel in the direction you require

Dual rate (D/R) and Expo

The throws are adjusted based on feel. If you have unsteady thumbs use lots of Expo on all controls. Set

them according to your flying style.

Differential

UP Aileron is set to move more by proportion to the Down Aileron on the other side.

Set to On and vary the % to get the amount of Differential you need to avoid asymmetric Aileron

behaviour.

Camber Presets

Flight modes are pretty subjective. Some models have different preference. Different settings are used

on different models and you take time trimming these settings out on the field. In general, the starting

settings on this particular model are:

Launch mode - Reflex -1.5mm, elevator -0.75mm

Cruise mode - Camber 0mm, elevator 0mm

Thermal mode - Camber +2.5mm, elevator +1mm

Flight modes settings can be done in the "Camber Presets" page. Initial settings are shown in the photo

below. Do note that the Elev % numbers are adjusted at the field.

Launch Preset

At launch, to rotate the DLG up use some elevator up input using the bind button. Launch preset is setup

in the "Mixing" menu.

Select an available mix and assign AX2 to mix with ELE. The rate is adjusted at the field according to

your preference.

Reminder: The Aux2 button was assigned earlier (see Switch Select Setup). Air Brakes)

Air brakes are activated using the throttle stick (down position).

While in the Camber System page, position the flight mode switch at Launch position (position 0). Select

input as "Spoiler Stick". Position the throttle stick to where you want to activate the airbrakes. Adjust the

Aileron rates according to your preference.

Select Cruise mode using F-mode switch (position 1). Repeat adjustment similar to Launch mode

Select Thermal mode using F-mode switch (position 2). Repeat adjustment similar to Launch mode

Note: Offset settings depends how your aileron servo horns are mechanically setup. Adjust accordingly.

Do try playing around with the rates as it may differ from model to model.

Flap/Elevator Mix

After the flaperons have been setup, the elevator needs to compensate to prevent the DLG from

ballooning up when the air brakes are activated. In the Mixing menu, go into Flp>Ele mix to setup the

elevator compensation. The settings below should be good enough to start with final values should be

done at the field.

Autres manuels pour DX8

Table des matières

Autres manuels Spektrum Télécommande

Spektrum

Spektrum DX7s Manuel utilisateur

Spektrum

Spektrum SLT3 3CH Manuel utilisateur

Spektrum

Spektrum AR8010T Manuel utilisateur

Spektrum

Spektrum DX3C Manuel utilisateur

Spektrum

Spektrum DX8 Manuel utilisateur

Spektrum

Spektrum ix20 Manuel utilisateur

Spektrum

Spektrum NX7e Manuel utilisateur

Spektrum

Spektrum DX8 Manuel utilisateur

Spektrum

Spektrum AR6400NBL Manuel utilisateur

Spektrum

Spektrum DX6R Manuel utilisateur

Spektrum

Spektrum DX7 Manuel utilisateur

Spektrum

Spektrum DX3E Manuel utilisateur

Spektrum

Spektrum DX3C Guide de configuration

Spektrum

Spektrum DSM Manuel utilisateur

Spektrum

Spektrum DSM DX5C Manuel utilisateur

Spektrum

Spektrum DX7 Manuel utilisateur

Spektrum

Spektrum DX4S Manuel utilisateur

Spektrum

Spektrum DX6I Mode d'emploi

Spektrum

Spektrum DX2S Manuel utilisateur

Spektrum

Spektrum DX4C Manuel utilisateur

Spektrum

Spektrum DX3C Manuel utilisateur

Spektrum

Spektrum DX8G2 Manuel utilisateur

Spektrum

Spektrum PowerSafe AR9130T Manuel utilisateur

Spektrum

Spektrum BEASTX AR7210BX Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation