Message Lamp LED
(Red)
Temp LED
(Red)
Power LED
(Red)
Power LED
(Blue)
Power Plug Flash ON to OFF
100ms
Flash ON to OFF
100ms
Flash ON to OFF
100ms -
Standby -- ON -
Power button ON -- - ON
Cooling state --
0.5 second H(ON),
0.5 second L(OFF)
flashing
-
Power button OFF:
Cooling completed; Standby Mode -- ON -
Firmware download ON ON ON -
Thermal sensor error , OSD showing as below:
1. Make sure air in and outlets are not
blocked.
2. Make sure the environment temperature
is under 40 degree C.
-ON -ON
Fan lock error , OSD showing as below:
The projector will switch off automatically -
0.5 second H(On),
0.5 second L(Off)
flashing
-ON
Lamp error (Lamp, Lamp driver, Color wheel) ON - - ON
Installation
34
LED Indicator Messages
Troubleshooting
●
●
NOTE
Power Cord1.
Audio Cable *2.
VGA to DVI-A Cable *3.
VGA Cable4.
RS232 Cable *5.
HDMI Cable *
6.
USB Cable *7.
Interactive Cable *8.
Network Cable * (WXGA)9.
Connecting to Computer/Notebook Connecting to Video Sources
Power Cord1.
Microphone Cable *2.
Audio Cable Jack/RCA *3.
S-Video Cable *4.
Audio Cable *5.
VGA to HDTV (RCA) Cable *6.
HDMI Cable *7.
8. Composite Video Cable *
Due to the difference in applications for each country, some regions may have different accessories.
* Optional accessory
<Image Problems>
Q: No image appears on-screen.
A: 1. Ensure all the cables and power connections are
correctly and securely connected as described in the
“Installation” section.
2. Ensure the pins of connectors are not crooked or broken.
3. Check if the projection lamp has been securely installed.
4. Ensure that the “Blank” feature is not turned on.
<Projector Problems>
Q:The projector stops responding to all controls.
A: If possible, turn off the projector, then unplug the power
cord and wait at least 20 seconds before reconnecting
power.
Q: Lamp burns out or makes a popping sound.
A: When the lamp reaches its end of life, it will burn out
and may make a loud ``popping sound. If this happens,
the projector will not turn on until the lamp module has
been replaced.
<Remote Control Problems>
Q: If the remote control does not work.
A: 1. Check the operating angle of the remote control is
within ±30° both horizon-tally and vertically of one of
the IR receivers on the projector.
2. Make sure there are not any obstructions between the
remote control and the projector. Move to within 7 m (±0°)
of the projector.
3. Make sure the batteries are inserted correctly
4. Replace batteries if they are exhausted.
<Sound Problems>
Q: If no sound from the projector.
A: 1. If you are playing an external source, make sure you have
an audio cable ``securely connected between the source
device and the projector’s audio input.
2. Please make sure the external speakers are not connected.
3. Make sure the volume is not set to minimum.
4. Make sure the “ Volume --> Mute” function is set to “off”.
● Projector
● IR Carmer Module
● Light Curtain ( for 310Wi-T )
( for 310Wi-P & 310Wi-T)
LAN
Notebook
Computer
Power socket
1
22
2
4
4
Monitor
Audio Output
Light Curtain
3 4 5 6 7 8
9
LAN
DVD player, Set-top box,
HDTV receiver
S-Video output
Video output
1
6
2
Power socket
Audio Output
DVD player, Set-top box,
HDTV receiver
5
3 4 5 6
7
583
1. Use this feature to enable the Interactive
function. Options are: “Off” and “On”.
2. You need to use a Mini USB cable to
connect Laptop/desktop with the projector
before using the Interactive function.
1. For magnetic whiteboard: attach Curtain base plate to
Light Curtain module first and avoid interlock switch fail.
Put Light Curtain module onto whiteboard and magnets
at the back of Curtain module will be attached.
2. Install Light Curtain base plate by using 2 M3 screws
Option 2 is recommended regarding environmental factors such
as temperature, humidity, vibration and others.
2-1. Customized whiteboard is incorporated with Light Curtain
base plate design.
2-2. Regular whiteboard, the Light Curtain base plate needs to be
installed first by using 2 M3 screws.
3. Use special glue(ex: AB glue) to adhere Curtain base plate to
the whiteboard. Then place Light Curtain module onto Curtain
base plate.
4. This option is suitable for demonstration ONLY.
Use a piece of good quality double-sided adhesive (thickness less
than 0.5mm) to adhere Curtain base plate onto the whiteboard.
Then place Light Curtain onto the Curtain base plate.
B: After Installtion the Light Curtain, open
the top cap of Light Curtain module and
plug in Interactive cable.
A: There are 4 available options :
