Spedal CL796 Series Manuel utilisateur
USER MANUAL
Smart Multimedia Dashcam
017C2128-EN
CL796 Series
CONTENT
To protect our earth, please use the e-version of this manual. If you
encounter any problems while reading this manual or using the
1. DISCLAIMER AND SAFETY GUIDELINES 1
1.1 Disclaimer 1
1.2 Safety Guidelines 2
2. ACCESSORIES AND INTERFACES 3
2.1 In the box 3
2.2 Product Diagram 4
2.3 Installation Guideline 5
2.4 Interfaces Introduction 8
3. FUNCTIONS AND SETTINGS 9
3.1 General Settings 9
3.2 CarPlay / Android Auto and their settings 11
3.3 Recorder and its settings 12
3.4 FM and its settings 13
3.5 Playback and its settings 14
4. APPENDIX 15
4.1 Specifications 15
4.2 Warranty 15
1. DISCLAIMER AND SAFETY GUIDELINES
1.1 Disclaimer
This product is a smart multimedia dashcam. By using the built-in CarPlay and Android
Auto functions, you will be able to connect your mobile phones with this device and
manipulate your mobile phone Apps on this device . Please pay special attention to the
cautions and warnings in this User Manual. You can visit our homepage http://
www.spedal.cc to get relevant files of this product, including User Manual and other files.
Shenzhen Xinzhuang Gude Technology Co. Ltd. (Spedal) reserves the right to update this
User Manual.
The information in this document affects your safety, legal rights and responsibilities. Read
this entire document carefully to ensure proper configuration before use. Failure to follow
the instructions and warnings in this document may result in product damage or other
possible injury or loss. You must strictly follow Spedal's guidelines to install and use the
product, and never use non-standard parts. Before assembling, setting up and using, be
sure to carefully read all the instructions and warnings in this document. This product is not
a toy. Please do not allow children to touch this product or its parts and wires. Please be
careful when operating in scenes where children are present.
By using this product, you hereby signify that you have read this disclaimer carefully and
that you understand and agree to abide by the terms and conditions herein. The user
promises to be responsible for his actions and all consequences arising therefrom. The
user promises to use this product only for legitimate purposes, and agrees to all the terms
and contents of this document and any related policies or guidelines that Spedal may
formulate. You understand and agree that in the absence of videos or photos, Spedal may
not be able to analyze the cause of your product damage or accident, and cannot provide
you with after-sales service such as warranty.
Spedal is not responsible for all losses caused by the user's failure to use the product
in accordance with this User Manual.
In compliance with laws and regulations, Spedal reserves the right of final interpretation of this
document and all related documents of this product. If the manual is updated, revised or terminated,
we will not notify you personally. Please visit the official website of Spedal for the latest product
information. Spedal is a trademark of Shenzhen Xinzhuang Goodo Technology Co. Ltd. and its affiliates.
The product names, brands, etc. appearing in this article are all trademarks or registered trademarks of
their respective companies.
1
1.2 Safety Guidelines
Warnings
●Please use the original cable and power cords only;
●Do not exceed the rated voltage when using the device;
●Do not install or operate the device with wet hands;
●Do not install the device in places of high temperature, humidity;
●Do not install the device in places of flammable or explosive gases or liquids;
●Do not install the device in an area interfering with the driver's sight or driving safety;
●Do not install the device on the airbag cover or within the airbag’s working range;
●Do not leave the device in a closed vehicle under high temperature for a long time;
●Do not poke the device and its accessories using sharp objects such as awl or scissor;
●Do not disassemble, repair or modify the device and its accessories by yourself;
●Do not install, use or place the device within the reach of any children under 16;
●Do not cut the charging cable.
Notice: Damage caused to the dashcam as result of not obeying the warnings above is not
covered by the warranty!
Cautions
●Do not press the lens forcefully to avoid lens breakage or lens misalignment;
●Do not directly touch the lens surface to avoid stains that affect the recording effect;
●Do not remove the memory card to avoid file damage during the shutdown process;
●When using the memory card for the first time, please format it on the device to ensure
stable reading and writing;
●When not using the device for a long time, please pull out the memory card to ensure
the memory card’s performance.
2
2. ACCESSORIES AND INTERFACES
2.1 In the box
Before using this product, please check whether the product package contains all of the following
items. If anything is missing, please contact Spedal or your local agent.
Notice: Depending on which model you bought, you might have either Wire B or Wire C as
extension cable for back camera. Wire B is for pickups and Wire C is for trucks. Please use the
SPEDAL original cable and accessories only. Gifts and accessories are not covered by the
warranty. The content of this product package is subject to change without notice, the actual
package content shall prevail.
3
Smart Multimedia Dashcam
Suction Bracket
Sticking Bracket
In-Car Charger
Rear Camera
Wire A
(6.5m)
Wire B or C
(5m or 12.5m)
32GB TF Card
(Gift)
2.2 Product Diagram
4
Microphone
Screw hole for suction bracket
Sticking bracket
Screen
Left side Right side
3.5mm Port
TF Card Slot
AV-IN Port
Power Port
Power
Button
2.3 Installation Guideline
The device is in the storage state when it leaves the factory. Please follow the steps below
to prepare for installation:
1. Take the device and its accessories out of the box or plastic bag; .
2. Tear off the protective film on the screen and lens of the device; .
3. Remove the wire tie that binds the wire.
TF Card Installation
Insert the TF card into the slot with the pins facing downwards. Push the TF card forward,
and the card can be removed after it pops out. Please use the 32GB TF card that comes
with the product. A third-party TF card should meet these requirements: Class 8 or above,
maximal 128GB.
Note: Installing and removing the TF card in the recording mode may result in failure of recording
videos and causing damage to the TF card. Please turn off the device before inserting or
removing the TF card.
5
TF Card Installation
Suction Bracket Installation
1. Aim the screw of the suction bracket into the screw hole on the device; .
2. Rotate the suction bracket clockwise to tighten the screw; .
3. Select a proper position (such as the center of the front windshield), attach the suction
mound to the glass and press the lock piece to squeeze the air out of the suction cup;
4. Adjust the screen and lens angle.
Sticking Bracket Installation
1. Aim the clip of the sticking bracket at the mount buckle on the backside of the device;
2. Press the whole sticking bracket upwards to lock the clip and the buckle;
3. Tear off the protection film from the bottom of the sticking bracket;
4. Stick the sticking bracket on the dash board;
5. Adjust the screen and lens angle;
6
Suction Bracket Installation
Sticking Bracket Installation
Dashcam Installation
1. Insert the plug of the In-Car Charger into the cigarette lighter socket of the car;
2. Insert the Mini-USB plug of the In-Car Charger into the USB slot of the device;
3. Fix the device on the dash board by using the sticking bracket. You might use the
suction bracket to replace the sticking bracket and fix the device on the front windshield.
Back Camera Installation
1. Insert the plug of the back camera into the connection port of the connection cable
(6.5m, Wire A);
2. Insert the plug of the connection cable(6.5m, Wire A) into the AV-IN hole of the
dashcam;
3. Tear off the protection film from the sticker on the back camera;
4. Stick the back camera above he license plate and adjust the recording angle.
Note: If Wire A is not long enough for your car(such as pickup or truck), you might
use another extension cable(either Wire B or Wire C) in the package.
7
2.4 Interfaces Introduction
Main Interface
When you connect the device to the vehicle via the in-vehicle charging cable, the device
powers on after the vehicle starts. If you want to connect the device to the power in any
other way, press and hold the power button to turn it on. The screen after turning on the
device is as follows.
Note: For more detailed introduction of the device functions and settings, please refer to 3.
FUNCTIONS AND SETTINGS.
No.
Area
Function
①
Settings
General settings of the device.
②
CarPlay
Connecting your iPhone with this device
③
Android Auto
Connecting your Android mobile phone with this device
④
Recorder
Photo and video shooting during drive process.
⑤
FM
Mobile phone FM connection to the car loudspeaker.
⑥
Playback
View the photos and the videos.
8
CarPlay
Settings
12:00
08-08 Sunday
Recorder
Playback
FM
Android Auto
Table des matières
Autres manuels Spedal Caméra embarquée
Spedal
Spedal CL796P Manuel utilisateur
Spedal
Spedal CL796W Manuel utilisateur
Spedal
Spedal CL586 Manuel utilisateur
Spedal
Spedal CL586 Manuel utilisateur
Spedal
Spedal C326 Manuel utilisateur
Spedal
Spedal minieye C2M Manuel utilisateur
Spedal
Spedal CL796N Manuel utilisateur
Spedal
Spedal CL588 Manuel utilisateur
