Spectrum Industries 95513 Manuel utilisateur
Adjustable CPU Sling
#95513
Assembly Instructions:
Tools Required:
Phillips screwdriver
Drill with an 1/8" drill bit
(for desks without threaded inserts)
Before you begin, please make sure all parts and proper quantities are
included. Any parts damaged during shipment must be reported within
15 days of receipt. To report information regarding damages or if you
have any questions, please call 1-800-235-1262.
To purchase parts or accessories, please contact us at
www.spectrumfurniture.com
1-800-235-1262
Thank you for choosing Spectrum products!
(2) 026547
1/4-20 x 1-1/2 (2) 026017
1/4-20 x 1/2
PHMS
(1) 0100193
2" x 2" x 1" Shim (1) 042019
Leg Bracket
(1) 042139
Drill Template
(2) 034195
1/4-20 Wing Nut
(2) 021605
#10 x 1-3/4
PHSM
(2) 026057
#10 x 3/4
PHSM
(1) 044890
1" Nylon Spacer
(1) 042025
1/4-20 x 3/8
THMS
(2) 056703
Strap/Buckle
Assembly
1
Sling Assembly
0100192R3 Page 1 of 3
A. Assemble the sling side and base using (2) 1/4-20 wing nuts as shown in Figure 1A.
B. Thread the straps through the slots in sling side and base as shown in Figure 1B
with the tails hanging down. (The center slot can be used for smaller CPU's.)
C. Thread each strap through the buckles as shown.
Wing Nut
(2) Req'd
Strap/Buckle
Assembly
Sling Side
Sling Base
Figure 1A Figure 1B
Strap/Buckle
Assembly
Center slot used
for smaller CPU's
1. Sling Assembly
A. Determine whether the CPU Sling will mount on the right or left side of the desk and align the top sling holes with the appropriate set of
inserts. Figure 2A shows a sling being mounted on the left side of a desk.
B. Attach the Sling to the worksurface using two 1/4-20 PHM Screws and tighten.
1/4-20 x 1-1/2"
PHM Screw
2" x 2" x 1" Shim
Note: If desk does not have
threaded inserts, skip to step 3.
Support Brace
(dk)
1/4-20 x 1/2"
PHM Screw
2. Attaching Sling to desks with threaded inserts
Note: Desks without support brace (Figure 2A) use two 1/4-20 x 1/2" PHM Screws (026017.) For desks with Support Brace (Figure 2B), use one
Nylon Spacer (044890) in the front hole, and one 2" x 2" x 1" Shim (010093) in the back hole with the longer 1/4-20 x 1-1/2" PHM Screws (026547.)
The front of the sling will extend past the Support Brace.
0100192R3 Pa
g
e 2 of 3
1" x .275 ID x .5 OD
Nylon Spacer
(
on some
d
es
k
s
)
Figure 2B
Drill Template
042139
Leg
Worksurface
Support Brace
(on some desks)
Drill here
Drill here
3/4" Deep
1/8" Drill Bit
Figure 3A
Figure 2A
A. Determine whether the CPU Sling will mount on the right or left side of the desk.
B. Fold and tape the enclosed Drill Template (042139) to the underside of the worksurface in the position shown in Figure 3A.
Wrap a piece of tape around a 1/8" drill bit to mark 3/4" from the end of the bit-Figure 3B. Drill through the Template on the two marked
holes closest to the Leg, 3/4" deep. Figure 3A.
C. Attach CPU sling to worksurface using (2) #10 Sheet Metal Screws.
Figure 3B
Note: Desks without inserts or Support Brace use two #10 x 3/4" PHSM Screws (026057.) Desks without inserts that include a Support Brace as
in Figure 3A, use one Nylon Spacer (044890) in the front hole, and one 2" x 2" x 1" Shim (010093) in the rear hole using the longer #10 x 1-3/4"
PHSM Screws (021605.) The front of the CPU Sling will extend past the Support Brace (See Figure 2B for reference.)
3. Attaching Sling to desks without threaded inserts
Ta
p
e
0100192R3
Page
2
of
3
A. Line up the leg bracket with the front slot of the CPU sling as
shown and attach to the sling with a 1/4-20 x 3/8" THM Screw.
Figure 4.
B. Adjust the leg bracket until it is snug against the leg and tighten
screw.
1/4-20 x 3/8"
THM Screw
Leg Bracket
Note: If the CPU Sling is being used on a CLASS™ or Evolution™ desk, the included
(042019) Leg Bracket should be attached to the Sling and Front Leg.
4. Attaching Leg Bracket
5
Installing CPU
0100192R3 Page 3 of 3
Figure 4
A. Slide the base to the widest position and carefully place the CPU unit into the sling.
B. Slide the base tight against the CPU and tighten the two wing nuts underneath.
C. Make sure the CPU will be supported by both straps. Tighten the straps around the CPU while keeping the buckles
positioned as high as possible to avoid interference. Figure 5A. The center slot can be used with smaller CPU's. Figure 5B.
Figure 5A
Standard
CPU Small
CPU
Figure 5B
5. Installing CPU
Autres manuels Spectrum Industries Support et étagère
Spectrum Industries
Spectrum Industries 95532 Manuel utilisateur
Spectrum Industries
Spectrum Industries LT-30 Manuel utilisateur
Spectrum Industries
Spectrum Industries 95036 Manuel utilisateur
Spectrum Industries
Spectrum Industries 55491 Manuel utilisateur
Spectrum Industries
Spectrum Industries 68205 Manuel utilisateur
Spectrum Industries
Spectrum Industries 37141 Manuel utilisateur
Spectrum Industries
Spectrum Industries 55498 Manuel utilisateur
Spectrum Industries
Spectrum Industries 97525 Manuel utilisateur
Spectrum Industries
Spectrum Industries LT-30 Manuel utilisateur
Spectrum Industries
Spectrum Industries 55386 Manuel utilisateur
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
