Spectroline CC-80 Manuel utilisateur

OPERATING INSTRUCTIONS

CC-80 and CC-81

Fluorescence Analysis Cabinets

Manual No. AM11028

Printed in U.S.A. Issued: September 2011

CC-81

INTRODUCTION

The Spectroline CC-80 and CC-81 cabinets are specially designed for

efficient fluorescence analysis. Both units come equipped with a 25-watt

internal white light source, while the CC-81 is additionally supplied with

the Spectroline ENF-280C 365/254nm 8-watt UV lamp.

For a list of E-Series lamp models that work with either the CC-80 or CC-81

cabinets, please visit www.spectroline.com. Choose from the available

8-watt lamps listed under "E-Series Ultraviolet Hand-Held Lamps."

For greater epillumination options, these cabinets may be used with one

or two Spectroline E-Series UV lamps that are available in 254nm,

312nm or 365nm, or a combination of these wavelengths. For higher

UV intensity and increased fluorescent contrast with transillumination,

these units may be placed over a wide range of Spectroline UV

transilluminators.

CABINET DESCRIPTION

1. Eyepiece Flexible eyepiece with UV-absorbing viewing

Viewing Assembly window to protect the eyes and increase contrast.

2. Photographic Port Used when photographing samples. To expose,

remove the viewing assembly.

3. Master Power Controls power supply to the cabinet.

Switch

4. White Light Switch Controls the white light bulb.

5. Port Covers Cover the lamp port openings to ensure that

the cabinet is lighttight.

6. Lamp Ports Accommodate one or two E-Series* lamps.

7. Curtain Excludes ambient light.

8. Lamp Outlets Receptacles for plugs of E-Series* lamps.

*Use with any 8-watt Spectroline E-Series UV lamp.

WARNING

Please read the instructions in this manual carefully. Never use

this equipment in any manner not specified in these instructions

because the protection provided by the equipment may be

impaired.

2. Photographic Port

(under viewing

assembly)

1. Eyepiece Viewing Assembly

3. Master Power Switch

5. Port Cover

4. White Light Switch

6. Lamp Port

(under

port

cover)

7. Curtain 8. Lamp Outlets

UNPACKING AND INSPECTION

1. Carefully unpack and inspect the cabinet for possible damage in

shipment. If any damage is noted, immediately notify the carrier and

supplier before attempting to use the equipment.

2. Save the shipping carton and packing materials for future storing and

shipping of the equipment.

3. Check the lamp’s electrical performance as soon as possible

according to the GENERAL FUNCTIONAL CHECKS outlined in the

‘‘OPERATION’’ section of this manual.

OPERATION

GENERAL FUNCTIONAL CHECKS

1. Connect the cabinet plug to a power outlet that complies with the

electrical requirements specified on the unit’s label.

2. Depress the master switch to the ON position. This switch must be

activated to operate the E-Series UV lamp(s) or the white light bulb.

3. Test the white light bulb by pushing the white light switch ON.

4. Check the felt curtain by pushing it inward and upward until

it connects with the magnetic catch. This will allow clear

placement of samples.

CC-80

INSTALLATION

1. The power supply cord is the disconnect for this unit.

2. Check that the master and white light switches are both in

the OFF position.

3. Set the cabinet upright on a solid, level surface.

4. Place the lamp(s) in the lamp port(s), making sure the lamp cord(s)

remain outside the cabinet housing.

5. Plug the cord(s) into a lamp outlet.

6. Push the master power switch ON.

7. Operate the lamp(s) according to the manual enclosed

separately with each unit.

PORT COVERS

When the cabinet is not being used with two E-Series lamps

simultaneously, the unused port opening(s) on the upper portion of the

cabinet should be covered to exclude ambient light. Two port covers are

provided that fit easily into the openings.

BOTTOM PANEL

A black bottom panel is enclosed with the cabinet. When using the cabinet

without a transilluminator, the panel should be in place to ensure proper

shielding from ambient light. Remove the four round rubber screw holders

with a Phillips screwdriver. Align the four openings in the panel with the

bottom of the cabinet and reattach the rubber screw holders.

USING WITH A TRANSILLUMINATOR

Place the Spectroline UV transilluminator on a solid, level surface, filter

side up. Remove the bottom panel and reattach the rubber screw

holders to the bottom of the cabinet. These will prevent scratching of

the transilluminator surface.

WARNING

The transilluminator’s operation is separate from that of the

viewing cabinet. Do not attempt to plug the transilluminator into

the lamp outlets on the side of the cabinet. This will result in a

dangerous overload. The transilluminator must be plugged into a

separate external power source.

OPERATOR SERVICING

The following servicing instructions are intended for limited

maintenance of the cabinet. Do not perform any servicing other than

that contained in these instructions. Return the cabinet to the

factory for maintenance not covered in this section.

WARNING

To avoid the risk of electrical shock, always unplug both the

cabinet and the lamp(s) from their power sources before cleaning

or servicing. The power outlets in the cabinet will accommodate

only the Spectroline E-Series lamps.

HOUSING AND VIEWING WINDOW MAINTENANCE

Immediately clean all spills from the housing using water and a mild

detergent, if necessary, and wipe dry. Take care not to allow any liquids

to leak into electrical components. Periodically clean the UV-absorbing

viewing window with a glass cleaner and soft cloth.

ENVIRONMENTAL SPECIFICATIONS

The CC-80 and CC-81 cabinets are designed to be safe under the

following conditions:

• Indooruse;

• Altitudeupto2,000m(6,562ft.);

• Temperature5°Cto40°C(41°Fto104°F);

• Maximumrelativehumidity80%fortemperaturesupto31°C(88°F)

decreasinglinearlyto50%relativehumidityat40°C(104°F);

• Mainssupplyvoltagefluctuationsnottoexceed±10%ofthenominal

voltage;

• InstallationCategoryII;

• PollutionDegree2

ELECTRICAL SPECIFICATIONS

Both the CC-80 and the CC-81 fluorescence analysis cabinets are

equipped with a 25-watt internal white light bulb.

*Always specify the required voltage All /FE units conform to CE standards

Long Wave (UV-A) 365nm Medium Wave (UV-B) 312nm Short Wave (UV-C) 254nm

WARRANTY

The warranty policy for the CC-80 and CC-81 cabinets is provided on

the Certificate of Limited Warranty enclosed separately with each unit.

NOTE: For assistance of any kind, including help with a unit under

warranty, contact the Customer Service Department at Spectronics

Corporation. In the U.S. and Canada, call toll-free 1-800-274-8888.

Include the model and serial numbers of the unit and the date of

purchase. Shipping instructions will be provided if they are deemed

necessary. If an estimate of charges for nonwarranty work or other

service work is required, a quote will be furnished upon evaluation of

the unit. Service work will not be performed without customer approval.

SHIPPING

Carefully pack the equipment in the original shipping container and

packing materials. Insure it for full value and ship it prepaid to the factory.

MODEL DESCRIPTION TUBES FILTER VOLTAGE REQUIRED*

CC-80 Cabinet — — 120V/60Hz, 2.0A

CC-80/F Cabinet, European Plug — — 230V/50Hz, 2.0A

CC-80/FA Cabinet, Australia/China Plug — — 220-240V/50Hz, 2.0A

CC-80/FB Cabinet, UK Plug — — 230V/50Hz, 2.0A

CC-80/J Cabinet — — 100V/50-60Hz, 2.0A

CC-81 CC-80 Cabinet, with ENF-280C UV

Lamp, 8W Tubes (2), UV-A and UV-C

BLE-8T365

BLE-8T254

2F018 120V/60Hz, 2.0A

CC-81/FA CC-80/FA with ENF-280C/FA

(Australia/China Plug)

BLE-8T365

BLE-8T254

2F018 220-240V/50Hz, 2.0A

CC-81/FB CC-80/FB with ENF-280C/FB

(UK Plug)

BLE-8T365

BLE-8T254

2F018 230V/50Hz, 2.0A

CC-81/FE CC-80/F with ENF-280C/FE

(European Plug)

BLE-8T365

BLE-8T254

2F018 230V/50Hz, 2.0A

CC-81/J CC-80/J with ENF-280C/J BLE-8T365

BLE-8T254

2F018 100V/50-60Hz, 2.0A

CC-81/FB

CC-80 with ENF-280C/FB (UK)

230V/50Hz, 2.0A

REPLACEMENT PARTS

Description Product No.

Bulb, 25W—White Light BLE-1T261

Eyepiece, UV-Absorbing Window Assembly

LAMP CONTAINS MERCURY

Manage in Accord with Disposal Laws

See: www.lamprecycle.org

Caution (refer to accompanying documents)

CC-81/FB

CC-80 with ENF-280C/FB (UK)

230V/50Hz, 2.0A

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Spectroline Instrument de mesure

Spectroline

Spectroline AccuMax XRP-3000 Manuel utilisateur

Spectroline

Spectroline LeakTracker OIL-GLO ULTRA Manuel utilisateur

Spectroline

Spectroline Accupro XP-2000 Manuel utilisateur

Spectroline

Spectroline OIL-GLO ULTRA Manuel utilisateur

Spectroline

Spectroline GLO-Stick AC&R Dye Manuel utilisateur

Spectroline

Spectroline EZ-Ject AC&R Dye Manuel utilisateur

Spectroline

Spectroline AccuPRO XP-2000 Manuel utilisateur

Spectroline

Spectroline WATER-GLO ULTRA SPI-VLWGG Manuel utilisateur

Spectroline

Spectroline COBRA CAM Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur