Spectra Precision DG813 Mode d'emploi

DG813 & DG613

Pipe Laser

How to use the pipe lasers –step by step

November 2015_JS

DG813/DG613 Components

SF803

DG613

DG813

RC803 Recharge kit

1 –DG’s are shipped with a rechargeable

NiMH battery pack (Q104667).

Only the original rechargeable battery

pack allows charging with the

provided charger.

2 –An optional external charger Cable,

12V Battery w/Cigarette Lighter Plug

(P25) is also available

3 –Alkaline batteries can be used as a

backup

4 –Plus and minus symbols indicate

how to put the alkaline batteries into

the battery compartment

Powering the Laser

- Open the battery door by pulling out

the battery door latches.

- Push down the battery door and lift up

the locking lever that has the

two pins

- Insert batteries (or a rechargeable

battery pack) into the housing so

that the negative poles are on the

bigger battery spiral springs.

- Close the battery door and lock it by

pushing the door latches back to the

housing.

Installing Batteries

Powering the Remote Control RC803

1. Open the battery door using a coin or similar

pry device to release the battery door tab on

the RC803.

RC803 will be shipped with alkaline batteries

Rechargeable batteries can be used optional

but need to be charged externally.

2. Insert two AA batteries noting the plus (+)

and minus (-) diagrams inside the battery

housing.

3. Close the battery door. Push down until it

“clicks” into the locked position.

Using the Remote Control RC803

1. Press the button to turn on the Radio/IR

remote control.

If the RC803 is outside the radio operating range

the remote switches automatically into the IR

connection capability.

Note: When the remote control is initially turned

on, the standard display (model number and

software version) appear for the first 3 seconds,

then the grade value and line direction

indications briefly appear in the LCD.

With every button press, the LCD backlight is

activated and turns off automatically if no button

is pressed for 8 seconds.

To turn off the radio remote control, press and

hold the button for two seconds.

Note: 5 minutes after the last button press, the

remote control turns off automatically.

1. Open the battery door pulling the battery

door latch.

The SF803 will be shipped with 4 AA

alkaline batteries.

Rechargeable batteries can be used

optional but need to be charged externally.

2. Insert four AA batteries noting the plus (+)

and minus (-) diagrams inside on the

battery door.

3. Close the battery door. Push down until it

“clicks” into the locked position.

Powering the Spot Finder SF803

Components Spot Finder SF803

1 - SF803

2 - Target Plate

for Spot Finder

3 -Center Hole

4 -Power Button

5 -Bubble Vial

6 -Battery LED

7 -Mode LED

8 -Red Direction LEDs

9 -IR transmitters/receivers

10 - Marking notches (front and back)

11 - M6 Clamp Mount

12 - Battery door

13 - Latch for Battery Door

14 - Release Tab Target Plate

15 - SF Pole Adapter

1312

7 3

10 2

DG813/DG613 Components

1. Battery Compartment –holds the

NiMH battery pack. (D-Cell alkaline

batteries can be used as a backup.)

2. Battery Door Latches –locks/unlocks

and holds the battery compartment in

place.

3. LCD Graphic Display - shows the power,

grade, battery, out-of-level, beam position,

menu information and status of the laser.

4. Grade Axis Pivot Marker - identifies the

pivot point for the grade system

5. Line-Axis Pivot Marker and LED - used

to align a transit over the top of the laser;

lights for 15 minutes after turning on the

laser or pressing one of the buttons.

6. Handle - to carry the laser easily

and to attach a safety rope in manholes

with water.

4 3 2

7. Axis Alignment Markers - used to align

the laser when the line system is centered.

8. Mounts for scope adapter –to

attach the optional scope adapter for the

„Over the Top“ application

9. 5/8”-11 Threaded Mount –to attach the

laser to various setup accessories

10. Remote Receiver Window –receives

signals from the RC803 and SF803

11. Beam-Exit Window –provides a

clear window for the laser beam to exit

the pipe laser.

DG813/DG613 Components

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Spectra Precision Instrument de mesure

Spectra Precision

Spectra Precision Focus 30 Manuel utilisateur

Spectra Precision

Spectra Precision UL633 Manuel utilisateur

Spectra Precision

Spectra Precision Focus 8 Series Manuel utilisateur

Spectra Precision

Spectra Precision HV302-7 Guide d'installation

Spectra Precision

Spectra Precision DG613 Manuel technique

Spectra Precision

Spectra Precision Focus 10 Manuel utilisateur

Spectra Precision

Spectra Precision HV101 Manuel utilisateur

Spectra Precision

Spectra Precision Focus 6 Manuel utilisateur

Spectra Precision

Spectra Precision 5.2XL Manuel utilisateur

Spectra Precision

Spectra Precision FOCUS 2 Series Manuel utilisateur

Spectra Precision

Spectra Precision Trimble GL622 Manuel utilisateur

Spectra Precision

Spectra Precision FOCUS 35 Manuel utilisateur

Spectra Precision

Spectra Precision Focus 30 Manuel utilisateur

Spectra Precision

Spectra Precision LL100N Manuel utilisateur

Spectra Precision

Spectra Precision HV302G Manuel utilisateur

Spectra Precision

Spectra Precision HV302 Manuel utilisateur

Spectra Precision

Spectra Precision QuickMark Layout QML800 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur